What is the ground clearance of the Honda Haoying in centimeters?

2 Answers
LaJames
09/05/25 6:44am
Honda Haoying's ground clearance is 193mm when fully loaded and 208mm when unloaded. Detailed information is as follows: 1. The role of ground clearance: The larger the minimum ground clearance, the stronger the vehicle's ability to pass over obstacles or uneven terrain, but the higher the center of gravity, which reduces stability; the smaller the minimum ground clearance, the weaker the vehicle's ability to pass over obstacles or uneven terrain, but the lower the center of gravity, which can increase stability. 2. The principle of minimum ground clearance: The minimum ground clearance must consider the passability of loading and unloading platforms during transportation, as well as the possibility of not scraping when the car is close to the edge of a sidewalk. If sales are limited to a specific country or region, local road quality must also be considered. Additionally, the value of the minimum ground clearance has certain limitations, as it is related to the vehicle's function and aerodynamics.
Was this review help?
10
5
Share
ValerieLee
09/17/25 7:02am
As someone who drives frequently, I've researched the ground clearance of the Honda Haoying. The standard design is approximately 18 cm, but there may be slight fluctuations depending on whether the vehicle is unloaded or fully loaded. The height measurement point is usually at the center of the vehicle or the lowest component, such as under the transmission, which ensures minimal scraping during city driving. At 18 cm, it ranks in the upper-middle range among mainstream SUVs, performing well over speed bumps and slippery roads, but don't expect much off-road capability. Factors affecting clearance include tire size or pressure and suspension condition. Switching to larger tires might increase it slightly, but it's recommended to maintain the factory settings. For daily driving, this height reduces the risk of scraping the undercarriage, especially on bumpy roads, but it also results in a higher center of gravity, making turns slightly slower. Therefore, it's important to regularly check tire wear and maintain the suspension.
Was this review help?
11
4
Share
Expand All
More Forum Discussions

What Causes Engine Surging?

The causes of engine surging are as follows: 1. High engine idle speed. 2. Improper adjustment of the throttle cable or throttle position sensor, resulting in excessively high main oil circuit pressure. 3. Delayed upshift. 4. Cracked or loose vacuum hose of the vacuum-type throttle valve. 5. Malfunction of the main oil circuit pressure regulator valve, causing excessively high main oil circuit pressure. 6. Stuck damper piston, failing to provide damping effect. 7. Missing one-way valve steel ball, causing shift actuators (clutch or brake) to engage too quickly. 8. Slipping shift actuators. 9. Oil pressure solenoid valve not functioning. 10. Faulty ECU.
14
3
Share

How many liters of engine oil does the Mercedes-Benz GLA200 require?

The Mercedes-Benz GLA200 requires approximately 6.5 liters of engine oil. The engine should use fully synthetic oil that meets the European oil certification standard A3B4 and the Mercedes-Benz oil certification standard 229.3/229.5. The oil viscosity grade can be either 5W-30 or 0W-40. For lower fuel consumption, 5W-30 is recommended, while 0W-40 provides better protection at high temperatures and high RPM. Currently, engine oils on the market can be broadly categorized into mineral oils and synthetic oils based on their base oils (vegetable oils are not considered due to their scarcity). Synthetic oils are further divided into full synthetic and semi-synthetic oils. Synthetic oils have a wider operating temperature range, longer service life, and higher costs. For the same oil film requirements, synthetic oils can achieve the desired performance with lower viscosity, whereas mineral oils require higher viscosity to meet the same standards. When adding engine oil, do not pour it all into the engine at once. It is best to add it gradually while measuring the level. Pull out the Mercedes-Benz's built-in oil dipstick (located near the engine), wipe off the attached oil with a cloth, reinsert it, and then pull it out again to check the dipstick's scale marks. The oil level should be between the upper and lower limit marks, not exceeding the upper limit. This is the standard oil level. If too much oil is added and exceeds the upper limit, the rising temperature during driving can cause the oil seals to burst, leading to oil leaks. Adding too little oil can affect engine lubrication and cooling.
7
0
Share

How long does it take to fully charge the BAIC EU5 with fast charging?

BAIC EU5 battery fast charging time is directly related to battery temperature. Specific fast charging time: When the battery temperature is below 0°C, the battery cannot be fast charged. When the battery temperature is between 0-15°C, it takes about 70 minutes to fast charge the battery SOC from 30% to 80%; when the battery temperature is between 15°C-40°C, it takes about 40 minutes to fast charge the battery SOC from 30% to 80%; when the battery temperature is between 40°C-45°C, it takes about 70 minutes to fast charge the battery SOC from 30% to 80%. Normally, the battery temperature is higher than the ambient temperature. When the ambient temperature is below 15°C, it is recommended to fast charge the vehicle immediately after operation. Precautions during charging: Please choose a relatively safe environment for charging, such as avoiding environments with liquids, fire sources, etc.; do not modify or disassemble the charging equipment and related ports without authorization, as this may cause charging failures and lead to fires; before charging, please ensure that there is no water or foreign objects in the charging ports of the vehicle, power supply equipment, and charging connection device, and that the metal terminals are not damaged or affected by rust or corrosion. Charging is not allowed under these circumstances. Abnormal terminal connections may cause short circuits or electric shocks, threatening life safety.
19
3
Share

What Causes a BYD Car Alarm to Keep Sounding?

BYD car alarm keeps sounding due to controller failure, doors not being properly closed, or a short circuit in the wiring. Below are the specific causes and solutions: Controller Failure: It could be a fault in the alarm itself or a malfunction in the triggering sensor. The trigger sensitivity might be set too high, leading to irregular alarms that disrupt rest. Short Circuit in Wiring: If the door edge switch, hood switch, or trunk switch is closed, it indicates the door is not properly shut. A grounded trigger wire means a short circuit in the wiring, causing the alarm to sound continuously until the battery is drained. In such cases, you can adjust the sensitivity of the alarm on the anti-theft control box. Typically, the anti-theft control box is installed under the dashboard. After removing the cover, you will find a screw knob that can be turned to adjust the sensitivity. Solutions: It is recommended to reduce the sensitivity to a level where kicking the tire does not trigger the alarm. For daily parking, using the silent mode of the anti-theft system is advised. Even without sound, the anti-theft system can still protect the car. It will automatically cut off power and sound an alarm if it detects an abnormal start of the vehicle, switching to audible mode. If the anti-theft system detects continuous vibrations and keeps sounding, it will disturb others and drain the car's battery.
7
4
Share

What Causes Engine Block Cracking?

Engine block cracking can be caused by: 1. Only adding water to the radiator without antifreeze: When external temperatures drop too low, the water inside the engine block freezes and expands, causing the block to crack. 2. Adding excessive cold water directly to an overheated engine or splashing cold water on it: This causes thermal shock to the engine block, leading to cracks that may propagate under severe impacts. Relevant information about automotive engines includes: 1. Introduction: The automotive engine is the power-generating device of a vehicle, serving as its heart that determines performance, fuel efficiency, stability, and environmental friendliness. Common gasoline and diesel engines are both types of reciprocating piston internal combustion engines. 2. Classification: Based on power sources, automotive engines can be categorized into diesel engines, gasoline engines, electric vehicle motors, and hybrid systems among others.
6
0
Share

What causes the BMW X3 to shake at idle?

BMW X3 idle shaking causes are as follows: Severe carbon buildup: The most common cause of car shaking is a dirty throttle body or excessive carbon deposits in the fuel injectors. When there's too much carbon buildup inside the engine, the gasoline sprayed by the cold start injector gets largely absorbed by the carbon deposits, resulting in an overly lean air-fuel mixture during cold starts. This makes starting difficult - the engine only starts easily after the carbon deposits become saturated with gasoline. After starting, the gasoline adsorbed on the carbon deposits gets sucked into the combustion chamber by the engine's vacuum, making the mixture too rich. This alternating between lean and rich air-fuel mixtures causes idle shaking after cold starts. The lower the temperature, the more fuel required for cold starts, and the more carbon deposits affect cold start performance. Ignition system issues: Check the condition of spark plugs, high-voltage wires, and ignition coils. Poor ignition system performance or bad spark plug firing can also cause such symptoms. Unstable fuel pressure: If you've already cleaned engine carbon deposits, cleaned the throttle body, replaced gaskets and spark plugs, but still experience body shaking at idle, we recommend checking fuel supply pressure and intake pressure sensors at a 4S shop. Abnormal fuel pump pressure or faulty intake pressure sensor readings can both cause body shaking. Aging engine components: Car shaking can also be related to worn engine mounts. Engine mounts act as the engine's vibration damping system, absorbing minor vibrations during operation. If engine mounts fail, these vibrations get transmitted to the steering wheel and cabin, causing shaking at idle.
12
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.