What is the ground clearance of the XPeng P7?

1 Answers
DelParker
07/29/25 6:50pm
The unladen ground clearance of the XPeng P7 is only 130mm (even lower when loaded with passengers), which is lower than the typical ground clearance of sedans when unladen, as sedans generally exceed 150mm. Definition of minimum ground clearance: Chassis height (i.e., minimum ground clearance) is defined as the distance between the lowest protruding part of the vehicle's chassis and the level ground when the vehicle is fully loaded. Impact of chassis height: Minimum ground clearance reflects a vehicle's ability to pass over obstacles or uneven terrain without collision. Generally, for family sedans, the minimum ground clearance ranges between 110mm and 150mm. A lower chassis height (typically below 11cm) enhances high-speed stability but reduces off-road capability.
Was this review help?
16
0
Share
More Forum Discussions

How Often Should the Automatic Transmission Fluid Be Changed for a Corolla?

For a Corolla, the automatic transmission fluid should be changed every 40,000 kilometers, while the manual transmission fluid should be changed every 60,000 kilometers. Below are the methods for changing the transmission fluid for a Toyota Corolla: 1. Gravity Drain: The principle is similar to changing engine oil. After loosening the tightening nut at the bottom of the oil pan, the transmission fluid will automatically drain out through the drain hole. 2. Machine Flush: New transmission fluid is added to the flushing machine, which is then connected to the transmission fluid circuit. The machine's function is to push out the old fluid with the new one, ensuring a cleaner flush of the fluid circuit. 3. Oil Pan Removal Method.
6
4
Share

What is the difference between the internal and external air circulation modes in a car's air conditioning system?

Internal air circulation means that the air only circulates inside the car, driven by the blower to cycle the cabin air. External air circulation, on the other hand, connects the interior of the car with the outside. While driving, airflow automatically enters the cabin due to wind pressure, and when stationary, outside air can still enter the blower through the air ducts and be blown into the cabin. Below is an introduction on when to use each mode: 1. External air circulation: For a newly purchased car, it is essential to keep the external air circulation mode on as much as possible to maintain airflow between the inside and outside of the car. This helps to quickly release harmful gases from the cabin. Additionally, during long highway drives, keeping the internal air circulation mode on for too long can lead to insufficient oxygen levels in the cabin, causing driver fatigue and potentially leading to accidents. In such cases, switching to external air circulation can replenish fresh air inside the car. 2. Internal air circulation: During regular driving, we mostly use the internal air circulation mode. However, it is crucial to switch to internal air circulation during heavy traffic, as the density of exhaust fumes in the air increases with congestion. This mode effectively prevents outside exhaust from entering the cabin, protecting occupants from harm. It is also advisable to use internal air circulation during sandstorms or dusty weather, as it not only prevents dust from entering the cabin but also reduces the impact of sand on the air conditioning filter.
8
3
Share

Where is the engine oil filler port located?

The engine oil filler port is generally located on the left side of the engine. 1. Slowly unscrew the oil filler cap in the reverse direction, open the cap, and pour in the oil. When reinstalling the oil filler cap, use the oil on the dipstick to lubricate the cap opening, then smoothly tighten it in the correct direction until it is properly seated. 2. Regarding the position for adding engine oil, the oil should be filled up to the upper limit mark on the dipstick for optimal performance. Overfilling can create excessive resistance for the engine, which may increase fuel consumption. Below are the basic steps for adding engine oil: (1) After the car has been turned off and parked for about ten minutes, pull out the dipstick and wipe the oil marks clean with a cloth. (2) Reinsert the dipstick into the dipstick tube, then pull it out again to check the oil marks. Normally, the oil marks should be between the upper and lower marks on the dipstick, slightly above the middle line. (3) If the oil marks are below the lower mark, it indicates insufficient oil, and you should add oil immediately. While adding oil, continuously pull out the dipstick to monitor the oil level. (4) When topping up the oil, try to use the same type of oil as the one already in the engine to avoid mixing different brands or grades of oil.
18
0
Share

How to Turn Off Auto Start-Stop in a Car?

The steps to turn off the auto start-stop feature in a car are as follows: 1. Press and hold the brake pedal while the vehicle is in normal operation. 2. The auto start-stop system will activate, and the indicator light on the dashboard will illuminate. 3. Press the "off" button for the auto start-stop system. 4. The dashboard will display that the system has been turned off, indicating the auto start-stop is deactivated. Here is an introduction to the auto start-stop feature: The engine auto start-stop system automatically shuts off the engine when the vehicle comes to a temporary stop (such as at a red light) and restarts it automatically when it's time to move forward again.
2
2
Share

How to Use the Heating System in the 10th Generation Accord

Before using the heating system in the 10th Generation Accord, you need to wait until the engine coolant temperature rises to a certain level. The heating control knob has red and blue color markers on both sides. Generally, the cold air setting is on the left, and the warm air setting is on the right. Turning the knob to the left decreases the car's temperature, while turning it to the right increases the temperature. After the engine coolant temperature has risen, you can turn on the air conditioning by adjusting the fan speed control. Below is an introduction to using the heating system in the Accord: 1. During winter use, after starting the engine, the coolant temperature is still relatively low. In this state, you should not use the heating system because the air blown by the AC will be cold. Turning on the AC immediately will not raise the interior temperature but will instead increase the engine's load. 2. When starting the car cold, you need to drive for a while until the engine coolant temperature rises and stabilizes at around 90 degrees Celsius. At this point, you can turn on the car's heating system. Set the air circulation to external circulation first to expel the cold air from the cabin, then switch to internal circulation. The interior temperature will rise quickly.
20
4
Share

What are the reasons for an automatic transmission not engaging?

The main reasons why an automatic transmission car cannot engage gears are the following two aspects: 1. A malfunction has occurred inside the gear lever assembly. 2. The P-gear locking solenoid inside the gear lever has failed, and the brake switch has malfunctioned. Here are the measures that can be taken if an automatic transmission car cannot engage gears: (1) Replace the vehicle's clutch cable. (2) Go to a professional auto repair shop and have professionals adjust the clutch cable and gear lock inside the vehicle, as these two areas being too tight can directly affect the difficulty of gear engagement, and in more severe cases, can even prevent the vehicle from engaging gears. (3) Replace the clutch master cylinder inside the vehicle to resolve the issue of not being able to engage gears.
17
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.