What is the maximum wading depth of the Ford Edge?

1 Answers
DelRuby
07/29/25 5:06pm
The maximum wading depth of the Ford Edge is 550mm. The wading depth of the Ford Edge is determined by the height of the vehicle's chassis, which is the ground clearance listed in the vehicle's parameter configuration table. Generally, the greater the ground clearance, the higher the chassis, and the higher the safety factor when driving through waterlogged roads. Therefore, in terms of safe wading depth, the advantages of off-road vehicles and SUVs are obvious. However, for most compact and small cars with low chassis, the position of the vehicle's air intake should be used as a reference when driving through waterlogged roads. If the air intake of the Ford Edge is below the water level during wading, water will be sucked into the engine's cylinders. Since water cannot be compressed like air, it will cause severe damage to the engine's mechanical components (such as connecting rods, pistons, crankshafts, etc.). Therefore, the wading depth should not exceed the height of the engine's air intake. Alternatively, the height of the engine's air intake (and thus the maximum wading depth) can be increased by installing a snorkel. If wading is unavoidable, the following safe and correct operations should be performed: Before driving through water, always turn off the auto start-stop function to prevent the vehicle from automatically restarting after stalling in the water, which could cause severe engine damage due to water ingress. Assess the underwater road conditions based on the passage of vehicles ahead and choose an appropriate entry point. Observe the path taken by other vehicles and follow their tracks at low speed, avoiding sudden acceleration or deceleration. On roads prone to water accumulation, use reference points such as warning water level markers, trees, or the wheels and doors of other vehicles to estimate the water depth before deciding whether to proceed. Be aware of your vehicle's safe wading depth. If the water depth exceeds half the height of the tires or the engine's air intake, do not proceed. Instead, choose an alternative route.
Was this review help?
4
3
Share
More Forum Discussions

How long does it take to occupy the emergency lane to be considered a violation?

Occupying the emergency lane is considered a violation under the following circumstances: According to the new traffic regulations, when a motor vehicle encounters traffic congestion on urban expressways or highways, stopping on the emergency lane or shoulder under non-emergency conditions will result in a fine and 6 demerit points, which must be paid within 15 days. Emergency situations allow for occupation: When the vehicle experiences sudden malfunctions that prevent normal operation, including flat tires, engine abnormalities, transmission failure, etc. If passengers in the vehicle suddenly fall ill but their lives are not in danger, the emergency lane still cannot be occupied. In cases such as childbirth or students rushing to exams, after occupying the emergency lane, proof such as birth certificates or exam admission tickets can be presented to the traffic police for explanation. Privileged vehicles (ambulances, rescue vehicles, construction vehicles, etc.) are allowed to use the emergency lane.
19
2
Share

What's the difference between 5w and 0w?

The differences between 0W and 5W engine oil are as follows: 1. Different low-temperature viscosity: Low-temperature viscosity refers to low-temperature fluidity. W is the abbreviation for winter in English. The number before W represents the low-temperature fluidity of the oil. The smaller the number, the lower the low-temperature viscosity of the oil, the better the fluidity, and the more resistant it is to low temperatures. 2. Different low-temperature resistance: Generally, 0W oil can be used at temperatures as low as -35°C, while 5W oil can only withstand temperatures as low as -30°C. As the temperature decreases, the oil becomes thicker, increasing the resistance when starting the engine. If oil with poor low-temperature fluidity is used in extremely cold conditions, it may cause the car engine to start weakly or even fail to start.
14
2
Share

How to Determine the Production Date of Tires?

Car tire production dates are generally represented by a four-digit number, where the first two digits indicate the production week and the last two digits represent the production year. For example, 2317 means the tire was produced in the 23rd week of 2017. The production date of car tires is part of a series of alphanumeric characters that start with DOT, which stands for U.S. Department of Transportation certification. The following numbers and letters represent the tire's origin information and factory code, while the last four digits indicate the production date. Below are some details about tire dates: 1. The shelf life of tires is about 4 to 5 years. Even if the tires have low mileage, they should be replaced once they exceed this period. 2. When purchasing tires, pay attention to their production date and try to avoid buying tires that have been stored for more than 3 years. Since tires are rubber products, they will degrade over time, leading to reduced performance. If cracks appear, there is a higher risk of tire blowouts, which can compromise driving safety.
19
4
Share

What brand is gititaxi tire?

gititaxi tire is a Giti brand. Giti is a mid-range tire brand with good cost performance, so it has a considerable market share. Giti Tire, founded in Singapore, entered China in 1993 and has sales subsidiaries or offices in the United States, Canada, Germany, the United Kingdom, France, Indonesia, and Brazil. More details are as follows: 1. As one of the world's leading tire manufacturers, Giti offers a comprehensive range of high-quality tires to meet the needs of various vehicles, including sedans, SUVs, off-road vehicles, racing cars, light trucks, light buses, trucks, buses, construction machinery, and agricultural machinery. Its products are sold in more than 100 countries and have been widely recognized by domestic and foreign automobile manufacturers. 2. Giti, an international tire manufacturing company, is headquartered in Shanghai and operates seven factories in five strategic cities in China. Giti Tire adopts a multi-brand strategy to meet market demands with a complete and high-quality product series, with North America and Europe as its main export markets. Its products are sold in more than 100 countries and regions worldwide. Giti is one of China's largest international tire manufacturing enterprises, ranking 14th globally in sales.
3
3
Share

What is the difference between models with 't' and without 't'?

The differences between cars with 't' and without 't' are as follows: 1. Different engines: Cars with 't' are equipped with turbocharged or supercharged engines; cars without 't' are equipped with naturally aspirated engines. 2. Different power: With the same displacement, cars with 't' have stronger power than cars without 't', approximately 40% stronger. 3. Different maintenance costs: The repair and maintenance costs for cars with 't' are much higher than those for cars without 't'. 4. Different fuel consumption: For long-distance driving, cars with 't' are more fuel-efficient because the turbocharger intervenes, allowing fuel to burn more completely; for urban driving, cars without 't' are more fuel-efficient because it's difficult for vehicles to reach speeds where the turbocharger can intervene in city driving.
5
2
Share

How to Close Car Windows After the Engine is Turned Off?

Methods to close car windows after the engine is turned off: For vehicles equipped with automatic window lift functionality, the windows will automatically close approximately 5 seconds after the engine is turned off. If the vehicle does not have automatic window lift functionality, the windows cannot be closed after the engine is turned off, and you will need to restart the engine to close them. Windows are an essential part of the vehicle body, designed to meet the needs of interior lighting, ventilation, and visibility for the driver and passengers. Depending on the installation position of the glass, windows can be categorized into front and rear windshields, side windows, and door windows. The design, structure, and quality of the windows significantly impact the driver's visibility, passenger comfort, aesthetic appearance, and aerodynamic characteristics. Typically, car windows are designed as curved, sealed structures, with rubber sealing strips connecting the window frame to the glass. These sealing strips provide both sealing and cushioning effects, preventing damage to the windshield in case of deformation of the window frame due to stress on the vehicle body.
8
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.