What is the ground clearance of the Haval F7x?

1 Answers
OGrace
07/30/25 2:23am
Haval F7x's ground clearance is approximately 159mm, which is sufficient for general road conditions. The Haval F7x is a compact car equipped with two engine options: a 1.5-liter turbocharged engine and a 2.0-liter turbocharged engine. The 1.5-liter turbocharged engine delivers a maximum power of 124 horsepower and a peak torque of 285 Nm, while the 2.0-liter turbocharged engine produces a maximum power of 224 horsepower and a peak torque of 385 Nm. Both engines are paired with a 7-speed dual-clutch transmission.
Was this review help?
15
4
Share
More Forum Discussions

What Are the Methods for Defrosting Cars in Winter?

There are several methods for defrosting cars in winter, including the warm air defrosting method, physical defrosting method, chemical defrosting method, and maintaining consistent temperatures inside and outside the car. Here are the details: 1. Warm Air Defrosting: The best method is to start the car and, once the engine coolant temperature rises, use the warm air to blow on the windshield until the ice melts. 2. Chemical Defrosting: In many markets and auto parts stores, there are stalls selling specialized anti-fog products, such as defrosting sprays or fog-resistant towels. Spray these defrosting agents onto the inner surface of the car glass and wipe them clean. While removing dirt from the glass, they also form a thin, transparent protective film that prevents moisture from condensing on the glass and forming a fog layer. One application can prevent fogging for about ten days to half a month. 3. Maintaining Consistent Temperatures Inside and Outside the Car: The reason the front windshield of a car is prone to icing in winter is due to the high temperature inside the car and the low temperature outside. To avoid this issue, it's simple: after parking, don't lock the car and leave immediately. Instead, open the doors to ventilate until the temperature inside the car is similar to the outside temperature before locking and leaving. This way, the windshield won't ice up the next morning.
19
0
Share

What Causes the Squealing Noise from Brake Discs That Then Disappears?

This is due to worn brake pads. When this occurs, new brake pads should be replaced. Brake pads are consumable parts in the braking system that require periodic replacement. As the vehicle's mileage increases, the brake pads will continuously wear down and need replacement once they reach a certain level of wear. Below is an introduction to related content: Introduction: The braking system is a crucial system in a vehicle, directly related to driving stability and safety. Main Components: The main components of the braking system include the vacuum booster pump, master cylinder, slave cylinder, brake pads, and brake discs. The vacuum booster pump provides assistance, making it easier for the driver to press the brake pedal. When the brake pedal is pressed, the master cylinder pushes the slave cylinder via brake fluid. At this point, the slave cylinder can press the brake pads against the brake disc, slowing the vehicle down. The brake disc is also a wear item that requires periodic replacement. As the vehicle's mileage increases, the brake disc will continuously wear down and need replacement once it reaches a certain level of wear. Precautions: The brake fluid in the braking system also needs regular replacement. Brake fluid is a liquid that easily absorbs moisture. If the brake fluid's water content becomes too high, it can lead to reduced braking force and longer braking distances. Therefore, it is essential to regularly replace the brake fluid during vehicle use. When the brake fluid's water content reaches 3%, it should be replaced immediately.
12
2
Share

What does it mean to replace an engine assembly?

Replacing an engine assembly means removing and replacing the entire engine. Engine assembly includes: Fuel supply and regulation system: Its main function is to provide the required fuel for mixture formation and combustion in the engine cylinders. Crankshaft and connecting rod mechanism: Its purpose is to convert the reciprocating motion of the pistons into the rotational motion of the crankshaft, changing the way force is applied, allowing the rotational power to be transmitted to the gearbox for proper distribution. Valve train and intake/exhaust systems: Based on the engine's combustion conditions, the valve train can appropriately adjust the amount of mixture supplied to the engine, maximizing combustion efficiency. The intake/exhaust systems automatically open and close valves for intake or exhaust. Lubrication and cooling systems: The lubrication system also lubricates internal components while the engine is running, while simultaneously transferring heat and dissipating some of the engine's heat. Pros and cons of replacing an engine assembly: The advantage of replacing an engine assembly is that it can provide superior power performance, and you can also make minor program adjustments according to your preferences to enhance the overall driving experience. The engine is a very complex instrument, and installation and matching must be done without any errors; otherwise, there will be certain safety hazards, potentially causing "secondary damage" to the entire vehicle. A slight mistake could lead to severe consequences, even fatal accidents.
11
5
Share

What is the principle of a car's transmission?

The principle of a vehicle's transmission is to use gear combinations with different numbers of teeth to achieve changes in speed and torque. It adjusts the transmission ratio and traction requirements under various driving conditions, allowing the engine to operate under favorable conditions; it facilitates vehicle development and driving; enables quick engine start-up and operation, vehicle gear shifting or parking, and transmits power to the drive wheels; when the clutch is engaged after shifting to neutral, the transmission stops power input. Functions of a manual transmission: 1. Change the transmission ratio to expand the range of torque and speed variations of the drive wheels; 2. Under the premise of maintaining the same rotation direction when starting the car, use the reverse gear to complete vehicle development and driving. The transmission is a very important component in a vehicle. It can change the transmission ratio and expand the torque and speed effects of the drive wheels. With the development of modern technology, transmissions have been upgraded from the original manual transmissions to continuously variable transmissions, and from non-synchronized to synchronized, making operation increasingly convenient. Currently, diesel engines are widely used in construction machinery, but their torque and speed variation ranges are small and cannot meet the requirements for traction and driving speed under various working conditions. Therefore, transmissions are used to resolve this contradiction. The quality of transmission performance is a key factor in measuring the power, economy, and drivability of construction machinery.
2
5
Share

How to Start a Motorcycle When the Battery is Dead?

When a motorcycle's battery is dead, you can start it using the kick starter, or by putting it in third gear with the clutch engaged, pushing the bike to its maximum speed, then releasing the clutch to start the engine. Alternatively, you can recharge the battery before starting. Below are specific reasons why a motorcycle may fail to start: 1. Dead Battery: A dead battery is a common issue during daily riding, requiring timely checks to ensure the battery is functioning properly. This is especially prevalent in colder winter temperatures, and aging motorcycle batteries are more prone to failure. 2. Fuel Valve: These valves contain a filter screen that may become clogged over time. If the fuel valve is the cause of the motorcycle not starting, gently tapping it externally or cleaning the interior can often resolve the issue.
9
2
Share

What is the thermal efficiency of the Blue Whale engine?

The thermal efficiency of the Blue Whale engine is 40%. Here are the specific details about the Blue Whale engine: Technical aspects: The Blue Whale Power platform also masters and applies various core cutting-edge technologies. For example, the Schaeffler intelligent cam phasing system, which is the world's first mass-produced system of its kind, is used in the NE engine. Compared to conventional products without this system, it achieves lower oil consumption while improving the adjustment response speed by 175%, enabling the engine to build torque more quickly during acceleration. Official data shows that it can achieve a 0-100 km/h acceleration in 7.9 seconds and a fuel consumption of 5.9 liters per 100 kilometers. The Blue Whale NE engine has increased thermal efficiency to a record-breaking 40%.
4
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.