What is the ground clearance of the Volkswagen Lamando?

3 Answers
OBrianna
07/29/25 4:23pm
The ground clearance of the Volkswagen Lamando is 114 millimeters. Ground clearance refers to the distance between the lowest point of the car (excluding the wheels) and the supporting surface when the vehicle is fully loaded and stationary. It is used to indicate the car's ability to pass over obstacles such as rocks and tree stumps without collision. The Volkswagen Lamando is a compact car. Taking the 2021 Volkswagen Lamando as an example, its body dimensions are: length 4615 mm, width 1826 mm, height 1425 mm, with a wheelbase of 2656 mm and a fuel tank capacity of 51 liters. The 2021 Volkswagen Lamando is equipped with a 1.4T turbocharged engine, with a maximum power of 96 kW and a maximum torque of 225 Nm, paired with a 7-speed dual-clutch transmission.
Was this review help?
3
3
Share
NoraMarie
08/14/25 5:14am
The ground clearance of the Volkswagen Lamando is typically around 130mm. Having driven this car for several years, I find this height quite suitable for urban roads. For instance, when going over speed bumps or small potholes in the city, the car rarely scrapes the bottom. However, extra caution is needed on rough and uneven roads as the chassis might get scratched, so I usually slow down when passing such areas. It can handle waterlogged roads during rainy days, but if the water depth exceeds 15 centimeters, it's better to take a detour. After all, sedans aren't designed for off-road use, and a higher ground clearance could negatively impact stability and fuel consumption. For regular maintenance, it's advisable to frequently check the chassis for any damage from stone impacts. In summary, this car offers agile handling, but road conditions should always be taken into consideration.
Was this review help?
2
5
Share
Expand All
JourneyFitz
10/12/25 7:26am
I've tested the Lamando on various road conditions with a ground clearance of around 130mm. It offers a comfortable ride but requires extra caution on rough roads. For example, when entering rural dirt roads, the chassis is prone to scraping against gravel, forcing me to slow to minimum speed. Compared to SUVs with over 200mm clearance, the Lamando is noticeably lower, but this gives it better cornering stability and fuel efficiency. For daily use, you can add underbody protection panels to minimize damage. Also, remember the clearance decreases when fully loaded, so be mindful when loading luggage. Regular cleaning of accumulated mud under the chassis is recommended to prevent corrosion.
Was this review help?
1
5
Share
Expand All
More Forum Discussions

What are the reasons why the BYD G3 one-button start cannot detect the key?

BYD G3 one-button start cannot detect the key for the following reasons: 1. Dead key battery: The first thing to consider is whether the key is out of power. If the remote control distance shortens or the sensing becomes less sensitive, these are signs that the key battery is running low. In a dead battery state, the one-button start function cannot work properly, and the battery needs to be replaced. 2. Interference: Check if there is any electromagnetic interference nearby, such as signal interference sources. Some dash cams that lack proper electromagnetic shielding can also cause interference, preventing the key from being detected. 3. Gear position: Verify if there was an operational error, such as the gear not being placed in the P position.
7
0
Share

What is a Car Wheel Composed Of?

Wheels are typically composed of two main components: the rim and the spokes. The rim is the part of the wheel where the tire is mounted and supported, while the spokes are the supporting components between the axle and the rim. In addition to these parts, wheels sometimes also include the hub. The rim is the component that surrounds and supports the tire on the wheel, forming the wheel together with the spokes. The rim and spokes can be integral, permanently connected, or detachable. The spokes are devices that protect the wheel rim and spokes of the vehicle, characterized by a pair of circular cover plates whose diameter is close to that of the wheel rim. Based on the structure of the spokes, wheels are divided into disc-type and spoke-type. Currently, mainstream family cars mostly use disc-type spoke structures. The hub is the cylindrical metal component inside the tire that supports the tire, mounted centrally on the axle. It is also known as the wheel rim, steel rim, or tire ring. Tire Usage Tips: Inspect the tires. If the damaged area is on the sidewall of the tire or the tread groove depth is worn (depth less than 2 millimeters), and the damage is severe enough to be irreparable, a new tire is needed. Do not arbitrarily change the tire size; choose tires that match your car. Since the seal between the tire and the hub is very tight, professional equipment is required to separate the tire from the hub. The tire should be rotated evenly to avoid damaging the hub during removal. Completely remove the tire from the hub. Once the tire is off, check the hub for any impact damage. Installing a tire on a damaged hub not only results in poor sealing and air leakage but can also lead to dangerous fractures.
17
1
Share

What is the normal tire pressure for a Haval H6 in winter?

The normal tire pressure for a Haval H6 in winter is between 2.3BAR and 2.7BAR. The Haval H6 is a compact SUV. Taking the 2021 1.5T manual urban edition as an example, the exterior dimensions of the vehicle are 4600mm in length, 1860mm in width, and 1720mm in height, with a wheelbase of 2680mm. The 2021 1.5T manual urban edition is equipped with a 1.5L inline 4-cylinder turbocharged engine, delivering a maximum horsepower of 150hp, a maximum power of 110kW, a maximum power speed of 5600rpm, a maximum torque of 210Nm, and a maximum torque speed range of 1800 to 4400rpm.
3
4
Share

Why is the steering wheel of a small car so heavy?

Reasons for a heavy steering wheel in small cars: 1. Lack or deterioration of power steering fluid; 2. Severe wear or insufficient lubrication in the steering system; 3. Malfunction of steering system components; 4. Incorrect front wheel toe-in parameter; 5. Low tire pressure. Solutions for a heavy steering wheel in small cars: 1. Perform timely maintenance; 2. Add or replace power steering fluid. Maintenance methods for small car steering wheels: 1. Avoid turning the steering wheel to its limit when making turns; 2. Install a leather steering wheel cover; 3. Reduce excessive force when turning the steering wheel; 4. Develop good steering wheel usage habits. Working principle of small car steering wheels: Converts circular motion into linear motion through a rack and pinion mechanism, thereby pushing the wheels to rotate.
12
2
Share

Where is the fuel filler switch located on the Beidou Star?

The fuel filler cap switch of the Beidou Star is located under the driver's seat. Simply pull the switch to open the fuel filler cap. The Beidou Star's instrument panel design is straightforward, not particularly fashionable but not outdated either. The speedometer, tachometer, and fuel gauge are neatly arranged, making them clear and easy to read. The 4-spoke steering wheel offers good tactile feedback, and there is no interference with observing the instrument indicators while driving. Here are some additional details: Interior features: The layout of various function buttons inside the car is also very reasonable, with no inconvenience felt. Due to the Beidou Star's tall body, it provides ample seating space, but the trade-off is an increased drag coefficient, which affects the vehicle's power and fuel economy. However, the Beidou Star's K10A engine does not seem to be significantly affected by this.
6
1
Share

What is the function of a hammer drill clutch?

The function of a hammer drill clutch is to protect the user's safety. When encountering rebar during drilling, it prevents reverse rotation that could cause injury. The clutch serves as a safety protection mechanism. More details about the hammer drill clutch are as follows: 1. Introduction: A hammer drill is a commonly used power tool. With the development of the power tool industry, the requirements for its functions have become increasingly higher. 2. Principle: The principle of a hammer drill involves the transmission mechanism driving the drill bit to perform a rotational motion while also generating a reciprocating hammering motion perpendicular to the rotation. The hammer drill operates by the transmission mechanism driving a piston to reciprocate and compress air within a cylinder. The periodic changes in air pressure inside the cylinder drive a hammer inside the cylinder to reciprocate and strike the top of the drill bit, hence the name 'hammer drill'.
15
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.