What is the maximum wading depth of the Mercedes-Benz G63?

1 Answers
DelZoey
07/24/25 5:25pm
The maximum wading depth of the Mercedes-Benz G63 is 600mm. The wading depth of the Mercedes-Benz G63 is determined by the height of the vehicle's chassis, which is the ground clearance listed in the model's parameter configuration table. Generally, the greater the ground clearance, the higher the chassis, and the higher the safety factor when passing through waterlogged roads. Therefore, in terms of safe wading depth, the advantages of off-road vehicles and SUVs are obvious. However, for most compact and small cars with low chassis, the position of the vehicle's air intake should be used as a benchmark when passing through waterlogged roads. If the air intake of the Mercedes-Benz G63 is below the water level during wading, water will be sucked into the engine's cylinders. Since water cannot be compressed like air, it will cause severe damage to the engine's mechanical components (such as connecting rods, pistons, crankshafts, etc.). Therefore, the wading depth should not exceed the height of the engine's air intake. The height of the engine's air intake, and thus the maximum wading depth, can also be increased by installing a snorkel. If wading is unavoidable, the following safe and correct operations should be performed: Before wading, always turn off the auto start-stop function to prevent the vehicle from automatically restarting after stalling in water, which could cause severe engine damage due to water ingress. Assess the underwater road conditions based on the passage of preceding vehicles and choose an appropriate entry point. Observe the path taken by other vehicles and follow it at a low speed, avoiding sudden acceleration or deceleration. On roads prone to water accumulation, use warning water level markers, trees, or the wheels and doors of other vehicles as reference points to judge the water depth before deciding whether to proceed. Know your vehicle's safe wading depth. If the water depth exceeds half the tire height or the engine's air intake, do not proceed and choose an alternative route instead.
Was this review help?
15
1
Share
More Forum Discussions

What are the gear modes of the Nissan Patrol?

The Nissan Patrol has two gear modes: A and B. The switch is located at the lower right corner of the gear shift and requires manual adjustment. The Nissan Patrol is Nissan's first full-size SUV, with dimensions of 5165mm in length, 1995mm in width, and 1955mm in height, a wheelbase of 3075mm, a maximum power of 205kw, and a maximum torque of 394nm. In terms of power: The Nissan Patrol is equipped with a 5.6L V8 engine, featuring gasoline direct injection system technology. It comes standard with cruise control, front and rear parking radar, hill start assist, and hill descent control. The rear door is designed as a split type, and the exterior features a straight-line design.
19
4
Share

What are the differences between 92via and 92vi?

92via gasoline refers to ethanol gasoline, which is a new alternative energy source formed by blending fuel ethanol processed from grains and various plant fibers with regular gasoline in a certain proportion. The 'vi' in 92vi stands for 'Ⅵ', indicating that it is gasoline compliant with the China VI emission standard. It is mandatory to sell China VI standard fuel before selling China VI standard vehicles, and it is absolutely unacceptable to use China V standard fuel in China VI vehicles. Gasoline Anti-Knock Performance: The ability of automotive gasoline to resist knocking and ensure normal combustion. After the mixture of automotive gasoline and air is ignited by the spark plug in the combustion chamber of the gasoline engine, the flame should spread evenly and stably throughout the entire combustion chamber. Gasoline Stability: The ability of gasoline to resist oxidation under certain external conditions, referred to as stability. During storage, gasoline oxidizes to form gums and corrosive oxides. The deposition of gums in the vehicle's fuel supply system can reduce fuel delivery and decrease engine power.
3
0
Share

How many points will be deducted for driving at 160 km/h on the highway?

Points deduction is determined based on the road section where the driver was driving. If on the highway, where the unmarked speed limit is generally 120 km/h, then the driver is speeding by 30%. Some highways may have a higher limit than 120 km/h. If the speed limit is 80 km/h, then the driver is speeding by 100%. 12 points will be deducted for speeding: Driving passenger or cargo vehicles, school buses, or hazardous material transport vehicles on highways or urban expressways at speeds exceeding 20% above the posted limit, or on other roads at speeds exceeding 50% above the posted limit, or driving any motor vehicle at speeds exceeding 50% above the posted limit. Recommended handling method: Pay the fine promptly and attend a seven-day traffic safety law and regulation study session and exam at the traffic management department of the public security authority where the driver's license was issued or where the violation occurred. The driver's license will be returned upon passing the exam.
10
2
Share

How long does it usually take for a 4S shop to repair a car?

For major repairs, it may take half a month to a month. If it's just minor repairs, such as purchasing external parts, painting, or sheet metal work, it usually takes about a week. Factors affecting repair speed: Parts procurement: The first factor is whether the required parts need to be procured. If procurement is needed, it depends on the manufacturer's delivery speed. 4S shops usually order parts from the manufacturer once a week. If the 4S shop happens to have the required parts in stock, the repair can usually be completed on the same day. Number of vehicles: The number of cars being repaired at the 4S shop also affects the repair time. Repairs are done on a first-come, first-served basis. If there are many cars being repaired at the 4S shop, naturally, it will take more time. Insurance claims: For repairs involving insurance claims, the speed of repair depends on the extent of the vehicle's damage, the determination of insurance liability, and the time it takes for the insurance company to confirm the claim.
9
1
Share

How to Deal with Driving an Uninspected Vehicle?

If a vehicle's annual inspection is overdue, traffic police will impose a fine and deduct 3 points upon inspection and seizure. Vehicles that fail to obtain the mandatory inspection compliance mark within three consecutive inspection cycles after the expiration of the inspection validity period will be deregistered. Therefore, deregistration occurs once three cycles are exceeded. Timely Handling of Violations: It is important to clear any traffic violations of the vehicle in advance and ensure the vehicle is properly prepared; otherwise, it will not pass the annual inspection. Only vehicles with no violations and in good condition can pass the annual inspection. Prohibition of Illegal Modifications: The vehicle's appearance must match that on the vehicle registration certificate, and illegal modifications are not allowed. If the car has been modified with body kits, spoilers, or rims without filing the changes with the vehicle management office, it must be restored to its original factory condition before undergoing the annual inspection.
20
3
Share

What are the reasons for the car air conditioning compressor not working?

Reasons for the car air conditioning compressor not working: 1. Circuit system failure, short circuit or open circuit in the circuit directly loses the path for power transmission, and the electromagnetic clutch cannot normally control the working state of the compressor; 2. Lack of refrigerant, refrigerant and refrigeration oil are mutually soluble, circulating back to the compressor through the system. If the Freon in the refrigerant is exhausted, it will lead to insufficient oil return of the refrigeration oil, reducing the lubrication effect of the compressor and causing it to jam and damage; 3. Mechanical wear of the compressor, long-term operation under high-speed load conditions may cause premature mechanical wear of compressor parts, making it unable to work; 4. The belt is too tight, excessive tightness of the belt will directly cause the compressor to jam and not operate, so it is necessary to frequently check the tightness of the belt. At the same time, excessive looseness will cause the compressor's transmission power to slip, resulting in intermittent refrigeration effects and reduced power.
10
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.