What is the maximum wading depth of the Maxus D90?

1 Answers
Smith
07/30/25 8:10am
The maximum wading depth of the Maxus D90 is 800mm. The SAIC Maxus D90 Pro has quite good off-road capability, with an approach angle of 28 degrees, minimum ground clearance of 210mm, maximum wading depth of 800mm, departure angle of 25 degrees, and waterproof one-way valves at the low points of the chassis. The air intake is located above the right wheel arch, and the manufacturer's stated maximum wading depth is 800mm. If higher-intensity wading conditions need to be handled, a snorkel can be optionally installed. The Maxus D90 Pro has a body length, width, and height of 5005/1932/1875mm, a wheelbase of 2950mm, and can be factory-fitted with all-terrain tires. The photographed vehicle is equipped with Pirelli Scorpion all-terrain tires in size 255/60R18.
Was this review help?
12
1
Share
More Forum Discussions

What to Do When the Car Battery Dies After Long-Term Parking?

Here are the solutions when the car battery dies after long-term parking: 1. If the car battery dies after long-term parking, you can ask relatives or friends to come with jumper cables. Park the two cars either head-to-head or side by side. After parking, open both hoods, ensuring the other car remains running. Connect the positive terminals to positive and negative to negative using the jumper cables. Then, try starting the car. If there are no other issues with the vehicle, it should start successfully. 2. If no other vehicle is available for a jump-start or if you don't have jumper cables, you can call the 4S dealership or a repair shop for roadside assistance. Most 4S shops have dedicated rescue vehicles equipped with jumper cables. 3. Another option is to keep an emergency jump starter in your car. This allows you to start the car in emergencies when the battery is dead, saving a lot of hassle.
7
3
Share

Is the Lynk & Co 03 equipped with a Volvo engine?

Lynk & Co 03 is powered by a Volvo engine, as it is built on the CMA architecture jointly developed by Geely and Volvo. More details about the Lynk & Co 03 engine are as follows: 1. At the time of its launch, the Lynk & Co 03 came with three engine options: the first was a low-power version of the 1.5L turbocharged engine, the second was a high-power version of the 1.5L turbocharged engine, and the last was a 2.0L turbocharged engine. 2. The maximum power outputs of these three engines are 115kW, 132kW, and 140kW, respectively, showing significant differences. However, these engines share the common feature of being equipped with direct fuel injection technology and utilizing aluminum alloy cylinder heads and blocks. As for the transmission, the 1.5L turbocharged engines are paired with a 7-speed dual-clutch transmission, while the 2.0L engine is matched with a 6-speed automatic transmission.
20
3
Share

What Causes Abnormal Noise After Accelerating the Engine?

Engine abnormal noise after accelerating may result from: engine knocking, insufficient engine oil, excessively low oil pressure, friction between valves and guides or hydraulic lifters, premature gasoline combustion when pistons fail to reach top dead center during compression stroke before spark plug ignition. Solutions: 1. Use gasoline with appropriate octane rating and avoid refueling at unknown gas stations; 2. When forced to use substandard fuel in extreme conditions, employ a gasoline funnel to filter out most water and impurities, thereby improving fuel quality. An engine (Engine) is a machine that converts various forms of energy into mechanical energy, including internal combustion engines (reciprocating piston engines), external combustion engines (Stirling engines, steam engines, etc.), jet engines, electric motors, etc.
1
1
Share

What are the reasons for the Golf 7 center console screen not lighting up?

Golf 7 center console screen not lighting up reasons are as follows: 1. Poor line contact: It is necessary to promptly check whether the line has a loose connection. If there is, it will naturally cause the center console screen not to light up, just connect the loose part properly. 2. Aging power signal line: You can try to replace it with a new one. If the black screen is resolved, it means that the power signal line is indeed problematic. 3. Module abnormality or design defect: The screen has been used for too long, causing the power supply module to malfunction, not only causing lag but also severe black screen phenomenon. It may also be due to circuit design defects. However, problems like module abnormalities and design defects require inspection and repair at a repair shop or direct replacement.
14
3
Share

Is the Mercedes-Benz E300 wheel hub forged or cast?

Mercedes-Benz E300 wheel hubs are cast. Introduction to automobile wheel hubs: An automobile wheel hub is the rotating part of the tire inner rim connected to the wheel core through pillars, and it is also the metal component mounted on the axle that supports the tire. It is also called a wheel rim, steel rim, or tire ring. Surface treatment processes for automobile wheel hubs: Depending on the characteristics and requirements of different vehicle models, the surface treatment processes for wheel hubs will also vary. They can be divided into painting and electroplating. Maintenance methods for automobile wheel hubs: Avoid using cold water to clean when the wheel hub temperature is high; when the vehicle is in a humid area, the wheel hub should be cleaned frequently to prevent salt from corroding the aluminum surface.
1
3
Share

How often should the timing belt on a Citroen C-Quatre be replaced?

Citroen C-Quatre's timing belt generally needs to be replaced every 90,000 kilometers or 6 years. The relevant details are as follows: 1. The timing belt is a rubber component that can deteriorate over time, affecting its performance and potentially leading to engine failure. The C-Quatre maintenance manual specifies that the timing belt should be replaced every 90,000 kilometers or every six years. 2. The steps for replacing the timing belt are as follows: (1) Remove the outer cover of the timing belt and check the alignment marks on the camshaft. There are alignment holes on both wheels on the cylinder head. (2) Remove the spark plugs and use a welding rod or other rod-like object to rotate the crankshaft until the piston reaches the top dead center position. (3) Secure the camshaft with two 10mm screw rods and mark the two timing wheels to prevent misalignment. (4) Remove the old belt and install the new one.
13
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.