What is the method for removing the fuel filter clip?

1 Answers
DiLaila
07/30/25 8:18am
Disassembly method for the fuel filter clip is as follows: 1. Lift the vehicle and unplug the sensor wire connector on the fuel filter. 2. Use a tool to remove the base screws of the fuel filter, typically requiring a 10cm wrench or a Torx screwdriver. 3. Use a screwdriver to remove the clip of the fuel filter and pull it backward, the other end follows the same disassembly method. 4. When removing, note the arrow on the fuel filter; if the arrow is unclear, remember that the larger end of the fuel filter should face upwards. 5. Remove the fuel filter and install the new one according to the orientation and size of the old fuel filter, as incorrect installation direction may affect the fuel line operation.
Was this review help?
8
5
Share
More Forum Discussions

What is the difference between multi-point injection and direct injection?

Here are the differences between direct injection and multi-point injection: Control method: Direct injection is mechanical injection; multi-point injection requires injection based on signals such as air flow, water temperature, throttle opening, and engine load for knock. Characteristics: The engine has high fuel injection precision, and there is no need to worry about gasoline adhering to the intake manifold. Direct injection in the cylinder can increase the compression ratio, and atomized gasoline can directly reduce the temperature in the cylinder, achieving stratified combustion. The gas mixes with gasoline in the intake manifold, making the mixture more uniform. The angle of the injector is just right to face the valve, and during injection, gasoline can to some extent clean the carbon deposits on the valve, with good reliability and easy maintenance. The injector is not inside the cylinder, so it is not affected by high temperature and high pressure environments.
13
1
Share

What Components Make Up the Steering Control Mechanism?

Steering control mechanism is primarily composed of steering wheel, steering column, steering shaft, and steering universal joint. Below is an introduction to relevant knowledge about the steering control mechanism: Function: The function of the automotive steering control mechanism is to transmit the driver's steering wheel operation force to the steering gear. Components: It includes: steering wheel, steering column tube, steering shaft, upper universal joint, lower universal joint, and steering transmission shaft, etc. The middle part of the steering column tube is fixed to the front bulkhead of the cab with rubber pads and a semi-circular stamped bracket, while the lower end is inserted into the hole of a cast iron support. The support is then fixed to the steering control mechanism bracket.
17
1
Share

What to Do If Your Driver's License Has Expired for Over a Year?

Here are the steps to handle a driver's license that has been expired for over a year: Subject 1 Exam: If your motor vehicle driver's license has expired for more than one year without renewal, it will be revoked. However, if the revocation period does not exceed two years, you can apply at the local vehicle management office to take the Subject 1 exam. Passing the exam will restore your license. License Renewal: If your driver's license has been revoked for more than two years, you will need to retake all the exams. If your license has expired, you should renew it immediately. Documents Required: If your driver's license has expired within the past year, you can still follow the normal renewal procedures. You will need to provide a physical condition certificate issued by a county-level or military regiment-level medical institution, original and photocopies of your ID, the original driver's license, a motor vehicle driver's license application form, and three recent 1-inch color photos with a white background. You can choose to process the renewal at the nearest traffic police station, vehicle management office branch, or one-stop units authorized by the traffic management department.
9
1
Share

Will a Non-Full-Size Spare Tire Cause the Car to Pull to One Side?

Spare tires that are not full-size may cause the car to pull to one side. Below is an introduction to the related content: Definition: A non-full-size spare tire refers to a tire that is smaller in diameter and narrower in width compared to the regular tires. Force Distribution: After installation, the force distribution on both sides of the car will be uneven during driving. Spare Tire: A spare tire is a backup tire prepared for a car. In case of a flat tire or any issue with a regular tire, the spare tire allows for timely replacement, preventing the car from breaking down midway. Tire: A tire is a circular, elastic rubber product mounted on various vehicles or machinery to roll on the ground. Tires are usually installed on metal rims, supporting the vehicle body, cushioning external impacts, ensuring contact with the road surface, and maintaining the vehicle's driving performance.
3
4
Share

How to Set Up a Car Three-Band Equalizer?

Car three-band equalizer setup standards are as follows: Bass Band: Adjust the center frequency within the range of 60Hz~250Hz. At the appropriate frequency, the sound is relaxed and deep. If set too low, the sound may appear thin; if set too high, prolonged listening may cause discomfort to the eardrums. Midrange Band: The center frequency can be adjusted within the range of 1kHz~4kHz, creating a sense of presence. At the right frequency, the sound becomes clearer and brighter. Treble Band: The center frequency should be adjusted within the range of 6kHz~15kHz. The sound is relatively delicate, but setting it too high may cause distortion.
10
5
Share

What is the procedure for reporting the loss and reissuance of a vehicle license?

The 'Motor Vehicle License' is lost or missing, the owner of the motor vehicle should fill out the 'Application for Replacement or Renewal of Motor Vehicle License Plates and Certificates', and apply for the reissuance of the 'Motor Vehicle License' at the vehicle management office under the jurisdiction of the motor vehicle. Below is an introduction to the vehicle license: Introduction: The vehicle license is the legal document that permits a motor vehicle to drive on roads within China. It consists of three parts: the license holder, the main page, and the supplementary page. The front of the main page is the signed and stamped certificate core, the back is the photo of the motor vehicle, and the supplementary page is the signed and stamped certificate core. Required Materials: Documents to be carried include the vehicle license pending processing voucher, road maintenance fee payment voucher, and registration and filing materials from the safety committee. Processing Location: It should be processed at the same vehicle management office where the vehicle's license plate was obtained.
10
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.