What is the Mercedes-Benz V-Class?

How to Adjust the Valve Clearance of the Aowei 13-liter Engine?

Locate the top dead center of the first cylinder piston at the end of compression, adjust half of the valves, then rotate the crankshaft one full turn to adjust the remaining half of the valve clearances. When adjusting the valve clearances of the engine, besides paying attention to the adjustment sequence, the size of the clearance is also crucial. If the valve clearance is adjusted too small, the valve may not close tightly, leading to a decrease in engine power. If the clearance is adjusted too large, it will increase the number of impacts on the valve train components, accelerating wear. It may also cause delayed valve opening, resulting in reduced engine performance and inability to operate normally. Precautions for engine use are as follows: 1. Overheating: If the engine overheats while driving, you can release the accelerator pedal, shift the transmission to a lower gear, or perform both actions simultaneously to reduce power output until the engine temperature returns to the normal operating range. 2. High-sulfur fuel: Under certain operating conditions, such as low speed, low load, or starting a work cycle after shutdown, the operating temperature of the engine's after-treatment catalyst may not be very high. If unauthorized high-sulfur fuel is used, ammonium sulfate may accumulate on the catalyst, reducing the NOx conversion efficiency in the SCR system. As a result, the engine may fail to meet emission regulations.

12

0

Share

What is the refrigerant in the air conditioner called?

Refrigerant is also known as refrigeration working fluid. Here is an introduction to refrigerant: 1. In some southern regions, it is commonly known as "snow seed." It is a working substance that continuously circulates in the refrigeration system and achieves cooling through changes in its own state. 2. The refrigerant absorbs heat from the cooled medium (such as water or air) in the evaporator and vaporizes, then transfers the heat to the surrounding air or water in the condenser and condenses. Precautions for adding refrigerant to a car: 1. Before using the machine, the oil plug on the vacuum pump must be replaced, and the exhaust oil plug must be swapped out. 2. The vacuum gauge must not be subjected to high pressure. The vacuum gauge valve V3 must be closed before connecting the high and low-pressure pipes and adding refrigerant. 3. The force used to close the valves should be moderate. Tightening force should be minimized as much as possible without causing leaks to extend the service life of the valves. However, even if the sealing parts are damaged after long-term use, repair and replacement are very simple. 4. Pure refrigerant without solid impurities should be used. 5. All valves must be closed after the operation is completed.

19

3

Share

Which brand is the transmission of the Volvo S90?

The Volvo S90 uses an 8AT transmission. Here are the relevant details about the AT transmission: 1. The AT transmission technology is mature and widely used. 2. The AT transmission is connected to the engine via a torque converter, providing relatively smooth shifting. 3. The AT transmission consists entirely of planetary gears, relying on them for speed and torque variation. 4. The 8AT transmission offers high transmission efficiency and smooth shifting. 5. It can quickly respond to changes in engine speed, shift smoothly, and effectively utilize the engine's torque and power range with multiple selectable gear ratios.

6

4

Share

What does the classic Focus fault code p2008 mean?

The classic Focus fault code p2008 may indicate a vacuum solenoid valve malfunction. The vacuum solenoid valve is a specialized valve installed on a mechanical vacuum pump. The valve and the pump are connected to the same power source, so the pump's activation and deactivation directly control the valve's opening and closing. When the pump stops working or the power is suddenly interrupted, the valve automatically seals the vacuum system and allows atmospheric air to enter the pump chamber through the pump's intake port, preventing pump oil backflow from contaminating the vacuum system. Here are some related details: 1. The vacuum solenoid valve is suitable for working with air and non-corrosive gases. Its primary function is to activate the vacuum pipeline when the solenoid valve circuit is energized after the engine starts, enabling the vacuum control valve to operate. Different vacuum control valves can perform functions such as opening/closing flaps, increasing idle speed, and operating door locks, and are commonly used in automotive air conditioning systems. 2. In the air conditioning system, the vacuum solenoid valve plays a role in energizing the electromagnetic clutch circuit while also activating the vacuum switching valve's electromagnetic coil. The vacuum switching valve increases the throttle opening of the carburetor via a control rod, thereby raising the idle speed.

10

2

Share

How to reset the tire pressure warning light on a 2017 Outlander?

The method to reset the tire pressure warning light on a 2017 Outlander: First, turn on the ignition switch, then press and hold the tire pressure monitoring reset button until you hear a "dong" sound before releasing it. The tire pressure monitoring system will then store the current normal tire pressure data, automatically clear the previous data, and finally, the warning light on the dashboard will turn off, completing the tire pressure reset. Precautions for inflating tires: Always use a pressure gauge to check the tire pressure to avoid over-inflation, which could cause the tire to burst. After stopping the vehicle, wait for the tires to cool down before inflating, as the tire temperature rises during driving, affecting the pressure. Check the valve stem. If the valve stem and valve core are not properly aligned, have protrusions or depressions, or other defects, it may be difficult to inflate or measure the pressure. Pay attention to cleanliness when inflating. The air being pumped in should not contain moisture or oil, as this could deteriorate and damage the inner tube rubber. Do not exceed the standard pressure too much when inflating and then release air, nor should you over-inflate the tires because you haven't been able to inflate them for a long time while traveling. Exceeding the standard pressure too much can cause the cords to overstretch, reducing their strength and affecting the tire's lifespan.

17

2

Share

How to Reset the Maintenance Indicator on Volkswagen Lamando?

Volkswagen Lamando Maintenance Light Reset Procedure: 1. Turn off the ignition switch and stop the engine. 2. Press and hold the "0.0" button (reset button) on the instrument panel. 3. Turn on the ignition switch while keeping the "0.0" button pressed. 4. Release the "0.0" button when one of the following messages appears on the instrument cluster display. 5. Press the "0.0" button again to confirm (single press is sufficient). 6. Check if the maintenance light has been reset. If not, restart the procedure from the beginning. 7. For infotainment system maintenance messages: Press CAR → Settings → Maintenance → Reset Maintenance Information → Confirm.

14

4

Share

What is the Mercedes-Benz V-Class?

How to Adjust the Valve Clearance of the Aowei 13-liter Engine?

What is the refrigerant in the air conditioner called?

Which brand is the transmission of the Volvo S90?

What does the classic Focus fault code p2008 mean?

How to reset the tire pressure warning light on a 2017 Outlander?

How to Reset the Maintenance Indicator on Volkswagen Lamando?

What does 'sports' mean on a car in Chinese?

What does collision warning with automatic braking mean?

How Long Does It Take to Fully Charge a Tesla?

What type of driver's license is required to drive a medium-sized bus?