What is the maximum wading depth of Dongfeng Mengshi?

3 Answers
LeAlexander
07/29/25 11:35am
According to official information, the maximum wading depth of Mengshi is 750mm. Common tire specifications are 37/12.5R16.5, the vehicle height is 1912mm, the total mass is 3480kg, and it is a 5-door 4-seat SUV. The maximum wading depth refers to the deepest water a vehicle can pass through safely. Generally, the maximum wading depth of sedans does not exceed 300mm, while SUVs can handle deeper water, but it is best not to exceed 500mm. Among common models, the GAC Trumpchi GS8 has a maximum wading depth of 700mm, the Audi A4 has 320mm, the Volkswagen Sagitar has 700mm, the Land Rover Range Rover has 900mm, the Jeep Compass has 800mm, and the Toyota Highlander has 455mm. SUVs generally have higher wading depths than sedans. Generally, when a vehicle wades through water, depending on the depth and the vehicle's characteristics, the owner should take different measures as follows: If the wading depth reaches the exhaust pipe height, it is still safe. Even if water enters the exhaust pipe, the pressure inside can expel the water. As long as the engine is not turned off in the water, water will not flow back into the vehicle. If the wading depth reaches the door frame height, it becomes more dangerous. The vehicle's circuits, electronic components, and sensors are mostly located at the bottom, which could lead to circuit failure, damaging critical electrical components and preventing the vehicle from starting. If the wading depth reaches the air intake height, it is extremely dangerous. Driving directly into such conditions may cause the engine to stall, leading to permanent damage or rendering the engine unusable.
Was this review help?
1
4
Share
DeJoanna
08/13/25 7:39pm
I remember the maximum wading depth of the Dongfeng Mengshi is about 800mm, which means it can easily handle water up to 80cm deep, making it particularly suitable for off-road adventures or driving in rainy conditions. I usually enjoy studying off-road vehicle performance, and wading capability relies on a high ground clearance and sealed engine design. When wading, avoid driving too fast; maintain a steady speed to prevent water from impacting the exhaust system. After wading, it's best to inspect the undercarriage and wheel hubs as soon as possible to remove mud and prevent corrosion of components. Wading depth is a hardcore metric, and the Dongfeng Mengshi is reliable in this aspect, but don't push it by crossing overly deep rivers—safety should always come first. If water enters and damages the engine, the repair costs can be high.
Was this review help?
6
5
Share
Expand All
SanLily
10/08/25 5:14am
I've checked the specifications of the Dongfeng Mengshi, and its maximum wading depth is around 800mm, which is quite impressive for a military-style off-road vehicle. In actual driving, it can handle relatively deep water pits or shallow streams, but you need to pay attention to the water flow direction and ground conditions, such as avoiding rocks that could cause the undercarriage to get stuck. I've driven similar models through water, and the experience was decent. After wading, immediately stop to check for leaks to prevent minor issues from escalating. Wading depth is related to the vehicle's durability, so it's advisable to regularly maintain waterproof components to extend their lifespan. It gives more confidence when driving in the rain, but don't be reckless—if the water exceeds the limit, it's better to take a detour.
Was this review help?
20
5
Share
Expand All
More Forum Discussions

How to Open the Hood of a Toyota Levin?

Toyota Levin hood opening method: There is a release handle under the instrument panel on the lower left side of the driver's seat. After pulling it, the hood will pop up about 1cm. Lift the hood with one hand while reaching inside the grille with the other hand to locate the hood release lever. Detailed information as follows: 1. The Levin hood is made of rubber foam and aluminum foil materials, which reduce engine noise while isolating heat generated by the engine, effectively protecting the hood's paint surface and preventing aging. 2. The Levin is a compact sedan with body dimensions of 4640mm in length, 1780mm in width, and 1455mm in height, with a wheelbase of 2700mm.
4
3
Share

How to Engage Reverse Gear in Santana?

To engage reverse gear in a Santana, first press the gear lever downward from the neutral position, then pull it to the left and push it into the position of first gear. Below are the precautions when engaging reverse gear in Santana: 1. Ensure the vehicle is completely stopped before shifting into reverse. Shifting into reverse while the vehicle is still moving can cause significant damage to the transmission. It can easily lead to gear grinding, so the correct method is to stop the car completely before shifting into reverse for backing up. 2. Fully depress the clutch when shifting into reverse. If the clutch is not fully depressed, gear grinding may occur, which is the harsh sound of gears grinding against each other. Prolonged grinding can wear down the gear teeth, resulting in incomplete gear engagement. To avoid gear grinding, always depress the clutch fully. 3. Maintain a slow speed when reversing and avoid pressing the accelerator. Keep the speed slow and avoid sudden acceleration, especially in automatic transmission vehicles, as it can easily lead to accidents. Therefore, always control the speed carefully when reversing.
10
4
Share

What is the weight of the T-Roc?

The weight of the Volkswagen T-Roc is 1385kg. Taking the 2020 Volkswagen T-Roc as an example, its specifications are as follows: 1. Body dimensions: Length, width, and height are 4318mm, 1819mm, and 1582mm respectively, with a wheelbase of 2680mm. 2. Suspension: Front suspension is MacPherson strut independent suspension, and rear suspension is multi-link independent suspension. 3. Powertrain: Equipped with a 1.4L turbocharged engine, delivering a maximum horsepower of 150ps, maximum power of 110kw, and maximum torque of 250nm, paired with a 7-speed dual-clutch transmission.
17
4
Share

How to Check the Engine Oil in a Jeep Cherokee?

To check the engine oil in a Jeep Cherokee: Open the engine hood. Locate the yellow circular plastic ring (oil dipstick) in the middle-left section of the engine compartment. For accurate measurement, ensure the engine has been turned off for at least 5-10 minutes. Pull out the dipstick, wipe it clean, reinsert it fully, then remove it after 2 seconds. The oil level will be indicated by markings on the dipstick. The Jeep Cherokee is an SUV model with body dimensions of 4649mm (length) × 1859mm (width) × 1686mm (height) and a wheelbase of 2705mm. It features a new aerodynamic exterior design, interior inspired by sacred landscapes, and offers four driving modes (Auto, Sport, Snow, Sand/Mud, and Rock) along with an advanced connected human-machine interaction system.
12
5
Share

How Many Cylinders Does the Changan CS55 Engine Have?

Changan CS55 is equipped with a domestically produced 4-cylinder engine, manufactured at the new passenger vehicle production base in Yuzui. The engine model of Changan CS55 is JL476ZQCD, with a maximum power of 115kw, maximum torque of 225 Nm, and maximum horsepower of 156. For daily maintenance of the Changan CS55 engine, the following methods can be used: Use lubricating oil of appropriate quality grade. For gasoline engines, choose SD--SF grade gasoline engine oil based on the additional devices of the intake and exhaust systems and usage conditions; for diesel engines, select CB--CD grade diesel engine oil according to mechanical load, with the selection standard not lower than the manufacturer's specified requirements; Regularly change the engine oil and filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, performance deteriorates, leading to various engine problems. To avoid malfunctions, change the oil regularly according to usage conditions and maintain an appropriate oil level; When engine oil passes through the fine pores of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter is clogged and oil cannot pass through the filter element, the filter element may burst or the safety valve may open, allowing oil to bypass through the bypass valve, bringing contaminants back to the lubrication areas, accelerating engine wear and increasing internal pollution; Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal powder from component wear to form sludge. Small amounts remain suspended in the oil, while larger amounts precipitate, clogging filters and oil passages, making engine lubrication difficult and causing wear; Regularly use radiator cleaner to clean the radiator. Removing rust and scale not only ensures the engine operates normally but also extends the overall lifespan of the radiator and engine.
19
1
Share

How to Switch Between Low Beam and High Beam?

The operation method for low beam and high beam is: The default position of the car lever is the low beam. Pushing it forward (toward the dashboard) once switches to high beam, and pulling it back (toward the driver) once returns it to low beam. However, this position is not fixed—it maintains the selected beam as long as you hold the lever, and it resets to low beam when you release it. The switching between high and low beams relies on this lever position, which has very light resistance—just a gentle push is enough. Releasing the lever immediately returns it to low beam. Switching between high and low beams is often used as a warning signal. For example, when overtaking using the opposite lane, you can use the beam switch to alert oncoming vehicles. Similarly, during nighttime encounters with other vehicles, switching beams can serve as a reminder.
16
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.