What is the maximum speed limit for cars on highways in kilometers per hour?

1 Answers
MaddoxDella
07/25/25 3:19am
The "Regulations for the Implementation of the Road Traffic Safety Law of the People's Republic of China" Article 78 stipulates that highways shall indicate the driving speed of lanes, with the maximum speed not exceeding 120 kilometers per hour and the minimum speed not less than 60 kilometers per hour. Special speed limit situations during high-speed driving: When encountering complex road sections, speed limit signs will be posted at both ends of the highway, such as tunnel speed limits of 80km/h or certain road sections with interval speed limits of 80km/h. Therefore, drivers need to constantly observe road signs while driving. Precautions for driving on highways: Maintain a constant speed while driving; Try to stay in one lane and avoid changing lanes arbitrarily; When overtaking, be decisive and pay attention to whether there are obstacles in the overtaking lane ahead; Drive cautiously at night, use high beams as much as possible, watch for taillights of vehicles ahead, and avoid fatigued driving; Overcome adverse weather conditions; If temporary parking is required due to a malfunction, turn on the right turn signal in advance to leave the driving lane, park in the emergency stopping lane or on the right shoulder, and do not stop on the driving lane. At the same time, turn on the hazard lights and place a warning sign 150 meters behind the vehicle; Do not exceed the speed limit.
Was this review help?
3
2
Share
More Forum Discussions

How to fix a broken door handle?

Use a flathead screwdriver to gently pry open the lock cylinder decorative cover. Remove the rubber gasket, open the car door, pry off the rubber gasket, and use a spline wrench to remove the door handle lock block screws. Remove the small round cover, then use a small flathead screwdriver to pry along the edge gap between the lock block and the door panel, gradually disassembling the door handle lock block. Hold the door handle with your left hand, then pull backward to separate the door handle from the door panel. Disconnect the wiring harness connector and remove the door handle. Replace with a new door handle, then reassemble the components in reverse order.
13
0
Share

What to Do When the Window Weatherstrip is Lifted?

Open the car door, and you will find a small black cover on the edge of the door. This black cover serves as a decoration and needs to be removed. After removing the small black cover, you will find the screw that secures the outer window weatherstrip. Use a T-20 spline to remove this screw. Take out a large flathead screwdriver and gently pry the edge of the outer window weatherstrip to loosen it slightly. Use your fingers to hold the outer window weatherstrip, then gently pull it upward to separate it. After removal, replace it with a new one.
15
1
Share

What are the consequences of not collecting the license after passing Subject 4?

The consequence of not collecting the license after passing Subject 4 is that you will be considered as driving without a license when driving on the road. Here are the relevant details: 1. Pre-license ceremony: Before receiving the driver's license, driving school students will participate in a solemn and formal collective oath-taking activity organized by the examination center police, emphasizing civilized and lawful driving. This serious and ceremonial group oath activity helps students truly understand that obtaining a driver's license means taking on significant social responsibilities and deeply recognizing that civilized and lawful driving is a concrete manifestation of caring for family and cherishing life. 2. Impact: If a driver does not carry a motor vehicle driver's license that matches the type of vehicle they are driving, it should be regarded as driving without a license.
14
4
Share

How long can the clutch be pressed in Subject 3 before failing?

In Subject 3, generally pressing the clutch for 5 seconds will result in failure. Below are the relevant details: 1. Introduction: When the clutch is fully depressed, it should not exceed 5 seconds. The clutch in a semi-engaged state should not exceed 15 seconds. The time when the clutch is pressed during a stop is not counted. If you feel the clutch has been pressed for too long, you can fully depress it and then slowly release it to the semi-engaged state, which will reset the system's timing. 2. Additional Information: Subject 3 includes the road driving skills test and the safety and civilized driving knowledge test. It is part of the motor vehicle driver's license assessment and is the abbreviated term for the road driving skills and safety and civilized driving knowledge test subjects in the motor vehicle driver's test. The content of the road driving skills test varies for different types of vehicles eligible for driving.
4
5
Share

What does etcpwr mean?

PWR on the car dashboard stands for Powertrain, also known as Powerplant in English. It refers to a series of components in the vehicle that generate power and transmit it to the road surface. The electronic throttle control system proportionally adjusts to the accelerator opening under all driving conditions, ensuring the engine output power remains appropriate. The electronic throttle control system has three modes. Here is some relevant knowledge about the electronic throttle control system: 1. Normal Mode: Recommended for ordinary driving to save fuel. 2. Power Mode: Used to enhance acceleration and for sporty driving. 3. Snow Mode: Used for slippery road conditions such as ice and snow. In this mode, the rotation of the rear wheels is appropriately controlled.
5
3
Share

What kind of oil should be used for the automatic transmission of Toyota Levin Hybrid?

Toyota Levin Hybrid's automatic transmission requires the use of Toyota's dedicated transmission oil. Below are the relevant details: 1. Dedicated transmission oil: The Toyota Levin Hybrid's automatic transmission requires the use of dedicated automatic transmission oil. Transmission oil is a consumable item that changes over time. It serves to clean, lubricate, and seal the transmission, provides some cooling function, and also supplies hydraulic pressure. 2. Flushing machine: The flushing machine uses pressure to push out the old oil with new oil, simultaneously adding new oil and extracting the mixed old and new oil. The downside of this method is that it consumes more oil, resulting in higher replacement costs and expenses. However, it is more effective and particularly suitable for automatic transmissions.
14
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.