What is the load capacity of Foton Times M3?

1 Answers
BenjaminLynn
07/30/25 10:31am
Foton Times M3 has a rated load capacity of approximately 2.7 tons. Below is an introduction to Foton M3: 1. Exterior: Its length, width, and height are 5995mm, 2150mm, and 2370mm respectively, with a front wheelbase of 1715mm and a rear wheelbase of 1590mm. The cab width is 1995mm, featuring a single-row seat configuration with a capacity for 3 people and equipped with a manual sunroof. 2. Interior: The interior offers a new car-like experience, with multiple car-like module designs that are relatively refined. The seats have improved materials and angles, effectively reducing driver fatigue. The interior space is spacious, and the doors use positive pressure sealing for better noise insulation. 3. Engine: The engine used is the Foton Cummins ISF2.8s5F130 model, compliant with China National V emission standards. This engine has a maximum power of 96 kW, torque of 315 N·m, and a rated speed of 2900 RPM, paired with a WLY5G32 transmission from Wanliyang.
Was this review help?
11
5
Share
More Forum Discussions

How to resolve the C1035 fault code?

If the brake system warning light is illuminated in your car, it may indicate a potential issue with the anti-lock braking system (ABS). It is recommended to visit an auto repair shop and use an automotive diagnostic scanner to inspect the ABS system and read the fault code. Once the issue is identified, proceed with the necessary repairs based on the fault content. If it is an intermittent fault, use the automotive diagnostic scanner to clear the fault code.
5
3
Share

How to start a C2 automatic transmission car?

Turn on the turn signal switch and activate the left turn signal. Press the brake pedal, shift the transmission lever to "D" gear, honk the horn once, and release the handbrake. Observe the traffic conditions in front and behind again, making sure to check the left rear traffic situation through the left rearview mirror. Slowly release the brake pedal, gently press the accelerator pedal, and after starting onto the driving lane, turn off the turn signal by switching back the turn signal switch.
3
4
Share

How to Solve the Problem of Loud Tire Noise in CRV?

If it is tire noise, it is recommended to replace them with Michelin silent tires. If it is a new car and the noise feels very loud, you can add some sound insulation to the vehicle. The engine noise of the new model is a bit loud when accelerating, so you can go to a car decoration shop to explore some noise reduction modifications.
14
0
Share

How to Set Up Automatic Mirror Tilt When Reversing in CR-V?

Power on the vehicle but do not start the engine (press the start button without stepping on the brake). Select the side mirror you want to set by pressing the mirror adjustment selection button (left or right). Step on the brake, shift to R (Reverse) gear, and the selected mirror will automatically tilt down to the factory preset position. Adjust it to your desired position using the adjustment buttons. Press and hold the seat memory button (1, 2, or 3) for about 2 seconds, step on the brake, shift to P (Park) gear, and press the mirror adjustment selection button once more to complete the setup.
13
3
Share

How to activate the automatic window roll-up feature when locking the CT4?

The one-touch window control button is located on the door next to the driver's seat. Press the button upwards to the first stop, and release it when the window reaches the desired position. Briefly pull the switch to the second stop to automatically roll up the window.
12
1
Share

How to view the dashcam footage on C260L?

Press this button to enter the settings interface. In the recording interface, a short press can also turn the sound on or off. When powered off, press once to turn on. When powered on, press and hold to turn off. Switch between three functions: photo, video, and playback. In the video interface, this button can also be used to enable the forced save function. Downward selection in the menu bar is for lens zoom-out (4/3/2/1x). Upward selection in the menu bar is for lens zoom-in (1/2/3/4x). Use this button to turn the recording function on or off. Some dashcams also use the [OK] button instead.
2
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.