What is the maximum wading depth of the Magotan?

1 Answers
SanAngelo
09/03/25 6:56am
The maximum wading depth of the Magotan is 310mm. The wading depth of the Magotan is determined by the height of the vehicle chassis, which is the ground clearance listed in the model's parameter configuration table. Generally, the greater the ground clearance, the higher the chassis, and the higher the safety factor when passing through waterlogged roads. Therefore, in terms of safe wading depth, the advantages of off-road vehicles and SUVs are obvious. However, for most compact and small cars with low chassis, the position of the vehicle's air intake should be used as a benchmark when passing through waterlogged roads. If the air intake is below the water level when the Magotan is wading, water will be sucked into the engine's cylinders. Since water cannot be compressed like air, it will cause severe damage to the engine's mechanical components (such as connecting rods, pistons, crankshafts, etc.). Therefore, the wading depth should not exceed the height of the engine's air intake. The height of the air intake, and thus the maximum wading depth, can also be increased by installing a snorkel. If wading is unavoidable, the following safe and correct operations should be performed: Before the vehicle enters the water, the auto start-stop function must be turned off to prevent the engine from automatically restarting after stalling in the water, which could cause severe damage due to water ingestion. Based on the passage of vehicles ahead, assess the underwater road conditions and choose an appropriate entry point. Observe the path taken by other vehicles and follow their tracks at low speed, avoiding sudden acceleration or deceleration. For roads prone to water accumulation, observe warning water level markers, trees, or reference points like the wheels and doors of other vehicles to estimate the water depth before deciding whether to proceed. Know your vehicle's safe wading depth. If the water depth exceeds half the tire height or the engine's air intake, do not enter the water recklessly; consider alternative routes instead.
Was this review help?
5
1
Share
More Forum Discussions

What is the difference between Land Cruiser and Land Cruiser Prado?

The Land Cruiser is actually the same vehicle as the Land Cruiser Prado, just with different names. Previously, the Land Cruiser Prado was called the Land Cruiser, but later Toyota renamed it to Land Cruiser Prado. The Land Cruiser Prado is a mid-to-large-sized SUV under Toyota, equipped with two engine options: a 4.0-liter V6 naturally aspirated engine and a 4.6-liter V8 naturally aspirated engine. The 4.0-liter V6 naturally aspirated engine delivers a maximum power of 202 kW and a maximum torque of 385 Nm, with the peak power achieved at 5,600 rpm and peak torque at 4,400 rpm. This engine features multi-point fuel injection technology and an aluminum alloy cylinder head and block, paired with a 5-speed automatic transmission. The 4.6-liter V8 naturally aspirated engine produces a maximum power of 228 kW and a maximum torque of 453 Nm, with peak power at 5,500 rpm and peak torque at 3,400 rpm. This engine also utilizes multi-point fuel injection and an aluminum alloy cylinder head and block, mated to a 6-speed automatic transmission.
7
2
Share

What vehicles can be driven with an N1 driver's license?

An N1 driver's license allows you to drive trolleybuses. The requirements for applying for a trolleybus driver's license are as follows: The trolleybus driving license can be obtained for the first time by applicants aged between 20 and 50 years old. The application must be submitted at the local vehicle management office in the applicant's registered residence, and the license can be obtained after passing a physical examination. However, general driving schools usually do not offer training programs for trolleybus licenses; specialized training driving schools are required for registration. A driver's license, also known as a driving permit, is a document issued by the government transportation department to individuals who are qualified to drive, usually in the form of a card. To obtain a driver's license, one must meet the minimum age requirement and pass a driving test. The driver's license typically specifies the types of motor vehicles the holder is allowed to drive, such as motorcycles, passenger cars, trucks, buses, etc.
9
2
Share

How often should the timing belt be replaced on a 2012 Focus?

For the 2012 Focus, the timing belt should be replaced every 40,000 to 60,000 kilometers. The timing belt is a crucial component of the engine's valve timing system, ensuring accurate intake and exhaust timing by connecting to the crankshaft with a specific transmission ratio. Unlike gears, belts are used for transmission because they produce less noise, have minimal variation, and are easier to compensate for. However, it's evident that belts have a shorter lifespan compared to metal gears, necessitating regular replacement. The Focus is a sporty A-segment car under the Ford brand, available in both hatchback and sedan versions. It is equipped with two engine options: a 1.5-liter naturally aspirated three-cylinder engine and a 1.5-liter turbocharged three-cylinder engine.
9
0
Share

What are the symptoms of a bad differential bearing?

Differential bearing failure symptoms: 1. The car will produce a buzzing sound while driving, and this abnormal noise rhythm is generally quite steady; 2. When lifting the car and shaking the hub, there will be slight play. The purpose of a car differential is to adjust the speed difference between the left and right wheels, allowing them to rotate at different speeds. There are two main causes of differential bearing failure: bearing wear or burning. Among them, improper bearing clearance not only causes axial deflection but also accelerates bearing wear, and may even directly affect the operation of other components.
5
4
Share

What Happens When a Car Radiator Rusts?

Rust in a car radiator can restrict the flow of coolant in the cooling system, reducing its heat dissipation efficiency, which may lead to engine overheating and even engine damage. The oxidation of coolant can also produce acidic substances that corrode the metal components inside the radiator, causing leaks or breakage. Methods to deal with a rusted radiator: 1. Manual cleaning: The car radiator needs to be removed and cleaned manually using hammers, scrapers, or other tools to remove scale. 2. If the radiator has scale buildup, a radiator cleaner can be used to remove it. Ordinary cleaners may not completely eliminate scale and acidic deposits inside the water channels. While they might loosen large chunks of scale, this can block the water channels, sometimes necessitating the removal of the radiator for thorough cleaning.
18
5
Share

What is the ignition advance angle of the engine?

The ignition advance angle of the engine ranges from 1.6 degrees to 12 degrees. During engine operation, the ignition timing significantly impacts the engine's performance. Ignition advance means that the spark plug fires before the piston reaches the top dead center of compression, igniting the combustible mixture in the combustion chamber. The angle through which the crankshaft rotates from the moment of ignition until the piston reaches the top dead center of compression is called the ignition advance angle. The combustion of the mixture in the cylinder occurs at a certain speed, meaning it takes a certain amount of time from the spark plug firing to the complete combustion of the combustible mixture in the cylinder. However, due to the high speed of the engine, the crankshaft can rotate through a large angle in such a short time.
20
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.