What is the installation method for the Audi A6L oil pump?

1 Answers
DeJade
07/29/25 8:50pm
Clean the oil pump of the Audi A6L 2.0T thoroughly. Apply a small amount of sealant to the gasket; then apply sealant to the mating surface of the oil pump. There is a hole on the balance shaft wheel. There is a hole on the upper diagonal of the oil pump housing that can accommodate a Phillips screwdriver. It should align with the point on the balance shaft wheel. Once aligned, the two flanges of the balance shaft should be level. Install the oil pump assembly smoothly onto the crankshaft; tighten all the surrounding mounting screws to complete the installation.
Was this review help?
1
0
Share
More Forum Discussions

Where are the three photos taken for running a red light located?

Three photos are used to determine running a red light. After the red light turns on, if the electronic eye captures three photos, it is defined as running a red light. The first photo is taken when the entire vehicle body crosses the stop line at the corresponding red light position. The second photo is formed when the entire vehicle crosses the stop line but still does not stop, and the vehicle enters the intersection or turns. The third photo is taken when the vehicle crosses the opposite side of the intersection. More relevant information is as follows: 1. The first photo shows the vehicle crossing the stop line, which is an instant violation image. From the moment the red light turns on, the electronic monitoring system starts shooting, as the electronic monitoring system and the red light are activated simultaneously with no time difference. 2. The second photo shows the vehicle crossing the center of the intersection, which is the second violation position. Many people believe that the electronic eye starts shooting three seconds after the red light turns on, so they proceed to cross the intersection and head towards the opposite side of the road. This is incorrect, as mentioned above, violation shooting occurs simultaneously with the red light turning on. 3. The third photo shows the vehicle crossing the opposite side of the intersection, which is the third violation position. This can also be considered an electronic panoramic image. Ultimately, determining whether a red light was run requires all three photos to be collected.
6
0
Share

Why is the spark plug too tight to remove?

The reason why the spark plug is too tight to remove is that it was over-tightened during installation. Therefore, when replacing the spark plug, the force applied should be based on the required torque for the specific spark plug being used. Spark plugs of different sizes require different amounts of force. Steps for replacing the spark plug: Open the hood, lift the plastic cover of the engine, and remove the high-voltage ignition wires. Mark the position of each cylinder to avoid confusion. Use a spark plug socket to remove the spark plugs one by one. When removing them, check for any external debris such as leaves or dust, and make sure to clean them thoroughly. Place the new spark plug into the spark plug hole, hand-tighten it a few turns, and then use the socket to tighten it further. Reinstall the removed high-voltage ignition wires according to the firing order, and then secure the cover. Spark plug replacement interval: Under normal maintenance conditions, spark plugs should be replaced every 40,000 to 60,000 kilometers. However, this may vary depending on the brand and engine type, so it is recommended to follow the user manual. The following standards can be used as a reference for maintenance and replacement: Platinum spark plugs should be replaced every 40,000 kilometers, ordinary nickel alloy spark plugs every 20,000 kilometers, and iridium spark plugs every 60,000 to 80,000 kilometers.
4
5
Share

What does the wrench light mean?

The wrench light coming on means it's reminding the owner that the vehicle needs maintenance. Here are some relevant introductions about car maintenance: 1. Introduction to car maintenance: Car maintenance refers to the preventive work of regularly inspecting, cleaning, supplying, lubricating, adjusting or replacing certain parts of the car, also known as car servicing. 2. The role of car maintenance: Modern car maintenance mainly includes: engine system (engine), transmission system, air conditioning system, cooling system, fuel system, power steering system, etc. The purpose of car maintenance is to keep the car clean and tidy, maintain normal technical conditions, eliminate hidden dangers, prevent failures, slow down the deterioration process, and extend the service life.
5
3
Share

What engine is used in the Haval H7?

The Haval H7 is equipped with the GW4C20B engine. An engine is a machine that can convert other forms of energy into mechanical energy. Taking the 2021 Haval H7 as an example, its body structure is a 5-door, 5-seat SUV with dimensions of 4715mm in length, 1925mm in width, and 1718mm in height, a wheelbase of 2850mm, a minimum ground clearance of 199mm, and a fuel tank capacity of 65 liters. The 2021 Haval H7 is powered by a 2.0T turbocharged engine with a maximum power of 167kW and a maximum torque of 385Nm, paired with a 7-speed dual-clutch transmission.
11
1
Share

How to Set the Horn Sound When Locking a Skoda?

Press and hold both the unlock and lock buttons on the remote key for 3 seconds until the light flashes, and the horn sound when locking will be successfully set. To set it to only flash the lights without the horn sound, press and hold both the unlock and lock buttons on the remote key for 3 seconds until the light flashes. Below are detailed instructions: 1. The horn sound when locking depends on the car model. Some models have a horn sound when locking, while others do not. 2. If the vehicle computer has a horn sound setting option, you can enable or disable it through this option. If the vehicle computer does not display this option, it can be activated via the bus system, which requires visiting a 4S shop or repair shop for setup. 3. Some models come with a horn sound feature, and the owner can manually set it. For certain models, the horn sound can be set using the car key by pressing both the unlock and lock buttons for 3 seconds until the light flashes, enabling the lights-only mode without the horn sound. 4. To restore the horn sound when locking, press and hold both the lock and unlock buttons for 3 seconds until the light flashes. 5. The horn sound when locking is produced by electromagnetic vibration. The electromagnetic coil attracts the relay's moving contact switch to close, allowing current to flow to the horn wiring. The current activates the electromagnet inside the horn, causing the diaphragm to vibrate and produce sound, hence the sound when locking the car.
1
5
Share

2021 New Regulations on Car Modifications: What Modifications Are Legal?

2021 new regulations on car modifications are as follows: 1. Wheel rim styles can be changed: The new regulations have relaxed the rules on wheel rim modifications. As long as the size and specifications of the wheel rims match those on the registration certificate, the style can be changed. It is even permissible for all four wheel rims to have different styles. 2. Roof racks and side step boards can be installed: This new regulation mainly applies to SUV and MPV models. The height of the installed roof rack must be within 300 millimeters, and the width of the side step board must not exceed 5 centimeters beyond the side of the vehicle body. 3. Vehicle body color can be changed: The vehicle body color can be altered through painting or wrapping, but the changes must be registered with the vehicle management office within ten days. It is important to note that colors similar to those used on police cars, fire trucks, and other official vehicles are not allowed. 4. Grilles and front/rear bumpers can also be modified: The styles of grilles and front/rear bumpers can be changed. However, the installation of new grilles and bumpers must not alter the original length and width of the vehicle. The vehicle emblem cannot be changed, and the bumpers must not have any obvious protrusions, such as the so-called 'tow hooks' which are not allowed. 5. Roof racks no higher than 30cm can be installed: The new regulations state that passenger cars can install roof racks no higher than 30cm, provided that safety and stability are ensured.
11
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.