What is the headlight model of the Lavida?

2 Answers
OColton
07/29/25 7:40pm
The headlight model of the Lavida is H7. Lavida headlights: The SAIC Volkswagen Lavida comes standard with ordinary halogen dual-beam headlights, and the headlight bulb model is H7. Usually, the bulb cannot be replaced without removing other car parts first. Headlight installation: For self-installation, first remove the switch. The switch is easy to remove—press it down, twist it to the right, and then pull it up. Next, remove the fuse box cover panel. Extend the original car's plug connected to the switch from the side and connect it to one end of the module wiring harness. Then, apply a bit of 3M tape to the back of the main unit. Insert the white plug from the wiring harness and the light-sensitive wiring harness into the main unit. After that, insert the unit into the dashboard from the side and stick the main unit in the appropriate position.
Was this review help?
13
4
Share
DiHolden
08/14/25 3:00pm
When I first bought the Lavida, I was also curious about the headlight model. Later, I figured out that most of them use H7 halogen bulbs, especially the older models before 2015. Changing the bulb is quite convenient—just remove the lamp cover and rotate the buckle. No need to go through the hassle of checking the model; simply open the hood and look at the label or flip through the manual—that’s the simple method I often use to confirm. When replacing the bulb, wear gloves to avoid oil stains on the filament, which can cause it to break easily. Here’s a tip: if the light dims, don’t delay—check immediately, as it might be burnt out or the wiring might have aged, affecting nighttime visibility. Replacing it promptly can greatly improve driving safety, especially in rainy or foggy conditions. DIY saves money; you can find H7 bulbs on Taobao for just a few dozen yuan. But be aware that there might be slight variations across different years—for example, some newer models come with integrated LED lights, which are best handled by a professional shop for safety.
Was this review help?
4
2
Share
Expand All
More Forum Discussions

What are the differences between Volvo T3, T4, and T5?

T3 is a 1.5T three-cylinder engine, while T4 and T5 are both 2.0T inline 4-cylinder engines. The T3 1.5T three-cylinder engine has a maximum power output of 120KW and a maximum torque of 265N·m. The T4 2.0T inline 4-cylinder engine delivers a maximum power of 140KW and a maximum torque of 300N·m. The T5, also a 2.0T inline 4-cylinder engine, boasts a maximum power of 185KW and a maximum torque of 350N·m. Below are the relevant details about these three engines: 1. Different engines: The distinction between these engine types lies in their power output. The T3 is a 1.5T three-cylinder engine, whereas the T4 and T5 are both 2.0T inline 4-cylinder engines. 2. Different power outputs: The T3 has a maximum power of 120KW and a maximum torque of 265N·m. The T4 offers a maximum power of 140KW and a maximum torque of 300N·m. The T5 provides a maximum power of 185KW and a maximum torque of 350N·m.
1
1
Share

How Long Does Painting Take?

The time required for car painting is primarily determined by the scope of the painting. Generally, at a 4S shop, the fastest turnaround is 2-3 days. Below are the precautions for painting and methods for car paint maintenance: Precautions for Painting: After painting, check if the painted surface matches the original car paint color perfectly. Inspect the smoothness of the painted surface for any bubbles, pits, or impurities. Examine the uniformity of metallic paint particles, observing their size, color, and arrangement to ensure consistency and harmony with the original car paint. Methods for Car Paint Maintenance: To enhance the lifespan and appearance of the car paint, wash the car regularly to remove stains and dust. Avoid strong impacts, bumps, or scratches to the car's paint film. If any scratches, dents, or peeling are found on the painted surface, repair them promptly.
3
2
Share

What Causes No Response When Pressing the Accelerator?

The reasons for no response when pressing the accelerator include ignition system failure, fuel injection system failure, and throttle pedal sensor failure. Below are detailed explanations: Ignition System Failure: Failure of the ignition coil and spark plugs in the ignition system leads to poor ignition performance, making it difficult to achieve noticeable power improvement even when pressing the accelerator. Fuel Injection System Failure: Failure of the high-pressure fuel pump or excessive carbon buildup in the fuel injectors results in poor fuel injection performance, causing no response when pressing the accelerator. Throttle Pedal Sensor Failure: Throttle pedal sensor failure is the most direct cause and requires replacement of a new sensor.
9
1
Share

What is the service life of commercial vehicles?

Commercial vehicles have different service life periods depending on the vehicle type. Please see the detailed explanations below: 1. Non-commercial passenger vehicles with 9 seats or less (including sedans and SUVs) have a service life of 15 years: If continued use is required after reaching the scrapping standard, no approval is needed. The service life can be extended after passing inspections, with 2 annual inspections required. After 20 years, 4 annual inspections are required starting from the 21st year. 2. Tourist passenger vehicles and non-commercial passenger vehicles with more than 9 seats have a service life of 10 years: If continued use is required after reaching the scrapping standard, the current procedures must be followed, but the extension cannot exceed 10 years. Tourist passenger vehicles with extended service life require 4 annual inspections, while non-commercial passenger vehicles with more than 9 seats require 2 annual inspections, increasing to 4 annual inspections starting from the 16th year after exceeding 15 years. 3. The service life of commercial buses is adjusted to 10 years: If continued use is required after reaching the scrapping standard, the current procedures must be followed. The extension cannot exceed 4 years, with 4 annual inspections required during the extended period. 4. For the above vehicles during regular inspections: If they fail to meet the national standard "Safety Specifications for Power-driven Vehicles Operating on Roads (GB7258-2004)" in 3 consecutive inspections within one inspection cycle, the license plate and vehicle registration certificate will be revoked, and the vehicle owner will be notified to complete the deregistration process. After reaching the scrapping standard, registration and transfer registration are not allowed. 5. Important note: Commercial vehicles converted to non-commercial use and non-commercial vehicles converted to commercial use will be scrapped according to the commercial vehicle standard (8 years).
9
1
Share

What Causes Water to Drip from the Car Chassis?

The reasons for water dripping from the car chassis are drainage from the air conditioning system and water dripping from the muffler and exhaust pipe at the rear of the car. Here are the detailed explanations: Air Conditioning System Drainage: Air conditioning system drainage occurs because the outside temperature is high in summer while the interior of the car with the air conditioning on is cold, creating a temperature difference that causes water to drip from the chassis. The low-pressure pipes of the car's air conditioning system are not wrapped with thermal insulation foam, making the pipe surfaces prone to condensing moisture from the air. Water droplets also condense and collect at the lowest point of the pipes, dripping down. Muffler and Exhaust Pipe Dripping: Water dripping from the muffler and exhaust pipe at the rear of the car is also a normal phenomenon, commonly seen in winter. This phenomenon indicates that the engine is in good working condition, with the air-fuel mixture burning completely and efficiently.
20
3
Share

Can a Car Battery with Broken Cells Still Be Used?

After a battery has broken cells, it cannot be used and should be repaired immediately. The causes and repair methods for broken battery cells are as follows: Causes of Broken Battery Cells: The reasons for broken battery cells include poor battery quality; incorrect usage leading to internal short circuits; frequent battery use; or severe impacts or drops. Repair Methods for Broken Battery Cells: For a battery with broken cells, the problematic single cell can be extracted and replaced. After replacement, seal it with sealing glue, weld the terminals, add electrolyte, and finally charge the battery. Those with the necessary skills can attempt to repair it themselves, but it is best to seek professional help at a repair shop.
7
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.