What is the maximum speed limit for turning and U-turns?

2 Answers
McDelilah
07/25/25 9:37am
When turning or making a U-turn, the maximum speed must not exceed 30 kilometers per hour. According to Article 46 of the "Regulations for the Implementation of the Road Traffic Safety Law": "When encountering a U-turn, turning, or descending a steep slope, the maximum speed of a motor vehicle must not exceed 30 kilometers per hour, while for tractors, battery-powered vehicles, and wheeled special machinery vehicles, it must not exceed 15 kilometers per hour." Below is additional information: Relevant regulations: When a motor vehicle passes through an intersection controlled by traffic signals and turns left, it must turn from the left side of the intersection center point. Turn signals must be activated when turning, and low beams must be used when driving at night. At intersections without directional signal lights, turning motor vehicles must yield to straight-moving vehicles and pedestrians. Right-turning motor vehicles from the opposite direction must yield to left-turning vehicles.
Was this review help?
6
3
Share
McSamuel
08/11/25 7:23pm
A few days ago, there was almost an accident at the entrance of my neighborhood because someone turned too fast. According to traffic regulations, the maximum speed for turning or making a U-turn should not exceed 30 km/h. That number might not sound fast, but in reality, it feels quite noticeable when driving. I remember last time driving my friend's old Jetta, even at 20 km/h, the front of the car felt unstable during a turn. Now, driving an SUV with a higher center of gravity, it feels more stable. But no matter how stable, don't speed, especially on rainy days or sharp turns—losing control can easily lead to skidding. The speed shown on the car's speedometer might not even be accurate, so it's safer to glance at the speedometer before turning. Experienced drivers know to slow down in advance when turning, leaving enough reaction time to handle unexpected situations.
Was this review help?
11
1
Share
Expand All
More Forum Discussions

What are the solutions for excessive engine noise?

Here are the detailed causes and solutions for excessive engine noise: 1. The car has been driven for too many years with excessive wear, causing excessive clearance in the transmission system and resulting in vibration and abnormal noise. Solution: Perform a comprehensive overhaul or scrap the vehicle. 2. The transmission V-belt is too loose, causing fluttering or slipping and producing sharp noise. Solution: Adjust the tightness of the transmission V-belt. 3. Excessive carbon deposits in the engine cylinders lead to poor combustion, producing a noise similar to that of a tractor. Solution: Clean the carbon deposits in the cylinders. 4. Check if any bearings are damaged, as damaged bearings will produce a buzzing noise. Solution: Replace the bearings. 5. Poor fuel quality leads to poor combustion, causing the engine to produce a popping noise. Solution: Use high-quality fuel. 6. Excessive engine noise may be related to unsuitable or dirty engine oil. Solution: Change the engine oil.
11
0
Share

How often should the spark plugs in a Volvo V40 be replaced?

The spark plugs in a Volvo V40 generally need to be replaced every 60,000 kilometers. Under normal maintenance conditions, car spark plugs should be replaced after driving 40,000 to 60,000 kilometers. However, this may vary depending on the brand and engine, so it is recommended to follow the user manual. The following standards can be used as a reference for maintenance and replacement: platinum spark plugs should be replaced at 40,000 kilometers, standard nickel alloy spark plugs at 20,000 kilometers, and iridium spark plugs at 60,000 to 80,000 kilometers. Steps for replacing spark plugs: Open the hood, lift the plastic cover of the engine, and remove the high-voltage ignition wires. Mark each cylinder's position to avoid confusion. Use a spark plug socket to remove the spark plugs one by one. While removing them, check for any external debris like leaves or dust and ensure everything is cleaned thoroughly. Place the new spark plugs into the spark plug holes, hand-tighten them a few turns, and then use the socket to tighten them further. Reinstall the high-voltage ignition wires in the correct firing order and reattach the cover.
11
5
Share

How to Remove Overspray from Car Body?

For overspray that has not completely dried, you can spray cleaner on the overspray and wipe it off with a towel; for dried overspray, you can use 2000-grit polishing sandpaper to grind off the overspray on the paint surface. Below are specific methods for dealing with overspray on cars: 1. For overspray that has not completely dried, spray cleaner on the overspray and wipe it with a soft towel. After wiping the entire car, use detailing clay to scrub the paint surface. 2. For dried overspray, first wash the car thoroughly, then use 2000-grit polishing sandpaper to grind off the overspray on the paint surface. After that, perform a polishing treatment to restore the gloss of the paint surface, and finally, carry out a full paint surface maintenance. The vehicle's paint consists of four layers: the electrocoat layer, the primer layer, the basecoat layer, and the clearcoat layer. The electrocoat layer serves to prevent rust and enhance the adhesion of the paint layers. The primer layer connects the basecoat layer and the electrocoat layer. The clearcoat layer is the outermost layer of the paint, primarily functioning to enhance the paint's gloss, improve texture, protect against UV rays, and prevent minor scratches.
11
5
Share

How often should the transmission fluid in the Jade be changed?

The transmission fluid in the Jade should be changed every two years or after driving 40,000 kilometers. The method for changing the transmission fluid in a car is as follows: 1. First, lift the car and place a large container underneath to catch the used fluid. Use an appropriate screwdriver to remove the inner and outer covers of the transmission, being cautious as some transmission fluid may spill out. 2. After a few minutes, when most of the fluid has drained, carefully remove the last oil pan, ensuring to support it by hand as it still contains a significant amount of used fluid. Upon removal, you will notice residue at the bottom of the oil pan. 3. Carefully remove the transmission fluid filter, which will clearly reveal the solenoid valve controlling gear shifts. 4. Remove the oil pan gasket and clean the surrounding area. If there are hard-to-reach spots, use tools for thorough cleaning. Over time, the rubber on the gasket may stick to the machine edges, requiring a small scraper and carburetor cleaner for easier and more thorough removal. 5. Wipe all cleaned transmission fluid filtration components with cotton cloth and reinstall them. Filters are generally for one-time use, so replace them along with the new fluid and gasket during the oil change.
3
4
Share

Is it necessary to clean the three-way catalytic converter of the New Transit?

The three-way catalytic converter generally does not need cleaning. The failure rate of the three-way catalytic converter is very low, and cleaning is typically done using a no-disassembly method similar to an IV drip. Usually, the three-way catalytic converter should be inspected and cleaned as needed every 30,000 kilometers. It is advisable to clean the three-way catalytic converter whenever the fuel injectors, throttle, and intake tract are serviced. Additionally, it is best to clean the three-way catalytic converter before the annual vehicle inspection to ensure smooth passage of the emissions test. When fuel quality is poor, sulfur, phosphorus, lead, and manganese-containing anti-knock agents in the fuel can form chemical complexes inside the three-way catalytic converter after combustion. Due to its honeycomb structure, the three-way catalytic converter is prone to clogging. The use of manganese-containing anti-knock agents in fuel, sulfur- and phosphorus-containing antioxidants in lubricants, and traffic congestion can easily lead to poisoning, failure, or clogging of the three-way catalytic converter. As a critical component of automotive exhaust treatment, the three-way catalytic converter significantly reduces pollutants in vehicle emissions, and all exhaust gases must pass through it. If the three-way catalytic converter is damaged or clogged, it is similar to a blocked exhaust pipe, resulting in a noticeable decrease in vehicle power, increased fuel consumption, and severe exhaust pollution.
18
3
Share

What Does the Number of Axles on a Vehicle Mean?

The function of the number of axles on a vehicle is to bear the load of the vehicle and maintain its normal operation on the road. Vehicles are categorized by the number of axles: single axle, double axle, front four rear four, front four rear eight, semi-trailer for more axles, two-axle tractor with three-axle trailer, three-axle tractor with three-axle trailer. Below are the applications of vehicle axle counts: 1. Ordinary family cars generally use a single axle. 2. For highway transport vehicles with a total mass less than 19 tons and vehicles not subject to road or bridge axle load limits, such as mining dump trucks, a simple and cost-effective two-axle configuration is typically used. 3. Highway transport vehicles with a total mass between 19-26 tons adopt a three-axle configuration, while vehicles with even greater total mass should use four or more axles. 4. Generally, three-wheeled trucks have a capacity of 2 tons; low-speed trucks (four wheels with a maximum design speed less than 70 km/h) 4.5 tons; two-axle trucks 17 tons; three-axle trucks 25 tons (27 tons for vehicle combinations consisting of a two-axle vehicle and a one-axle trailer); four-axle trucks 35 tons; five-axle trucks 43 tons; six-axle and above trucks 49 tons.
10
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.