What is the Ideal RPM for Highway Driving?

Why does a car stall automatically after ignition?

Reasons why a car stalls automatically after ignition: 1. The vehicle's anti-theft system is triggered, locking the engine, allowing it to start but not run. Releasing the key causes the engine to stall while the anti-theft light turns on. This is mostly due to the owner privately duplicating a key without a chip to prevent key loss or because the key was dropped, weakening the signal and making it unrecognizable to the system; 2. The ignition module is damaged or the ignition reference signal line from the ignition module to the engine computer is faulty; 3. Ignition switch failure: The ignition line has power when starting, but releasing the key cuts off the power and stalls the engine. This is usually caused by poor contact of internal contacts in the ignition switch and is often accompanied by the dashboard battery light, oil light, or engine fault light not illuminating.

12

1

Share

How to Remove the Exterior Handle of an Older Audi A4?

First, use a flat-head screwdriver to pry open the lower trim panel of the door handle, starting from the middle and moving downward, then outward. After removing the lower trim panel of the handle, you will see two black 8mm hex bolts inside. Use a socket wrench to unscrew them. Disconnect the power window switch connector (there is a clip inside; you need to hook it from behind with your finger to remove it). Use a flat-head screwdriver to pry open the decorative panel of the door handle from front to back. Pull the door handle while removing it. Slightly pry open a gap at the bottom of the interior door panel, insert the wrench to pry, and apply force sequentially to remove the handle.

12

1

Share

How to Replace the Air Conditioning Filter in a CRV?

The method for replacing the air conditioning filter in a CRV: The filter is located inside the glove compartment in front of the front passenger seat. After removing the glove compartment, you can see the filter's cover plate. Remove the cover plate, pull out the old filter, and then insert the new filter in the same orientation. The Honda CRV is a compact SUV with dimensions of 4621mm in length, 1855mm in width, 1679mm in height, and a wheelbase of 2661mm. The CRV is equipped with two engines: a 1.5-liter turbocharged engine and a 2.0-liter naturally aspirated engine, both featuring aluminum alloy cylinder heads and blocks. The car's interior is refined, with a simple and practical dashboard wrapped in soft materials. It features the same digital instrument panel and color central control screen as the Civic. Higher-end models support Apple CarPlay and Android Auto functionality.

5

0

Share

At What Voltage Will a Car Battery Fail to Start the Engine?

When the car battery voltage drops below 12.2V and the load voltage is below 9.5V, the vehicle is likely to fail to start. Car owners should regularly inspect their car batteries during daily use. This can be done by checking the observation window on the battery. If the window displays black, it indicates the battery needs charging; green signifies good condition, while white suggests insufficient electrolyte. The battery is a crucial component of a car and also a wearable part that requires periodic replacement. As the number of charge and discharge cycles increases, the battery's performance may decline, hence the need for regular replacement.

17

1

Share

How to Add Refrigerant Oil to Car Air Conditioning?

There are three main methods for adding refrigerant oil to a car air conditioning compressor: direct addition, addition from the high-pressure side, and addition from the low-pressure side. The appropriate method should be chosen based on the actual situation. The specific procedures are as follows: 1. Direct Addition: If adding directly from the compressor, an oil return operation should be performed first. This involves running the compressor at idle speed with the control system set to the coldest and highest fan speed for 20-30 minutes to allow the oil to return to the compressor. Then, turn off the engine, release the refrigerant, remove the compressor from the vehicle, drain the old oil, and directly add or replenish new oil. 2. Addition from the High-Pressure Side: When adding from the high-pressure side, evacuate to 98 kPa, close the high-pressure side manual valve, and close the service valve on the compressor. Remove the high-pressure side hose from the gauge end and insert it into the refrigerant oil. Open the service valve to allow the refrigerant oil to be sucked into the system. Close the service valve immediately when the oil is nearly fully drawn to avoid sucking in air. Then, reattach the high-pressure hose to the gauge, open the high-pressure side manual valve, and continue evacuating before adding refrigerant. The engine and vacuum pump should not be running during this process. 3. Addition from the Low-Pressure Side: When adding from the low-pressure side, no service valve is needed. After evacuating to 98 kPa, close the low-pressure side manual valve while keeping the vacuum pump running. Keep the high-pressure side manual valve open, remove the low-pressure side hose from the gauge end, and insert it into the refrigerant oil to draw the oil. Once the oil is drawn, reattach the hose to its original position, open the low-pressure side manual valve, and continue evacuating before adding refrigerant. Note that too much refrigerant oil can impair cooling performance, while too little can damage the compressor. Always add the specified amount as per the vehicle's requirements.

4

2

Share

What does autohold in a car mean?

Autohold in a car is an automatic parking system that can adjust to the optimal driving state based on different road conditions. It effectively prevents frequent gear shifting on poor road surfaces and enables forced downshifting during overtaking. When the autohold button is pressed in D gear, the transmission will remain in second, third, or fourth gear. Autohold is a technical application that enables automatic handbrake functionality while driving. This technology allows drivers to avoid prolonged braking when the vehicle is stationary and prevents unnecessary coasting when the automatic electronic parking brake is engaged. It is particularly useful on slopes and during frequent starts and stops.

20

2

Share

What is the Ideal RPM for Highway Driving?

Why does a car stall automatically after ignition?

How to Remove the Exterior Handle of an Older Audi A4?

How to Replace the Air Conditioning Filter in a CRV?

At What Voltage Will a Car Battery Fail to Start the Engine?

How to Add Refrigerant Oil to Car Air Conditioning?

What does autohold in a car mean?

How to Use Car Air Recirculation and Fresh Air Mode

What to Do When the Gear Suddenly Becomes Loose and Cannot Be Engaged?

Where is the battery located in the BMW 3 Series?

What are the historical origins of Toyota?