What is the height of the Odyssey?

Where is the car jack located in the trunk?

Car jacks are generally placed underneath the spare tire in the trunk, with designated mounting positions. These are located along the protruding long edges on both sides of the vehicle's underbody, where there are several reinforced areas specifically designed for jack placement. Here's additional information: 1. Passenger cars: For family vehicles, the support points are typically on the inner side of the side skirts, approximately 20 cm behind the front wheels and 20 cm in front of the rear wheels, capable of withstanding relatively high pressure. Incorrect operation, such as placing the jack on chassis steel plates, bumpers, or crossbeams, may cause the side skirts to deform, resulting in unnecessary damage to the chassis. 2. Precautions: When using a jack, ensure the car is parked on a safe and level surface with the brakes engaged. Additionally, pay attention to the jack's maximum load capacity and never exceed it to prevent accidents due to insufficient support.

13

2

Share

What Causes a Motorcycle Carburetor to Leak Fuel?

Debris may lift the float needle and prevent it from returning to its position, causing fuel from the tank to continuously flow into the carburetor without self-closing. Since the carburetor's fuel bowl has a limited capacity, any excess fuel will leak out. Below are the relevant details: 1. Carburetor: The carburetor is one of the main components of a motorcycle, and its primary function is to supply gasoline to the engine. Due to its critical role, the carburetor is often referred to as the "heart" of the engine, highlighting its significant importance in motorcycle operation. 2. Specific Cause: The carburetor's float needle is typically made of conical corrosion-resistant rubber. Although it is corrosion-resistant, prolonged use or frequent use of low-quality gasoline can cause wear. As a result, when the worn float needle closes the fuel inlet, tiny gaps may form, allowing fuel to slowly seep into the carburetor. This raises the fuel level, eventually causing it to overflow through the drain tube.

11

1

Share

What is the TRIP button?

"Trip mileage (Trip)" and the "Total mileage (Odometer)" on the left are different. The trip mileage helps users calculate the distance of each trip and can be reset by long-pressing the clear button. The total mileage records the vehicle's overall travel distance. Here is an introduction to TRIP: 1. TRIP: A mileage selection button that can record three types of mileage. One is the regular odometer, which cannot be reset and records the vehicle's total mileage. 2. Operation 1: Press the TRIP button once to display the second mileage meter. Hold this button to reset this meter, allowing you to record the distance from point A to point B. 3. Operation 2: Press the TRIP button again to display the third meter, with the same operation as above. Press the TRIP button once more to return to the first odometer, meaning there are two meters to record the distance between A and B.

8

2

Share

What are the functions of the engine lubrication system?

The functions of the engine lubrication system are as follows: 1. Reduce friction resistance: The lubricating oil forms an oil film between moving parts to reduce friction resistance and power loss, and minimize wear of components. 2. Prevent excessive part temperature: The cooling effect utilizes the fluidity of the oil to carry away some of the heat from engine parts, preventing them from overheating and burning out. 3. Cleaning effect: The circulating oil carries away metal particles worn off during engine operation, dust inhaled from the atmosphere, and some solid substances produced by fuel combustion, preventing the formation of abrasives between parts that could increase wear. 4. Sealing effect: The viscosity of the oil allows it to adhere to the surfaces of moving parts, improving the sealing effect and reducing air leakage. 5. Anti-rust effect: The lubricating oil film adheres to metal surfaces, isolating air and water, thereby providing anti-rust and anti-corrosion protection.

12

2

Share

Motorcycle Gear Shifting Issues?

When riding a motorcycle, you may encounter difficulties in gear shifting. Below is a detailed explanation of the reasons behind motorcycle gear shifting problems: 1. Operational reasons: When starting the vehicle, if the throttle is too large and the clutch is released too quickly, the gear shifting can feel stiff. 2. Motorcycle manufacturing process: If the manufacturing precision of vehicle components is insufficient, the clutch may not fully disengage, leading to abnormal noises during gear shifting, accompanied by a jerking forward motion. This type of fault is difficult to address unless the entire clutch is replaced. 3. Clutch malfunction: As the vehicle ages, the clutch naturally develops issues with incomplete disengagement, but this problem can be resolved through maintenance. 4. Sprocket issues: In cases of severe wear on the motorcycle's connecting components, especially the front sprocket, slipping of the sprocket may occur. If the chain is loose or the gap between gear levers increases, such noises may also appear.

14

5

Share

Does a 2012 car need inspection this year if it was inspected last year?

A 2012 car that underwent inspection last year does not require inspection this year, but should undergo regular inspection next year. Current regulations stipulate that new cars are inspected once every six years, then every two years from the seventh to tenth year. From ten to fifteen years, annual inspections are required. Vehicle inspections help promptly eliminate safety hazards, encourage proper maintenance, and reduce traffic accidents. Below are the contents of motor vehicle inspections: 1. Document verification: Check for the vehicle manual, certificate of conformity (import vehicles require commodity inspection certificates), and ensure factory inspection marks on the vehicle body are complete. 2. Measurement of vehicle dimensions: Measure internal and external contour dimensions, track width, and wheelbase. Specific measurements include vehicle length, width, height, cargo compartment height and area, track width, and wheelbase. 3. Completion of modification registration form: Conduct inspections according to technical standards. Upon passing, fill out the "Initial Inspection and Modification Registration Form for Motor Vehicles" and specify the curb weight, load capacity, passenger capacity, and driver's compartment seating as per manufacturer specifications.

14

1

Share

What is the height of the Odyssey?

Where is the car jack located in the trunk?

What Causes a Motorcycle Carburetor to Leak Fuel?

What is the TRIP button?

What are the functions of the engine lubrication system?

Motorcycle Gear Shifting Issues?

Does a 2012 car need inspection this year if it was inspected last year?

Which Volkswagen model features a black emblem?

What are the symptoms of a faulty motorcycle brake pump?

What are the tips for using the Audi A4L auto start-stop function?

What are the symptoms of a faulty motorcycle water temperature sensor?