What is the ground clearance of the MG5?

1 Answers
BradyMarie
07/29/25 6:26pm
The ground clearance of the MG5-2021 model is 145 millimeters. The ground clearance of the MG5-2021 refers to the distance between the lowest point (excluding the wheels) and the supporting plane, which indicates the vehicle's ability to pass over obstacles such as rocks and tree stumps without collision. A higher ground clearance for the MG5-2021 improves its off-road capability, but if the ground clearance is too high, the stability at high speeds may decrease. A brief introduction to the car: The MG5 is a trendy coupe designed for young people who pursue dynamic and stylish driving, blending fashion, quality, and sportiness. The dimensions of the MG5-2021 are 4675 mm in length, 1842 mm in width, and 1473 mm in height, with a wheelbase of 2680 mm. Generally, the ground clearance of sedans ranges between 110 mm and 150 mm, while SUVs have a ground clearance between 200 mm and 250 mm. However, the ground clearance of the MG5-2021 is not static; it also depends on the load condition. Therefore, changes in ground clearance should be considered based on the load variations of the MG5-2021. When selecting a vehicle, ground clearance can be one of the reference factors. The choice should depend on the vehicle's intended use and the road conditions. For urban driving with well-paved roads, a lower ground clearance can enhance stability and comfort. For long-distance travel or driving in areas with poor road conditions, a higher ground clearance may be preferred to avoid scraping or damaging the chassis.
Was this review help?
17
5
Share
More Forum Discussions

What Causes Clutch Abnormal Noise?

Abnormal noise when depressing the clutch pedal mainly occurs during engagement or disengagement. The most common cause is insufficient lubrication of the clutch pedal return spring. Below is relevant information about clutches: 1. Introduction: The clutch is located inside the flywheel housing between the engine and transmission. The clutch assembly is secured to the rear plane of the flywheel with screws, and the output shaft of the clutch serves as the input shaft of the transmission. 2. Function: During vehicle operation, the driver can depress or release the clutch pedal as needed to temporarily disconnect or gradually engage the engine with the transmission, thereby interrupting or transmitting power from the engine to the transmission. The clutch is a common component in mechanical transmission systems, allowing the drivetrain to be engaged or disengaged at any time. 3. Basic requirements for clutches: Smooth engagement; quick and thorough disengagement; easy adjustment and repair; compact size; lightweight; good wear resistance and sufficient heat dissipation capacity.
15
0
Share

Can a temporary ID be used for driving practice and logging hours?

Temporary ID can be used for driving practice and logging hours. Below are relevant details about the driving test: 1. Subject 1: Road traffic safety laws, regulations and related knowledge written test, computer-based, 100-point scale with 90 or above required to pass (including 90). 2. Subject 2: Field driving skills test, practical vehicle operation on closed course, pass/fail only. Includes five mandatory sequential tests: reverse parking, parallel parking, S-curve, right-angle turn, and hill start/stop. 100-point scale with 80 or above to pass (including 80). 3. Subject 3: Road driving skills test, practical vehicle operation on public roads or simulated course. 100-point scale with passing scores: 90+ for large buses, 80+ for large trucks, 70+ for other vehicle types. 4. Subject 4: Safe and civilized driving knowledge written test, 100-point scale with 90 or above required to pass (including 90).
14
4
Share

What to Do When Your Foot Goes Numb from Pressing the Clutch While Practicing Driving?

When your foot goes numb from pressing the clutch while practicing driving, you need to adjust your sitting posture. Here are some relevant introductions about the clutch: 1. Introduction: The clutch is located inside the flywheel housing between the engine and the gearbox. The clutch assembly is fixed to the rear plane of the flywheel with screws, and the output shaft of the clutch is the input shaft of the gearbox. 2. Function: During driving, the driver can press or release the clutch pedal as needed to temporarily separate or gradually engage the engine and the gearbox, thereby cutting off or transmitting the power from the engine to the gearbox. The clutch is a common component in mechanical transmission, allowing the transmission system to be separated or engaged at any time. 3. Basic requirements for the clutch: Smooth engagement, quick and thorough separation; easy adjustment and repair; compact size; lightweight; good wear resistance and sufficient heat dissipation capacity.
15
0
Share

How to Make Left and Right Turns on an Overpass in Subject 4?

When driving a motor vehicle through an overpass and encountering a turn, reduce speed and turn on the right turn signal 100 to 50 meters before the exit. Below is relevant information about Subject 4: 1. Concept: Subject 4, also known as the Subject 4 theory test or driver theory test, is part of the motor vehicle driver's license assessment. 2. Retake Instructions: If Subject 4 is not passed, there is no need to retake the previously passed subjects (Subject 1, Subject 2, Subject 3). You can schedule a retake on your own, and no retake fee is required. The safe and civilized driving theory test has no scheduling restrictions. However, the driving skills test permit is valid for three years. If the applicant does not complete the test within the validity period, the results of any passed subjects will be invalidated.
2
4
Share

Can Compulsory Traffic Insurance Cover My Own Vehicle Repairs?

Compulsory traffic insurance cannot cover repairs for your own vehicle. If you only have compulsory traffic insurance, there will be no compensation in the event of an accident. Compulsory traffic insurance is designed to compensate for property damage or personal injury caused to the other party in a two-vehicle accident. Only if you have purchased vehicle damage insurance can you receive compensation for your own vehicle's damage in a single-vehicle accident. Additional Information: Introduction: The full name of compulsory traffic insurance is 'Compulsory Motor Vehicle Traffic Accident Liability Insurance.' It is a mandatory liability insurance where the insurance company compensates for personal injury or property damage caused to victims (excluding passengers in the insured vehicle and the insured person) in road traffic accidents involving the insured vehicle, within the liability limits. Compulsory Traffic Insurance Premium Standards: Compulsory traffic insurance is China's first mandatory insurance system implemented by national law. Its premiums follow a nationally unified standard set by the state, but the price of compulsory traffic insurance varies for different vehicle models, with the main influencing factor being 'the number of vehicle seats.'
5
1
Share

Why is a large vehicle emitting black smoke?

Excessive black smoke from diesel engine exhaust is mostly caused by incomplete combustion due to uneven or excessive fuel supply to each cylinder, insufficient air intake, poor atomization, or premature injection timing. Here are methods to identify the cause of black smoke emission: 1. Observe the exhaust smoke color: Remove the air filter and observe the exhaust smoke color. If the black smoke condition improves, the issue is caused by severe contamination of the air filter. 2. Check the fuel supply timing: Verify if the fuel supply timing is too early. If it is, adjustments should be made. 3. Check cylinder fuel supply: During engine operation, conduct a fuel cut-off test for each cylinder. When a cylinder's fuel supply is cut off, if the engine speed decreases, black smoke significantly reduces, and knocking sounds weaken or disappear, it indicates excessive fuel supply to that cylinder. If the engine speed changes slightly and black smoke disappears, it suggests poor spray quality from that cylinder's injector. After identifying the faulty cylinder, inspect the injector. If necessary, replace it with a new injector for comparison. If the issue disappears with the new injector, it confirms the original injector is faulty.
4
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.