···
Log in / Register

What is the length of the Honda Avancier?

4 Answers
LeCharlie
07/29/25 10:29pm

The length of the Honda Avancier is 4816mm, width is 1942mm, height is 1669mm, and the wheelbase is 2820mm. Taking the 2019 Honda Avancier as an example, it is a mid-size SUV with a fuel tank capacity of 57 liters, trunk capacity of 510 liters, and a curb weight of 1712kg. The 2019 Honda Avancier features a front MacPherson strut independent suspension and a rear multi-link independent suspension, with a front-wheel drive layout. It is equipped with a 1.5T inline 4-cylinder turbocharged engine, delivering a maximum horsepower of 193PS, maximum torque of 243Nm, and maximum power of 142kW, paired with a continuously variable transmission (CVT).

Was this review help?
11
0
Share
VanWyatt
08/15/25 11:19pm

As an automotive enthusiast, I frequently check the dimensional parameters of the Avancier. Its total length is 4855 millimeters, approximately 4.86 meters. This measurement is based on the overall vehicle length, taken from the farthest point of the front bumper to the rear bumper. Why is this important? The vehicle length directly impacts daily usability, such as whether there's sufficient parking space, especially on narrow city streets or in underground garages. As a midsize SUV, the Avancier's length, combined with its 2820mm wheelbase, provides comfortable rear seating space and luggage compartment volume, making it suitable for family road trips. Compared to other models, like the Toyota Highlander at 4950mm, the Avancier is slightly shorter but easier to maneuver; the Volkswagen Tiguan L is about 4712mm, making the Avancier over 100mm longer, which translates to a more spacious interior. Before purchasing, it's advisable to measure your parking space to ensure it meets your needs, and also consider the impact of aerodynamic drag on fuel consumption. In summary, knowing the exact length can enhance your driving experience and help avoid unexpected scrapes.

Was this review help?
14
0
Share
Expand All
ZoeDella
10/18/25 3:12am

As an Avancier owner, the 4855mm length of my car has brought many impacts to my daily life. When parking, this size makes the garage feel a bit cramped, especially when turning in old residential areas, I often have to drive slowly and carefully. However, it became much easier after equipping the automatic parking system. The long wheelbase means super spacious rear seats that can comfortably accommodate three adults, and the trunk can fit two large suitcases plus a stroller during family trips, which is extremely practical. For urban commuting, the length provides greater stability at high speeds compared to smaller sedans. I remember measuring my parking space before purchase - about 5 meters long, leaving just enough room. Friends' cars like the Highlander are longer, but our Avancier strikes a perfect balance between size and presence. I'd recommend new owners practice reversing skills more or use assistive devices to handle the challenges - while the length might be slightly troublesome, the space advantages absolutely make it worthwhile.

Was this review help?
14
0
Share
Expand All
Wright
12/01/25 3:52am

From a design perspective, the Crown's 4855mm length optimizes interior layout and driving balance. Dimensions affect space allocation, allowing rear passengers to stretch their legs comfortably, while the 2820mm wheelbase reduces sway during turns. Aerodynamic drag coefficient was also considered during design, keeping fuel consumption around 8-9L/100km; longer than compact SUVs like the CR-V's 4620mm, yet avoiding the bulkiness of full-size models. Both safety and handling benefit from this—high body rigidity improves crash absorption, though requiring more parking space allowance.

Was this review help?
14
4
Share
Expand All
More Forum Discussions

how to learn to paint cars

Learning to paint a car properly is a multi-step process that requires patience, practice, and a significant investment in the right equipment and safety gear. The core skill involves mastering surface preparation, priming, applying basecoat color, and finishing with a clear coat. While a basic single-stage paint job can be a DIY project for a hobbyist, achieving a showroom-quality finish with a modern basecoat/clearcoat system often requires professional training. Essential Equipment and Safety Your first investment must be in safety. A respirator with organic vapor cartridges and a full-face shield is non-negotiable to protect against isocyanates found in clear coats, which are hazardous. You'll also need a dedicated, well-ventilated space like a spray booth or a clean, dust-free garage. The core tool is a High-Volume Low-Pressure (HVLP) spray gun , which is more efficient and user-friendly than older models. You'll also need sanders, tack cloths, mixing cups, and a moisture trap for your air compressor. The Critical Steps: More Than Just Spraying The secret to a great paint job is 90% preparation. Any flaw in the bodywork or existing paint will be magnified by the new paint. Disassembly and Prep: Remove trim, handles, and lights. Then, strip the car to bare metal or thoroughly scuff the existing paint to create a "tooth" for the new primer to adhere to. Bodywork and Sanding: Fix dents with body filler. This stage demands patience to get the panels perfectly straight. You'll progress through various grits of sandpaper (e.g., 180 to 400 grit) to create a smooth surface. Priming: Primer seals the surface and provides a uniform base for the color. After spraying, it must be sanded again with finer grits (like 600-800 grit) until it feels like glass. Painting (Basecoat): Apply the color coat in several thin, even "mist coats" and "wet coats," avoiding runs. Proper gun technique—maintaining a consistent distance and speed—is crucial. Clear Coat: This transparent layer provides depth and gloss. It's applied wetter than the basecoat and requires a controlled environment to avoid dust contamination. Paths for Learning Consider a vocational program at a technical school for the most direct path to a career. For DIY learners, start with small projects like a motorcycle fender or a tool cabinet. Online video tutorials from reputable automotive paint suppliers are invaluable, but they are no substitute for hands-on practice. Aspect DIY/Hobbyist Approach Professional Training Time Investment Evenings/Weekends; project can take weeks 6-18 month focused program Cost (Approx.) $1,500 - $3,000 for quality starter equipment $5,000 - $15,000+ for tuition Best For Restoring a classic car, customizing a personal vehicle Pursuing a career in collision repair or custom painting Typical Outcome Good to very good finish on personal projects Factory-quality, consistent, commercial-grade finishes Key Skill Focus General technique, problem-solving on one project Speed, efficiency, mastery of materials for various jobs
9
1
Share

how to pass car inspection

To pass a car inspection, the key is preparation. Don't just hope your car passes; proactively check and address common failure points like check engine lights , worn windshield wipers, and non-functional exterior lights (headlights, brake lights, turn signals). Most inspections focus on safety and emissions, so ensuring these basic systems are in good working order drastically increases your chances of success. Start by checking your state's specific requirements, as they vary significantly across the U.S. The most common reason for failure is an illuminated Check Engine Light (CEL) . This light indicates the car's computer has detected a problem with the engine or emissions system. Even if the car seems to run fine, a lit CEL is an automatic failure in most states. Use an OBD-II scanner to read the trouble codes, which can point you toward the necessary repair, whether it's a loose gas cap or a faulty oxygen sensor. Exterior Lights and Indicators are a quick and easy check. Have a friend walk around the car while you operate the headlights (low and high beams), brake lights, turn signals, and hazard lights. Replace any dead bulbs immediately. Don't forget the license plate light. Tire tread depth is a critical safety check. The legal minimum is 2/32 of an inch. You can use a tread depth gauge or the classic "penny test" (insert a penny upside-down into the tread; if you can see the top of Lincoln's head, your tread is too low). Also, check for uneven wear, which could indicate an alignment issue. Windshield and Wipers must be in good condition. Any large cracks or chips directly in the driver's line of sight will likely cause a failure. Your wiper blades should effectively clear the windshield without streaking. Here’s a quick pre-inspection checklist with common failure points and their typical repair costs to help you budget: Pre-Inspection Check Item Common Reason for Failure Typical DIY Fix Cost Typical Professional Repair Cost Check Engine Light Loose gas cap, faulty O2 sensor $15 (new gas cap) $150 - $400+ Brake Light Bulb Burnt-out bulb $5 - $15 (per bulb) $30 - $75 Tire Tread Depth Worn below 2/32" N/A (replacement needed) $100 - $200 per tire Windshield Wiper Blades Worn, streaking blades $15 - $30 (pair) $40 - $60 (installation) Turn Signal Bulb Burnt-out bulb $5 - $15 (per bulb) $30 - $75 Exhaust Smoke (Blue/Black) Burning oil or fuel Requires diagnostic $500 - $2,000+ Brake Pad Thickness Worn below minimum spec $50 - $100 (per axle) $150 - $300 (per axle) Finally, if your state requires an emissions test , it's a good idea to take your car for a 20-30 minute drive on the highway before the inspection. This gets the catalytic converter and engine up to optimal operating temperature, which can help the car pass the tailpipe or OBD-II emissions check.
15
3
Share

how to open car front hood

Opening your car's front hood is a straightforward process that typically involves two steps: releasing the interior latch and then disengaging the secondary safety catch under the hood itself. The most common method is to pull a lever located inside the passenger cabin, usually beneath the dashboard on the driver's side or to the side of the driver's footwell. Once you hear the hood pop, you'll need to go to the front of the car, slide your hand under the slightly raised hood to feel for a secondary release lever, often in the center, and push or lift it to fully open the hood. The exact location of the interior release lever can vary significantly between car models. In most sedans and SUVs, you'll find it on the lower left side near the door. In some vehicles, particularly certain European brands, it might be located closer to the center console or even in the glove compartment. If you cannot find it, your owner's manual is the most reliable resource, as it will have a diagram specific to your vehicle. After releasing the interior latch, the hood will pop up a few inches but remain secured by the safety catch. This is a crucial feature designed to prevent the hood from flying open while driving. Walk to the front of the car and locate the release mechanism under the center of the hood. You often need to feel for a small lever or button. You may need to push it to the side or lift it up while simultaneously raising the hood. Most hoods are supported by a prop rod, which you must lift out of its clip and place into the designated slot on the underside of the hood to hold it securely open. For reference, here is a summary of common release lever locations across different vehicle types: Vehicle Type Common Interior Latch Location Safety Catch Type Sedan (e.g., Toyota Camry) Lower left kick panel near door Center-lever, push to the side SUV (e.g., Ford Explorer) Footwell, left of the brake pedal Center-latch, lift up Sports Car (e.g., Chevrolet Corvette) Often located in the passenger footwell Button-release, push inward Luxury Vehicle (e.g., Mercedes-Benz) Sometimes within the glove box Lever, pull downward Electric Vehicle (e.g., Tesla Model 3) Accessed via the central touchscreen Manual release may be behind frunk badge Always ensure the vehicle is parked on a level surface, the parking brake is engaged, and the engine is cool before attempting to open the hood. If you encounter significant resistance, do not force it, as you may have missed the secondary latch.
11
1
Share

how to jump battery in car

To jump-start a car, you need a set of jumper cables and another vehicle with a good battery. The core process involves connecting the cables in a specific, safe sequence to transfer power from the good battery to the dead one. The most critical rule is to avoid connecting the negative cable to the dead battery's negative terminal directly; instead, you must ground it to an unpainted metal surface on the dead car's engine block to prevent sparking near the battery, which could ignite flammable hydrogen gas. Step-by-Step Guide: Position the Cars: Park the working car close to the one with the dead battery, but ensure they are not touching. Turn off both engines, set the parking brakes, and put both cars in "Park" (or "Neutral" for a manual transmission). Identify Terminals: Open both hoods and locate the batteries. Identify the positive (+) and negative (-) terminals on each. Clean off any major corrosion if present. Connect the Cables in THIS Order: Red Clamp to Dead: Attach one red (positive) clamp to the positive terminal of the dead battery. Red Clamp to Good: Attach the other red clamp to the positive terminal of the good battery. Black Clamp to Good: Attach one black (negative) clamp to the negative terminal of the good battery. Black Clamp to Ground: Attach the final black clamp to an unpainted, metal part of the dead car's engine block or chassis. A bolt or bracket works perfectly. Start the Vehicles: Start the engine of the working car and let it run for a few minutes. Then, try to start the car with the dead battery. If it starts, let both cars run connected for a few more minutes. Disconnect in REVERSE Order: Once the dead car is running, carefully remove the cables in the exact reverse order: black clamp from the ground on the dead car, black clamp from the good battery, red clamp from the good battery, and finally, red clamp from the previously dead battery. Drive the jumped car for at least 20-30 minutes to allow the alternator to recharge the battery sufficiently. If the battery dies again soon after, it's likely old and needs replacement. Common Mistakes & Safety Data Incorrect cable connection sequence Leading cause of electrical system damage and sparks. Allowing clamps to touch during connection Creates a short circuit and can damage both vehicles. Using damaged or undersized cables Inefficient power transfer; can overheat and melt. Jump-starting a frozen or damaged battery Risk of explosion; inspect for cracks or leaks first. Average time needed to recharge via driving 30 minutes of highway driving is typically sufficient.
20
1
Share

how to put a bike on a car

The best way to carry a bike on your car depends on your vehicle type, budget, and how many bikes you need to transport. The three main options are hitch-mounted racks (the most stable and versatile), roof-mounted racks (ideal for sedans but watch for low clearances), and trunk-mounted racks (the most affordable but least stable). For most people, a hitch rack offers the best balance of security, ease of use, and vehicle compatibility. Before choosing, you must confirm your car's setup. Do you have a factory-installed hitch receiver ? Are there factory roof rails , or would you need to install a crossbar system ? Is your trunk lid made of plastic or composite materials that might not support a strap-on rack? These factors will narrow your choices significantly. Hitch-mounted racks are the gold standard. They attach to a square receiver tube at the rear of your vehicle. They keep the bikes completely clear of your car's body, offer excellent stability with minimal frame contact, and many models feature a tilting mechanism to allow access to the trunk without removing the bikes. They are, however, the most expensive option and require the initial cost of installing a hitch if your car doesn't have one. Roof-mounted racks use crossbars that span the width of your roof. Bikes are secured with fork-mount or frame-gripping cradles. This system keeps the rear of the car unobstructed and is great for keeping road grime off the bikes. The major drawbacks are fuel efficiency loss due to wind resistance and the constant risk of driving into a garage or low clearance with the bikes mounted. Trunk-mounted racks use a system of straps and hooks to attach to the edge of your trunk or hatchback. They are lightweight, affordable, and can be transferred between vehicles easily. However, they can potentially scratch your paint, obstruct your license plate and taillights if not installed carefully, and are generally less stable at highway speeds than the other two types. Feature Hitch-Mounted Rack Roof-Mounted Rack Trunk-Mounted Rack Average Cost $300 - $800 + hitch install $400 - $700 + crossbars $100 - $250 Stability Excellent Very Good Fair to Good Vehicle Impact Reduces departure angle Increases height, hurts MPG Risk of paint damage Ease of Loading Easy, waist-high Difficult, overhead Moderate Bike Security High, locked to hitch High, locked to roof Lower, straps can be cut Garage Clearance No issue Major concern No issue No matter which system you choose, always use a secondary retention strap (like a nylon strap around a wheel) as a backup and double-check that all bikes and rack components are secure before driving.
14
0
Share

how to price a classic car

Pricing a classic car requires a multi-faceted approach that goes beyond a simple online search. The core factors are the vehicle's condition (using a standardized grading system), its originality and authenticity, documented history , current market trends , and the results of comparable sales, often called "comps." There is no single price, but rather a value range determined by synthesizing these elements. For a precise valuation, consulting a professional appraiser is highly recommended. The most critical first step is to honestly assess the car's condition. The industry standard is a 1-6 point scale: Concours (1): Professionally restored, show-winning perfection. Excellent (2): Near-perfect, with minimal flaws. Good (3): A clean, presentable driver that may need minor work. Fair (4): Requires mechanical and/or cosmetic work to be reliable. Poor (5): A project car needing extensive restoration. Parts Car (6): Not roadworthy, valuable only for its components. A car's value is heavily tied to its originality . Numbers-matching—meaning the engine, transmission, and sometimes even the rear axle are the original units that left the factory—is a significant value booster. Documented ownership history, original bill of sale, maintenance records, and photos of a restoration process also add substantial credibility and value. You must then research the market. Monitor auction results from major houses like RM Sotheby's and Barrett-Jackson , and browse classifieds on Hemmings and Bring a Trailer . Look for sales of the same model, year, and similar condition. Remember, prices can be regional and fluctuate with economic trends. Finally, for insurance purposes or a high-value sale, a certified appraisal from a recognized organization like the Classic Car Appraisal Association of America provides an authoritative, defensible value. Valuation Factor Low-End Example (Fair Condition) High-End Example (Excellent, Numbers-Matching) Data Source / Note 1969 Chevrolet Camaro SS $35,000 $125,000+ Price varies massively with engine (396 vs 350), documentation, and restoration quality. 1957 Ford Thunderbird $40,000 $90,000+ Convertible vs. removable hardtop, and original color combinations affect value. 1970 Plymouth Hemi Cuda $150,000 (Project) $1,500,000+ (Restored) Engine option is the single biggest determinant of value for muscle cars. 1963 Chevrolet Corvette Sting Ray $50,000 $200,000+ Split-window coupe models command a significant premium over convertibles. 1965 Ford Mustang $15,000 $60,000+ V8 GT models and rare early "K-code" Hi-Po engines are far more valuable than standard six-cylinder models. Market Trend (Muscle Cars) +3.5% (2023) +12% (2021 Peak) Data from Hagerty Price Guide shows market cooling but still strong for top-tier examples. Appraisal Cost $150 (Basic) $500+ (Detailed) Cost depends on car's value and report detail required for insurance or legal purposes.
11
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.