···
Log in / Register

What is the maximum wading depth of the Wuling Zhiguang?

1 Answers
McMicah
07/23/25 12:35pm

The maximum wading depth of the Wuling Zhiguang is 260mm. The wading depth of the Wuling Zhiguang is determined by the height of the vehicle's chassis, which is the ground clearance listed in the model's parameter configuration table. Generally, the greater the ground clearance, the higher the chassis, and the higher the safety factor when driving through waterlogged roads. Therefore, in terms of safe wading depth, off-road vehicles and SUVs have obvious advantages. However, for most compact cars and small cars with low chassis, the position of the vehicle's air intake should be used as a reference when passing through waterlogged roads. If the air intake of the Wuling Zhiguang is below the water level during wading, water will be sucked into the engine's cylinders. Since water cannot be compressed like air, it will cause severe damage to the engine's mechanical components (such as connecting rods, pistons, crankshafts, etc.). Therefore, the wading depth should not exceed the height of the engine's air intake. The height of the engine's air intake (and thus the maximum wading depth) can also be increased by installing a snorkel. If wading is unavoidable, the following safe and correct operations should be performed: Before wading, always turn off the auto start-stop function to prevent the engine from automatically restarting after stalling in water, which could cause severe damage due to water ingestion. Assess the underwater road conditions based on the passage of preceding vehicles and choose an appropriate entry point. Observe the path taken by other vehicles and follow their tracks at low speed, avoiding sudden acceleration or deceleration. On roads prone to water accumulation, observe warning water level markers, trees, or other vehicles' wheels and doors as reference points to judge the water depth before deciding whether to proceed. Know your vehicle's safe wading depth. If the water depth exceeds half of the tire height or the engine's air intake, do not proceed and choose an alternative route instead.

Was this review help?
3
4
Share
More Forum Discussions

What are the techniques for depressing the clutch?

The methods for depressing the clutch are as follows: 1. Depress the clutch quickly to ensure complete separation and avoid clutch slippage; 2. Release the clutch slowly to ensure smooth vehicle operation; 3. Do not depress the clutch arbitrarily. Precautions for clutch usage are: 1. The clutch must be thoroughly cleaned before installation to remove anti-rust grease and debris; 2. The clutch can be installed coaxially or separately, but the axial direction must be fixed; 3. For wet electromagnetic clutches, lubricating oil must be added between the friction plates during operation; 4. The power supply and control circuits should be noted, with the clutch power supply being 24V DC; 5. When installing a jaw-type electromagnetic clutch, ensure there is a certain gap between the end face teeth to prevent grinding during idle operation.
7
2
Share

What is the normal tire pressure in kPa?

Generally, a tire pressure value between 2.3 and 2.5 is considered normal. If the car is fully loaded (5 people), it is more appropriate to adjust the tire pressure to around 2.5. In general, there are two situations where a tire pressure value of 2.3 is also normal. Content Extension: 1. The standard tire pressure value is inherently a conservative figure, allowing for minor fluctuations. Therefore, whether in winter or summer, tires should be inflated according to the standard tire pressure. As long as the standard tire pressure is maintained, there is no need to worry about the impact of external temperature on tire pressure, and there is no necessity to adjust the inflation pressure standard based on temperature variations. 2. Tires require the correct pressure value to function effectively; neither too low nor too high tire pressure is good. 3. Low tire pressure can lead to: tire overload and overheating, which may even cause tire explosions, premature or irregular wear, poor handling, and reduced fuel economy. 4. High tire pressure can result in: abnormal wear, poor handling, reduced ride comfort, and unnecessary damage due to road hazards.
8
3
Share

What is the vehicle and vessel tax for a 2.4L displacement car?

For passenger vehicles with a 2.4L displacement and seating capacity of 9 or fewer, the annual vehicle and vessel tax ranges from 720 to 900. The vehicle and vessel tax not only varies based on the car's displacement but also differs across regions, meaning the same displacement vehicles may have different tax standards in different areas. Extended Content: 1. For motor vehicles (excluding trucks) and non-motor vehicles, the tax payable = number of taxable vehicles × unit tax amount. 2. For trucks, motorized boats, and non-motorized boats, the tax payable = tonnage or net tonnage of the vehicle or boat × unit tax amount.
19
3
Share

What Causes an Automatic Transmission Car to Not Move When Shifted to D Gear?

Here are the specific reasons why an automatic transmission car does not move after shifting to D gear: 1. Check if the transmission fluid level is too low, whether the main oil pressure and gear oil pressure are normal, and then verify if the gear switch signal is normal, if the wiring from the transmission computer to the shift solenoid valve is intact, and if the gear solenoid valve is functioning properly. 2. If none of the above issues are found, it indicates a problem with the internal control system of the transmission, requiring disassembly of the transmission to inspect the internal components. Below is additional information about automatic transmission gears: (1) The R gear is the reverse gear. When engaged, it connects the hydraulic system to the reverse gear circuit, causing the drive wheels to turn in reverse for backing up. Do not forcibly shift to "R" gear when the vehicle is not completely stopped, as this can damage the transmission. (2) The N gear is the neutral gear. When in neutral, the planetary gear system idles without transmitting power. (3) The D gear is the drive gear. When the shift lever is in this position, the hydraulic control system automatically engages the appropriate forward gear circuit based on throttle opening and vehicle speed signals, shifting gears automatically as speed changes to achieve automatic transmission functionality. (4) The P gear is the parking gear. It uses a mechanical device to lock the rotating parts of the car's tires, preventing the vehicle from moving.
12
2
Share

What to do if three windows of BYD S6 malfunction?

If three windows of BYD S6 malfunction, lift the window button directly to raise the window to the top, hold for 3-5 seconds and then release. Then press the window button to lower the window to the bottom, hold for 3-5 seconds and release. Here is more information about BYD: 1. BYD is a Chinese automobile brand founded in 1995, mainly producing commercial cars, family cars, and batteries. 2. Representative models of BYD include traditional high-quality fuel vehicles such as F3, F3R, F6, F0, G3, G3R, L3/G6, and Surui, the S8 sports hardtop convertible, the high-end SUV model S6 and MPV model M6, as well as the globally leading F3DM, F6DM dual-mode electric vehicles and the pure electric vehicle E6.
6
4
Share

What does it mean to schedule two sessions for Subject One?

Subject One scheduling two sessions is mainly to increase the chance of successful registration. Here is the relevant introduction about Subject One: 1. Exam Introduction: The driver's license exam Subject One tests theoretical knowledge, conducted at the DMV, and is a mandatory licensing exam for applicants. The exam content includes the most basic knowledge such as driving theory foundation, road safety laws and regulations, traffic signals, traffic rules, plus local regulations. The schedule for the driver theory exam is arranged by local DMVs. 2. Exam Process: The total time for the Subject One exam is 45 minutes, with the exam paper consisting of 100 questions, including true/false and single-choice questions, with a full score of 100 and a passing score of 90. The exam paper is randomly selected and combined by the computer driver exam system according to the proportion specified in the "Motor Vehicle Driver's License Business Work Standards."
7
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.