What is the method to avoid crossing lines throughout the entire Subject 3 driving test?

2 Answers
SanRose
07/29/25 7:29am
For straight-line driving, the first step is to adjust the seat properly to find the optimal sitting position that suits you. Sitting too far forward or too far back is not conducive to steering wheel control. If the steering wheel is not held steadily and not returned to the center position, the car will naturally deviate. It is normal for the steering wheel to be unsteady. When you feel the car deviating from the straight line, turn the steering wheel in the opposite direction to correct it.
Was this review help?
6
2
Share
DiCharlotte
08/12/25 10:47am
When I was learning to drive, I always crossed the line during Subject 3. Later, I realized the key is visual guidance. While driving, focus your eyes on a distant central point on the road, like a road sign or a tree, and avoid letting your gaze fall on the lane divider; otherwise, the car will drift. Hold the steering wheel lightly and make only minor adjustments—don’t turn too sharply, as that easily leads to crossing the line. Maintain a steady speed, around 25-30 km/h; drive steadily on straight sections, slow down before curves, and accelerate out of them. Practice is crucial: find an empty space, draw lines to simulate the road, and drive repeatedly dozens of times to get a feel for the wheel position. The examiner doesn’t just check for line-crossing but also focuses on overall stability. Spend more time practicing, and staying within the lines will become natural. Stay relaxed on the test day, breathe calmly, and don’t let nerves disrupt your control.
Was this review help?
13
4
Share
Expand All
More Forum Discussions

What are the components of the piston connecting rod assembly?

Piston connecting rod assembly mainly consists of piston, piston ring, piston pin, connecting rod and connecting rod bearing, etc. The following is a detailed introduction of the piston connecting rod assembly: 1. The piston connecting rod assembly converts the reciprocating motion of the piston into the rotational motion of the crankshaft, and at the same time converts the force acting on the piston into the output torque of the crankshaft to drive the rotation of the car wheels. 2. The piston connecting rod assembly is the transmission part of the engine, which transmits the pressure of the combustion gas to the crankshaft, causing the crankshaft to rotate and output power. 3. Common failures of the piston connecting rod assembly: due to lack of oil, the connecting rod bearing is damaged, the piston hits the cylinder, the top cylinder is damaged, the connecting rod crankshaft is damaged, the piston ring is broken, the piston clearance is large, etc.
9
5
Share

What do D3, D2, D1 mean in automatic transmission?

D1, D2, and D3 in automatic transmission refer to the low-gear modes of the gearbox. D1 manually locks the car's gear in first gear, overriding the vehicle's automatic control. D2 locks the gear in second gear, not exceeding second gear, allowing the car to shift automatically between first and second gears. D3 locks the gear in third gear, allowing automatic shifting between first, second, and third gears, but not exceeding third gear. Scenarios where D1, D2, and D3 can be used are as follows: 1. D1 and D2 can be used when going uphill, especially on steep slopes. Manually setting the gear to first or second gear is similar to using a manual transmission on a steep incline. The low gear provides higher torque, making it easier to climb. While this isn't the primary purpose (since D mode can also handle it), locking the gear prevents frequent shifting in D mode. 2. The advantage of D3 is faster response when overtaking. At speeds of 80 km/h, the gear is usually in 5th or 6th. If you need to overtake quickly, the automatic transmission will gradually downshift from 6th to 5th, 4th, and then 3rd, which takes time. By directly shifting to D3, the gear immediately changes to 3rd, providing the fastest response for instant acceleration. After overtaking, you can shift back to D mode. 3. The biggest benefit of D1 and D2 is when driving downhill. In D mode, even without pressing the accelerator, the car will accelerate, making it difficult to control and potentially dangerous. However, when shifted to D2, the car descends slowly due to the resistance from the transmission and engine, improving safety and control. Some cars even promote a "hill descent control" feature, which achieves the same effect with a simple button press.
6
1
Share

What Are the Reasons for Difficulty Starting a Car in the Morning?

Difficulty starting a car in the morning may be caused by carbon buildup in the throttle body, dirty fuel injectors, insufficient battery charge, etc. Carbon Buildup in the Throttle Body: Carbon buildup in the throttle body can affect the sensitivity of the throttle and air intake, causing delays or errors in the computer's signal transmission, which may prevent the vehicle from starting. The throttle body should be cleaned promptly. Dirty Fuel Injectors: After driving for a period of time, some gummy deposits can easily adhere to the fuel injectors. These deposits can obstruct normal fuel injection, leading to poor gasoline atomization, delayed ignition, and difficulty starting the car. It is essential to clean the fuel injectors in time. Insufficient Battery Charge: Difficulty starting the car may also be caused by insufficient battery charge. Over time, the battery may no longer hold a full charge, making it difficult to start the vehicle, especially during winter. You can check the battery's condition and its wear level. If the wear exceeds 90%, the battery should be replaced immediately. After replacement, the vehicle will function normally without significant impact.
8
0
Share

What Displacement Motorcycles Can Be Licensed?

Currently, the maximum displacement allowed for motorcycles in China is above 250cc. Theoretically, any domestically produced motorcycle with a certificate of conformity can be licensed. According to regulations, any motor vehicle weighing over 40KG or with a maximum speed exceeding 20KM/h is classified as a motor vehicle and must be licensed before it can be driven on the road. Introduction to Displacement: Displacement, a specialized term in hydraulic transmission, refers to the volume of fluid inhaled or expelled per stroke or cycle. The space volume through which the piston moves from the top dead center to the bottom dead center is called the cylinder displacement; if the engine has multiple cylinders, the sum of the working volumes of all cylinders is called the engine displacement. It is generally expressed in liters (L). The Importance of Engine Displacement: Engine displacement is one of the most important structural parameters, more representative of the engine's size than cylinder bore and number. Many engine indicators are closely related to displacement. Generally, a larger displacement means the engine releases more energy per unit time (converting the chemical energy of fuel into mechanical energy), which translates to better "power performance." This is similar to comparing a teenage boy to a healthy adult—the adult is naturally more efficient at physical labor. Therefore, off-road vehicles and sports cars usually have relatively larger displacements.
16
1
Share

What is the speed limit on the Xuming Expressway?

The entire Wuhu section of the Xuming Expressway has a speed limit of 80 kilometers per hour. Precautions for expressway driving: Pay attention to the signs on both sides of the road. Slow down when seeing signs for accident-prone areas and crosswinds. When the exit is about one kilometer away, move to the right lane; use lanes properly; master overtaking techniques—complete overtaking quickly and minimize parallel driving time; obey traffic laws. Driving safety precautions: Always fasten your seat belt—do not treat it as a decoration or just for inspection purposes. Avoid fatigued driving; if feeling drowsy, find a place to rest. Stay focused while driving, and never drive under the influence of alcohol—drunk driving has severe consequences. In adverse weather conditions, prioritize driving safety, avoid speeding, be aware of road conditions, steer clear of hazardous areas, and ensure safe driving. Never make a U-turn on the expressway. In case of a breakdown, immediately turn on the hazard warning lights, move the vehicle to a safe spot away from traffic, and keep the hazard lights on if the vehicle cannot be moved.
12
3
Share

What is the ST light on the Aoling dashboard?

st light is the brake filament breakage warning light. Function of the ST light: Indicator light, the dashboard display consists of an S and a T. When this light comes on, promptly check if the brake light filament is broken and address it immediately; if the brake light filament is intact, it may indicate a relay malfunction, and it is recommended to contact a service station for inspection. Most vehicles have two brake lights, while some have three. For vehicles with three brake lights, the third one is located on the rear windshield and serves as a high-mounted brake light. When the brake pedal is pressed, the brake lights illuminate to alert drivers behind to maintain a safe distance, helping to prevent rear-end collisions. Function of the brake filament breakage controller: The brake filament breakage controller informs the driver whether the brake lights are functioning. In some vehicles, if one brake light fails, all brake lights will not illuminate, and an indicator on the dashboard will display. In such cases, the driver should inspect the brake system. The controller is connected behind the relay with four wires: the relay contact point, brake light wire, ground wire, and dashboard light wire.
15
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.