What is the license plate area code for Zhe L?

Which Turn Signal to Use When Making a Right U-turn?

When making a right U-turn, the right turn signal should be activated. For a left U-turn, the left turn signal should be used. According to Article 57 of the Implementation Regulations of the Road Traffic Safety Law, motor vehicles must use turn signals as follows: Activate the left turn signal in advance when turning left, changing lanes to the left, preparing to overtake, leaving a parking spot, or making a U-turn. Activate the right turn signal in advance when turning right, changing lanes to the right, returning to the original lane after overtaking, or parking by the roadside. When approaching sharp curves, hilltops, or other sections with limited visibility that affect safety, or when overtaking or encountering emergencies, motor vehicles should slow down and sound the horn as a warning. Article 58: When driving at night without streetlights, under poor lighting conditions, or in low visibility situations such as fog, rain, snow, dust, or hail, motor vehicles must turn on their headlights, position lights, and tail lights. However, high beams should not be used when following another vehicle closely in the same direction. During foggy conditions, motor vehicles must also turn on their fog lights and hazard warning lights.

16

0

Share

What to Do When a Motorcycle Won't Start After Long-Term Storage?

Methods for starting a motorcycle that has been stored for a long time: Due to prolonged disuse, the gasoline in the carburetor evaporates and deteriorates, clogging the carburetor's jets. A thorough and careful cleaning of the carburetor should resolve the issue. Reasons why a motorcycle won't start: 1. Carburetor issues, typically due to prolonged use. 2. Spark plug problems, sometimes caused by fuel flooding the plug. 3. Weather conditions. For example, cold winter weather can make it difficult to start. 4. Frequent use of the electric starter can drain the battery if the motorcycle doesn't start, potentially damaging the battery. 5. Idle speed issues. Sometimes, failure to start may be due to low idle speed. In summer, the idle speed should be adjusted so the tachometer needle points to one mark or slightly more, while in winter, it should be adjusted to one and a half marks or below two.

9

1

Share

What is the appropriate RPM for an automatic transmission car?

Automatic transmission engine speed is between 1800 and 2000 RPM. Steps to start an automatic transmission car: 1. Insert the key into the ignition and turn it to the second position (power mode), then wait for the system self-check to complete. 2. Shift the gear lever from P (Park) to N (Neutral). 3. Release the brake and start the car's engine. 4. Press the brake pedal with your foot, shift the gear lever from N to D (Drive), then release the brake and press the accelerator to start moving. Engine maintenance methods: 1. Use high-quality engine oil. 2. Use qualified coolant. 3. Regularly clean the radiator scale. 4. Periodically remove carbon deposits from the engine. 5. Replace the vehicle's air filter, oil filter, and fuel filter on time. 6. Check the condition of the spark plugs. 7. Maintain normal RPM levels.

13

3

Share

How to Check Vehicle Pulling to One Side?

Vehicle pulling to one side can occur in the following two situations: 1. During straight-line driving at a constant speed, the vehicle drifts to one side when the steering wheel is released; 2. The vehicle can maintain a straight path without drifting, but the steering wheel is not centered. The causes of vehicle pulling to one side are as follows: 1. Uneven tire pressure between the upper and lower tires. Different pressures result in inconsistent tire circumferences, causing the vehicle to pull toward the side with lower pressure. If the pulling is significantly due to tire pressure, it can often be detected visually. 2. Incorrect toe alignment. Wheel toe alignment primarily refers to the camber angle of the front wheels. Simply put, proper toe alignment creates a "front narrow, rear wide" trumpet shape for the front wheels. Incorrect toe alignment usually results in a "front wide, rear narrow" shape. This issue is often caused by impacts to the front suspension or excessive gaps in suspension links or ball joints. While the primary solution is a four-wheel alignment, the suspension system must first be in good condition. 3. Brake system malfunction. Although brake-related pulling (mainly from the front brakes) is quite subtle, it should be carefully prevented. The most common brake system issue is the front brake caliper not retracting smoothly, which creates resistance to wheel movement.

16

3

Share

Is a Hybrid Vehicle Issued a Green License Plate or a Blue One?

Plug-in hybrid vehicles require green license plates, while conventional hybrid vehicles use blue license plates. A plug-in hybrid electric vehicle (PHEV) is a type of new energy vehicle that bridges the gap between pure electric vehicles and traditional fuel-powered cars. It features both the conventional car components—such as the engine, transmission, drivetrain, fuel lines, and fuel tank—and the electric vehicle elements, including the battery, electric motor, and control circuitry. Conventional hybrid vehicles, on the other hand, are equipped with a drivetrain that combines two or more individual power systems capable of operating simultaneously. The driving power is supplied by either system alone or collectively, depending on the actual driving conditions. Below are the key differences between plug-in hybrids and conventional hybrids: Power Supply Method: Plug-in hybrids are characterized by their ability to charge via an external power source, much like pure electric vehicles, whereas conventional hybrids do not require charging. Battery and Fuel Tank Roles: Plug-in hybrids have larger batteries and smaller fuel tanks, primarily relying on the battery for propulsion. In contrast, conventional hybrids feature smaller batteries and larger fuel tanks, with the internal combustion engine serving as the main power source. The battery only provides energy during initial acceleration.

4

Share

What are the speed grades for cold running-in after an engine overhaul?

Cold running-in starts at a speed of 400r/min to 600r/min and ends at 1000r/min to 1200r/min. The following is an introduction to the engine: 1. Introduction: An engine is a machine that can convert non-mechanical energy into mechanical energy. 2. Classification: Includes internal combustion engines, external combustion engines, jet engines, electric motors, etc.

13

0

Share

What is the license plate area code for Zhe L?

Which Turn Signal to Use When Making a Right U-turn?

What to Do When a Motorcycle Won't Start After Long-Term Storage?

What is the appropriate RPM for an automatic transmission car?

How to Check Vehicle Pulling to One Side?

Is a Hybrid Vehicle Issued a Green License Plate or a Blue One?

What are the speed grades for cold running-in after an engine overhaul?

Can You Start a Car While the Battery Is Charging?

What to Do When a Truck's Brakes Pull to One Side?

How often should the transmission fluid be changed for a K2?

What size tires can be installed on 16-inch rims?