What is the horsepower of the McLaren 720s?

1 Answers
SanRylee
07/30/25 7:08am
The McLaren 720s has a horsepower of 720ps. The McLaren 720s is a 2-door, 2-seater hardtop sports car under the McLaren brand. Taking the 2019 McLaren 720s as an example, here are the specific details: 1. Dimensions: Its body dimensions are: length 4543mm, width 1930mm, height 1196mm, wheelbase 2670mm, trunk volume 360l, and curb weight 1283kg. 2. Powertrain: The 2019 McLaren 720s is equipped with a 4.0T twin-turbocharged engine, with a maximum power of 530kW and a maximum torque of 770Nm, paired with a 7-speed dual-clutch transmission.
Was this review help?
5
4
Share
More Forum Discussions

Why Does the Car Move Without Pressing the Accelerator?

There are two main reasons why a car moves without pressing the accelerator. Manual Transmission: During the idle phase of a manual transmission car, it will move at idle speed even when neither the accelerator nor the brake is pressed. This action is generally referred to as crawling start, and no matter at what speed the brake is released during the start, the vehicle will not stall. Automatic Transmission: Since automatic transmissions do not have a clutch, once the gear is shifted into drive, the car will move even without pressing the accelerator, typically at a speed of around 15 km/h. Therefore, to move at a very slow speed, the brake must be used to reduce the speed. Generally, the larger the engine displacement, the higher the idle speed will be, but it won't be excessively high because the first gear is, after all, a low-speed gear.
4
4
Share

Within how many seconds should a hill start be completed?

A hill start should be completed within 30 seconds. Hill starts require attention to technique. Control the speed properly: When performing a hill start, the speed should be slightly faster before ascending the slope to give the car a bit of momentum; otherwise, it may lack power to climb. Once the rear wheels are on the slope, immediately reduce the speed to allow the car to move slowly. If the speed is too fast, it may be difficult to adjust the car's position relative to the side line in time. Choose the right reference point: To maintain an appropriate distance between the car body and the right side line during a hill start, it is essential to know the position of the right front wheel. Since the driver cannot see the right front wheel from inside the car, a reference point on the car must be used instead.
12
4
Share

Is the Tachometer a Reliable Reference for Hill Starts?

Is the tachometer a reliable reference for hill starts? Using the tachometer as a reference is a practical method for performing hill starts in a car. Overview: Hill starts are part of the on-site driving test in the second subject of the driver's license examination, which involves starting a vehicle parked on a steep slope and moving it upward. Hill starts are one of the test items in the driver's license examination and are included in the on-site driving test of the second subject. Requirements: After the vehicle comes to a stop, if the front bumper of the car or the front axle of the motorcycle is not aligned with the pole line and exceeds 50 centimeters in either direction, it is considered a pass. If the front bumper of the car or the front axle of the motorcycle is not aligned with the pole line but does not exceed 50 centimeters in either direction, 10 points will be deducted.
3
4
Share

What is the diameter of the MG6 OEM brake disc?

The diameter of the MG6 OEM brake disc is 355x32mm. Methods to obtain brake disc dimensions: Brake disc dimensions do not need to be queried. If you want to replace your brake disc, simply remove it and measure the diameter. Brake discs generally require replacement only after a very long mileage, and they should be inspected regularly during maintenance. During use, brake discs may develop some grooves. If there are many deep grooves, the brake disc needs to be replaced. When replacing brake discs, it is important to note that the front and rear brake discs have different sizes, with the front brake discs usually being larger than the rear ones. Location of brake discs: They are located in the center of the tire. Disc-type brake discs can be seen through the gaps in the wheel rim, while drum-type ones require the wheel hub to be removed.
15
2
Share

What is the time limit for hill start?

Hill start time limit is 30 seconds. Hill start is one of the items in the driver's license test. Overview: The motor vehicle driver's license test is an official driving skills examination conducted within the territory of the People's Republic of China to obtain legal permission to drive motor vehicles. Upon passing the test, the applicant will receive a corresponding class license. Others: The Ministry of Public Security of China published the revised "Regulations on the Application and Use of Motor Vehicle Driver's Licenses" on its official website. According to these regulations, the content and passing standards of the driver's license test will be unified nationwide. On May 10, 2021, the Ministry of Public Security held a press conference to announce 12 convenience measures, including deepening the reform of "simplifying administration, delegating power, improving regulation, and upgrading services" in public security traffic management.
19
3
Share

Should You Alternate Between High and Low Beams When Overtaking During the Day?

You can alternate between high and low beams when overtaking during the day. It is important to use vehicle lights correctly while driving. Headlights: The primary purpose of headlights is to illuminate the road and objects ahead to ensure driving safety. Alternating between high and low beams can be used as a signal for overtaking at night. Headlights are installed on both sides of the front of the vehicle, with each car equipped with 2 or 4 headlights. The bulb power is 45-60W for high beams and 25-55W for low beams. Fog Lights: Fog lights are installed near the headlights or slightly lower. In low visibility conditions such as fog, snow, heavy rain, or dust, fog lights provide road illumination and serve as a signal for oncoming vehicles. The light is mostly yellow, as yellow light has a longer wavelength and better fog penetration. The bulb power is typically 35W.
19
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.