What is the HUD function?

Will the rear seat passengers of a sedan be penalized for not wearing seat belts?

Penalties will be imposed. Drivers are not allowed to operate a motor vehicle when passengers fail to use seat belts as required. If passengers do not wear seat belts, traffic police will penalize the driver according to the law. The penalties for driving without wearing a seat belt are as follows: 1. Scenario one: When driving on urban expressways, if the driver fails to use a seat belt as required, a certain fine will be imposed and 2 points will be deducted; 2. Scenario two: When driving on roads other than highways or urban expressways, if the driver fails to use a seat belt as required, a certain fine will be imposed without point deduction.

5

2

Share

What to Do When Engine and Transmission System Problems Occur?

When the car engine is not working properly and the self-diagnosis system does not output any fault codes, it is especially necessary to rely on the operator's inspection and judgment to determine the nature of the fault and the location where the fault occurs. Relevant information about the engine is as follows: 1. Introduction: The car engine is the device that provides power for the car, acting as the heart of the car, determining its power, economy, stability, and environmental friendliness. 2. Classification: Depending on the power source, car engines can be divided into diesel engines, gasoline engines, electric vehicle motors, and hybrids, among others.

17

2

Share

What to Do When Gears Are Hard to Engage in a Hot Car?

Difficulty in shifting gears when the car is hot may be due to wear on the shift linkage, deterioration of the clutch pressure plate performance causing incomplete disengagement, severe wear of the synchronizer, or reduced performance of clutch fluid due to temperature effects. There may also be other reasons. It is recommended to check for issues like the deterioration of the pressure plate performance and reduced performance of clutch fluid due to temperature effects. Relevant information about automatic transmissions is as follows: 1. Introduction: An automatic transmission, as the name suggests, does not require the driver to manually shift gears. The vehicle automatically selects the appropriate gear based on driving speed and traffic conditions. Generally, automatic transmission cars have six gear positions, from top to bottom: P, R, N, D, S, L. 2. Principle of Automatic Transmission: The engine's power is transmitted through the transmission, which is also a key factor affecting fuel consumption. Generally, automatic transmissions consume 10% more fuel than manual transmissions. Whether manual or automatic, the more gears there are, the more fuel-efficient the transmission is.

19

3

Share

Why Does the Grand Cherokee Depreciate So Rapidly?

The significant depreciation of the Grand Cherokee may be attributed to its high fuel consumption and outdated technology due to its age. Below is an extended introduction about the Grand Cherokee: 1. Basic Introduction: The Jeep Grand Cherokee is a classic model launched by Chrysler. It inherits the pure lineage of the Jeep brand, featuring a classic exterior design, outstanding off-road capabilities, excellent on-road handling performance, and comprehensive safety features, pioneering the high-end off-road vehicle market. 2. Popular Period: In April 2007, the all-new Jeep Grand Cherokee, with significant improvements and upgrades in various aspects, was introduced in China. It garnered widespread acclaim for its exceptional off-road capabilities and outstanding on-road handling performance.

18

3

Share

What is the fuel tank capacity of the Buick Excelle 2013 model?

The fuel tank capacity of the Excelle 2013 XT 1.6L manual comfort version is 60L. The vehicle is equipped with a 1.6L naturally aspirated engine and a 5-speed manual transmission (MT). The drivetrain configuration is front-engine, front-wheel drive. The front suspension type is MacPherson independent suspension, while the rear suspension uses a compound torsion beam non-independent suspension. Among vehicles in the same class, the Nissan Sylphy 2022 Classic 1.6XE manual comfort version has a fuel tank capacity of 50L, and the Volkswagen Lavida 2022 1.5L manual fashion version has a fuel tank capacity of 51L. During actual refueling, the amount of fuel may exceed the calibrated capacity. This occurs because automakers measure fuel tank capacity from the tank bottom to a safe fill level, leaving additional space between this safe level and the tank opening. This design accommodates fuel expansion due to temperature increases, preventing overflow. If fuel is filled up to the tank opening during refueling, the actual fuel quantity will exceed the nominal tank capacity. To check remaining fuel levels, drivers can observe the fuel gauge on the right side of the instrument panel, marked with E (Empty) and F (Full). When the needle approaches E, it indicates low fuel, while proximity to F signifies sufficient fuel levels.

8

4

Share

What Causes the Engine Malfunction Light to Illuminate While the Vehicle Can Still Operate Normally?

The illumination of the engine malfunction light may serve as a warning, indicating that certain system parameters in the vehicle may have exceeded the set range. In such cases, the vehicle can usually continue to operate, and the light is typically yellow. There is also a more severe scenario where the light turns red, indicating a very serious malfunction. Although the vehicle might still be operable, for safety reasons, it must be stopped immediately, the engine turned off, and further driving prohibited until the fault is inspected. There are primarily seven reasons for the engine malfunction light to illuminate: Sensor Failure: This includes sensors such as coolant temperature, crankshaft position, air flow, intake temperature, and oxygen sensors. When these sensors are damaged, have poor contact, or signal interruptions, the vehicle's ECU cannot accurately obtain engine data, triggering the malfunction light. Fuel or Oil Quality Issues: Failure to use the fuel or oil as specified by the manufacturer may lead to engine wear, causing the malfunction light to illuminate. Poor Combustion of Air-Fuel Mixture: This can result in engine carbon buildup or knocking. Once detected by the oxygen sensor and reported to the ECU, the malfunction light will illuminate as a warning. Issues like spark plug failure, ignition coil failure, fuel pump failure, or clogged fuel lines can all lead to poor combustion. Turbocharger Issues: Problems with the intake boost system or turbocharger can also trigger the malfunction light. The most common issue is turbocharger damage, often accompanied by symptoms like oil leaks, excessive oil consumption, reduced power, metallic noises, or blue/black smoke from the exhaust. Intake System Problems: Blockages in the engine's intake system can lead to serious issues, causing the malfunction light to illuminate. A dirty air filter that hasn't been cleaned regularly can also cause intake problems. Exhaust System Issues: Exhaust faults can trigger the malfunction light. Common causes include faults in the rear oxygen sensor, catalytic converter, exhaust camshaft, or bearings, with the catalytic converter being the most frequent issue. Using leaded gasoline, lead or silicon-based lubricant additives, physical damage to the catalytic converter, or fuel system malfunctions can all contribute to catalytic converter failure. Anti-Theft System Malfunction: If the vehicle's electronic anti-theft system fails or if there is a mismatch between the anti-theft controller and the engine ECU, the anti-theft system can prevent the engine from operating normally, and the malfunction light will illuminate. If the engine malfunction light illuminates, follow these steps: First, check if the engine is running normally and look for signs like shaking or smoke. If present, avoid restarting the engine. Note: Never restart the engine if the light is red. If the engine can be started, turn it off and wait 5-10 minutes. Without pressing the brake, press the start button once or turn the key halfway to the 'on' position without depressing the clutch. The vehicle will perform a self-check upon powering up. Observe the dashboard after 5-10 seconds to see if the malfunction light turns off. If the light remains on, visit a service center as soon as possible. Technicians can use a portable diagnostic tool to read the fault codes, identify the issue, and perform targeted repairs.

15

1

Share

What is the HUD function?

Will the rear seat passengers of a sedan be penalized for not wearing seat belts?

What to Do When Engine and Transmission System Problems Occur?

What to Do When Gears Are Hard to Engage in a Hot Car?

Why Does the Grand Cherokee Depreciate So Rapidly?

What is the fuel tank capacity of the Buick Excelle 2013 model?

What Causes the Engine Malfunction Light to Illuminate While the Vehicle Can Still Operate Normally?

How to Dispose of Waste from RV Toilets?

How to Restore a Locked Steering Wheel?

What are the causes of low engine oil pressure?

What is the solution for sluggish electronic throttle response?