What is the inspire car?

2 Answers
MacDakota
07/24/25 12:59pm
inspire is a model under Dongfeng Honda, and it is the Japanese version name of the Accord. The Dongfeng Honda inspire is the flagship sedan of Dongfeng Honda. The overall body dimensions of the Dongfeng Honda inspire are 4910mm in length, 1862mm in width, and 1450mm in height, with a wheelbase of 2830mm. The Dongfeng Honda inspire is equipped with a 1.5T turbocharged engine, with a maximum output power of 194 horsepower, a maximum power speed of 6000 rpm, a maximum torque of 260 Nm, and a maximum torque speed range of 1600 to 5500 rpm, paired with a CVT transmission. The hybrid model is equipped with a 2.0L engine and the iMMD hybrid system composed of dual motors.
Was this review help?
10
0
Share
MacJosephine
08/11/25 7:01am
I drove this car for a while before. The Honda Inspire is Honda's mid-size sedan, and the generation produced by Dongfeng Honda in China was actually a sibling model to the overseas Accord. It's positioned as more sporty than the Accord, with a particularly noticeable fastback design and a firmer chassis tuning. My hybrid version had a fuel consumption of only around 5L/100km, and the i-MMD system delivered very smooth acceleration. The interior space is truly spacious—you can cross your legs in the back seat, and the trunk can easily fit three suitcases. The infotainment system supports CarPlay, which is quite practical. As for downsides, the noise insulation is average, and tire noise is noticeable on gravel roads. After the 2019 model refresh, it's now basically discontinued, so if you want one, you’ll have to look for a used model.
Was this review help?
2
5
Share
Expand All
More Forum Discussions

What does China National V and VI mean for vehicles?

China National V and VI represent the emission standards for vehicle exhaust. Below is an introduction to National V and VI: 1. National V refers to the fifth stage of motor vehicle pollutant emission standards, with its emission control level equivalent to the Euro 5 emission standard currently implemented in Europe. 2. National VI refers to the sixth stage of motor vehicle pollutant emission standards. Below is additional information about National V and VI: 1. After a vehicle starts, the tailpipe emits harmful gases such as carbon monoxide, soot, and PM. Changing the vehicle's emission standards is aimed at effectively reducing the pollution of these wastes to the atmosphere. 2. The National VI standard is stricter than National V. 3. Registered National V emission vehicles must meet local emission standards and pass vehicle inspection before they can be driven.
16
3
Share

Why can't a motorcycle start after being left unused for a long time?

Motorcycle failure to start after prolonged storage can be attributed to the following reasons: 1. Gasoline that remains unused for over 6 months will develop gum deposits. Once gasoline forms gum deposits, it becomes unusable and must be discarded; 2. Extended storage causes loss of lubrication and sealing in various engine components, resulting in low cylinder pressure and insufficient lubrication of parts like the crankshaft. This makes the motorcycle difficult to start quickly, requiring manual rapid rotation of the crankshaft to restore oil flow and lubrication in the oil passages; 3. A battery left unused for 6 months will typically lose its charge, rendering it unable to start the motorcycle; 4. Electrical components such as spark plugs and ignition coils may become damp and develop electrical leakage.
13
3
Share

How to Install a Child Safety Seat Without ISOFIX Interface?

The following are specific methods for installing a child safety seat without an ISOFIX interface: 1. Use the seat belt to secure the seat. There are two installation methods: forward-facing and rear-facing, with rear-facing being more suitable for infants. 2. Since the seat belt can easily get stuck when stretched too long, pull it out completely at the beginning to facilitate subsequent steps and avoid insufficient length or getting stuck, which would require restarting the process. 3. Thread the seat belt through the seat, secure it with the seat's red fixing clip to prevent the belt from sliding and failing to hold the seat in place, then insert it into the buckle.
11
2
Share

How to Replace Car Air Conditioning Refrigerant?

Here are the steps to replace the refrigerant: 1. Discharge the refrigerant from the air conditioning system. 2. Remove the radiator; 3. Remove the condenser inlet and outlet pipes; 4. Unscrew the fixing bolts and remove the condenser; 5. Before installation, thoroughly clean the condenser to ensure sufficient airflow through the condenser coils for adequate heat dissipation; 6. During installation, pay attention to the correct position of the lower part of the condenser. The gap between the upper end and the engine hood should not be less than 5mm. Here is additional information on the symptoms of excessive refrigerant in car air conditioning: 1. The suction and discharge pressures of the air conditioning system are too high, and the equipment operates at elevated temperatures; 2. The current value of the compressor power supply is significantly higher, and prolonged operation may burn out electrical components; 3. The condenser is filled with refrigerant, reducing the heat exchange area, leading to high-pressure protection when the car air conditioning is turned on.
12
0
Share

How to Turn on the Air Conditioning Cooling in Audi Q5?

Here are the methods to turn on the air conditioning cooling in Audi Q5: 1. OFF air conditioning unit button, press the rotary regulator 2 to turn on or off the air conditioning unit. If another button or a rotary regulator is pressed, the air conditioning unit will also be turned on. When the air conditioning unit is turned off, the air supply from outside the vehicle is cut off. 2. A/C cooling operation mode, press the A/C button to turn on or off the cooling mode. When the cooling operation mode is turned off, the air is not cooled or dehumidified. In this case, water mist may form on the windshield. When the outside temperature is below zero, the cooling mode is automatically turned off. 3. Cooling operation, use the button to turn on/off the maximum cooling. When the cooling operation mode is turned off, the air is not cooled or dehumidified.
19
5
Share

What to Do When Your Car Battery Dies Because the Headlights Were Left On

Solutions for when your car battery dies due to leaving the headlights on are as follows: 1. Jump-start the car: If the battery dies in the city, the owner can ask a friend or a passing vehicle to jump-start the car using jumper cables. Connect the positive and negative terminals of the dead battery with the jumper cables, then attach the other ends to the rescue vehicle's battery. Start the dead car and drive to a repair shop as soon as possible for battery repair or replacement. 2. Call a tow truck: If this happens in a remote area, call a tow truck to take the car to a repair shop for charging. 3. Push-start the car (only for manual transmission cars): If the battery dies in the countryside with no passing vehicles to help, you can push-start the car. The specific method is to find a passerby to help push the car while the ignition is on. As the car starts moving, the driver should press the clutch and shift into second gear. When the speed increases slightly, release the clutch and gently press the accelerator to start the car.
5
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.