What is the material of the Besturn X80 spark plug?

1 Answers
StBraxton
07/29/25 1:23pm
The Besturn X80 spark plug is made of platinum, and the brand is NGK. The spark plug is an important component of the gasoline engine ignition system. It introduces high voltage electricity into the combustion chamber and causes it to jump across the electrode gap to generate a spark, thereby igniting the combustible mixture in the cylinder. The main types of spark plugs include: standard spark plugs, insulator projection spark plugs, electrode spark plugs, seat spark plugs, pole spark plugs, and surface gap spark plugs. Replacement cycle for spark plugs: Under normal maintenance conditions, they should be replaced after driving 40,000 to 60,000 kilometers. However, this may vary depending on the brand and engine. It is recommended to follow the user manual. You can refer to the following standards for maintenance and replacement: platinum spark plugs should be replaced at 40,000 kilometers, ordinary nickel alloy spark plugs at 20,000 kilometers, and iridium spark plugs at 60,000 to 80,000 kilometers.
Was this review help?
4
3
Share
More Forum Discussions

What does AUX mean in a car?

AUX is an audio input interface. The basic working principle of the AUX interface is that after connecting to the AUX interface, the audio from electronic devices can be transmitted through the headphone jack and AUX interface to the car audio system, allowing the audio to be played through the car's audio broadcasting facilities. The USB interface can be used to insert a USB drive for audio playback. To use it, connect one end to the AUX interface and the other end to a mobile phone, MP3, MP4, or other video player. This allows you to listen to songs or niche music anytime, anywhere, without being limited to car music CDs. However, if the playback device runs out of power, the music will stop (the interface is typically a 3.5mm standard headphone jack). Aux is short for Auxiliary, which refers to an additional signal line design. In general audio equipment, besides the standard output and input terminals, there are often several terminals labeled Aux, serving as backup connection points. These can be used for special applications, such as additional audio output or input. These backup terminals or lines, whether for input or output, are collectively referred to as Aux. Function: The AUX port is an asynchronous port, mainly used for remote configuration, dial-up connections, or connecting to a MODEM via a transceiver. It supports hardware flow control. The AUX port is usually placed alongside the CONSOLE port because they are used in different configuration environments. The AUX interface establishes a command-line connection between the user and the device, enabling operations that are typically impossible in user mode, such as initialization, restoring default configurations, or correcting abnormal user modes. It provides a fixed port for the device, which can be used as a standard asynchronous serial port with a maximum speed of 115200bit/s. Using the AUX interface, remote configuration and line backup for hardware products can be achieved. Note: When using the AUX interface, ensure you purchase the correct connecting cable and avoid plugging the audio cable into the wrong port. It's best to follow the steps outlined in the product's user manual. If you're unsure, consult the product's official website or call customer support for guidance.
19
4
Share

How to Tell If Engine Oil Level is Increasing?

Methods to check for increased engine oil level: 1. Park the car on a relatively flat surface, turn off the engine and wait for more than five minutes to allow the oil to completely flow back. It is recommended to perform the measurement at the same parking spot each time; 2. Open the engine compartment, locate the oil dipstick, pull it out, and check if the oil level is between the two marks on the dipstick; 3. To ensure accuracy, first wipe the dipstick clean with a paper towel, then reinsert it into the engine. Oil level increase commonly occurs in direct injection engines and is often observed during winter. In direct injection engines, fuel is directly injected into the cylinder, unlike port fuel injection where there is more time for the fuel to mix with air. Some fuel may be sprayed onto the cylinder walls, causing wetting.
18
2
Share

Where is the VIN number located on a smart car?

smart car's VIN number is located at the lower right corner of the front windshield. For vehicle inspection purposes, the VIN to be imprinted should be found in front under the front passenger seat - just lift the panel to locate it. The VIN (Vehicle Identification Number) is a unique 17-character alphanumeric code that identifies a vehicle's manufacturer, engine, chassis number, and other specifications. smart is a microcar brand under Mercedes-Benz, with dimensions of 2695mm in length, 1663mm in width, and 1555mm in height, featuring a wheelbase of 1873mm. In terms of suspension, the smart car uses MacPherson strut independent suspension at the front and torsion beam semi-independent suspension at the rear.
18
1
Share

How to adjust the time on Chery QQ3?

Chery QQ3 time adjustment method: 1. Press and hold the SEL button for 2 seconds until SET flashes to enter the setting mode, then briefly press both SEL and TRIP buttons simultaneously to enter clock initialization mode; 2. When the clock flashes, press the TRIP button to adjust the hour value. After setting the hour, press SEL to enter minute adjustment mode, then use TRIP to adjust minutes; 3. After completing adjustments, briefly press both SEL and TRIP buttons simultaneously to finish time setting. The Chery QQ3 is a microcar under Chery Automobile, with dimensions of 3550mm in length, 1495mm in width, and 1485mm in height, featuring a 2340mm wheelbase. For suspension, the front adopts MacPherson strut independent suspension while the rear uses longitudinal trailing arm semi-independent suspension.
17
4
Share

How to Steer the Wheel When Driving on Curves?

Steering techniques for curve driving: 1. When entering a left curve, keep the vehicle close to the right line before turning the wheel to the left; 2. When entering a right curve, keep the vehicle close to the left line before turning the wheel to the right; 3. When the right front corner of the car touches the right line, turn the wheel one full turn to the left, keeping the left front corner at a certain angle to the line on the ground to follow the right line of the first S-curve, preventing the car from crossing or touching the line; 4. When exiting a left curve, turn the wheel half a turn to the right as the front wheels just leave to avoid the rear wheels touching the line; 5. When exiting a right curve, turn the wheel half a turn to the left as the front wheels just leave to avoid the rear wheels touching the line.
11
0
Share

Which Mazda models feature rotary engines?

Mazda models equipped with rotary engines belong to the RX series, while other models do not utilize this engine type. The rotary engine offers advantages such as achieving high RPMs without requiring precise crankshaft balancing, compact size, lightweight construction, and significantly simplified architecture. Taking the Mazda RX7 as an example: The Mazda RX7 is a sports car under the Mazda brand, with dimensions of 4430mm in length, 1770mm in width, and 1340mm in height. In terms of power, the Mazda RX7 is equipped with a twin-turbocharged 13B-REW rotary engine, delivering a maximum output of 195 kW and peak torque of 294 Nm, paired with a 5-speed manual transmission.
2
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.