What is the installation method for the Focus radiator lower guard?

1 Answers
VanEmily
07/30/25 7:03am
The installation method for the Focus radiator lower guard is: remove and set aside the bottom guard plate screws, then install the new guard plate and tighten the screws. The car radiator generally refers to the cooling radiator, which is part of the vehicle's cooling system. The radiator in the engine water cooling system consists of three parts: the inlet chamber, outlet chamber, main plate, and radiator core. The Focus is a compact car with dimensions of 4378mm in length, 1810mm in width, and 1468mm in height, a wheelbase of 2705mm, a fuel tank capacity of 53 liters, and a curb weight of 1242kg. The Focus features a MacPherson strut front suspension and a torsion beam rear suspension.
Was this review help?
14
2
Share
More Forum Discussions

How Long Does It Take for a Car Horn to Recover After Getting Wet?

Car horn recovery time after getting wet depends on the extent of water ingress. Below are two scenarios of car horn water ingress: Minor water ingress: In this case, no special treatment is usually needed. Simply allow the moisture inside the horn to evaporate naturally over 1 to 2 days. Once the water dries, the horn will return to normal. It's best to remove the horn and reinstall it after 1-2 days when completely dry. Severe water ingress: This situation requires disassembling the horn and using a hairdryer to blow-dry it. The heat from the hairdryer will accelerate the evaporation of internal moisture. The horn will function normally again after drying. If not addressed promptly, it may cause circuit short circuits and horn failure.
18
3
Share

Where is the VIN located on an electric vehicle?

Electric vehicles typically display the VIN in a rectangular slot below the handlebars, usually represented in a purely numerical format. Below is relevant information about VINs: VIN Introduction: The VIN, also known as the vehicle identification number, is a unique code assigned by the manufacturer to identify a specific vehicle. The VIN consists of a 17-character alphanumeric code, also referred to as the 17-digit identification code, chassis number, or 17-digit number. Functions of VIN: 1. Vehicle identification - In certain special circumstances, the VIN can accurately identify your vehicle, saving time due to its uniqueness. 2. Traffic violation queries - The VIN is required to check for traffic violations. As the vehicle's identification card, the VIN should be carefully safeguarded.
20
1
Share

How to Obtain a Heavy Truck Driver's License?

The driver's license for heavy trucks falls under the B2 category. You can directly apply for the B2 driver's license test without needing to obtain a small vehicle driver's license first. However, if you intend to drive a semi-trailer, you must first obtain a large vehicle driver's license before applying. To obtain the license, you need to pass three subject tests. Additional information: 1. Heavy and medium-duty trucks are issued large truck license plates (commonly known as yellow plates): Trucks with a length greater than or equal to 6 meters and a total mass greater than or equal to 12,000 kg are classified as heavy-duty trucks; trucks with a length greater than or equal to 6 meters and a total mass greater than or equal to 4,500 kg but less than 12,000 kg are classified as medium-duty trucks. 2. Light and mini trucks are issued small truck license plates (commonly known as blue plates): Trucks with a length less than 6 meters and a total mass less than 4,500 kg are classified as light-duty trucks; trucks with a length less than or equal to 3.5 meters and a load capacity less than or equal to 750 kg are classified as mini trucks. 3. Foreign-invested vehicle license plates (commonly known as black plates): All trucks owned by foreign-invested enterprises, regardless of type, are issued foreign-invested vehicle license plates (commonly known as black plates). The relevant departments of the Municipal Public Security Bureau Traffic Police Bureau require registered truck owners and drivers to conscientiously abide by traffic laws and regulations, drive in compliance with the rules, and ensure safe driving.
13
5
Share

How to reset the maintenance light on a BMW 530?

BMW 530 maintenance light reset method is: 1. Turn off the ignition switch and shut down the engine; 2. Press the dashboard reset button; 3. Turn on the ignition switch to power up and illuminate the dashboard; 4. Hold the reset button for 5 seconds until OILSERVICE appears, then release the reset button; 5. Press the reset button again for about 5 seconds until RESET starts flashing, indicating the reset is complete. The BMW 530 belongs to the mid-to-large-sized car category. Taking the BMW 530 2021 Sport Package as an example, its body structure is a 4-door, 5-seater sedan with body dimensions of: length 5106 mm, width 1868 mm, height 1500 mm, and a wheelbase of 3105 mm.
18
4
Share

What Does L Mean on a Car?

On a car, L stands for engine displacement. In some car models, L indicates a long-wheelbase version. Classification of car engine displacement: In China, car classifications are determined by engine displacement. Mini cars have a displacement of ≤1.0L; compact cars range from 1.0 to 1.6L; midsize cars range from 1.6 to 2.5L; executive cars range from 2.5 to 4.0L; and luxury cars have a displacement >4.0L. Long-wheelbase models: There are many long-wheelbase models on the market, such as the Audi A4L, Audi A6L, Audi A8L, Mercedes-Benz S450L, BMW 320Li, BMW 530Li, etc. Long-wheelbase models offer more spacious legroom and longer wheelbases.
17
3
Share

What is the method to reset the maintenance light on the Magotan?

Magotan maintenance light reset method is: 1. Turn off the vehicle key to make all instrument lights go out; 2. Press and hold the vehicle maintenance light reset button; 3. Turn on the vehicle key to make all instrument lights illuminate; 4. Continue holding the button for a moment to enter reset mode; 5. Release the maintenance reset button, then press button A within 20 seconds to complete the reset. Taking the 2020 Magotan as an example, its body dimensions are: length 4865mm, width 1832mm, height 1471mm, wheelbase 2871mm, fuel tank capacity 66l. The 2020 Magotan is equipped with a 1.4T turbocharged engine with maximum power of 110kW and maximum torque of 250Nm, matched with a 7-speed dual-clutch transmission.
12
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.