What is the ground clearance of the Geely Xingyue L?

What Causes Steering Wheel Vibration in a New Car?

New car steering wheel vibration can be caused by the following reasons: Friction between plastic components: Since steering wheels are typically made of plastic parts, they may harden in cold temperatures, potentially causing friction noises. Abnormal sounds from the steering wheel: If the abnormal sound originates from inside the steering wheel, the issue is most likely caused by the steering wheel's clock spring (airbag coil). Aging of tie rod ends: Worn tie rod ends can cause steering wheel vibration and noise. This situation usually requires replacing the tie rod ends followed by a wheel alignment.

15

1

Share

What does pressure loss on the left rear side mean?

A pressure loss warning for the left rear tire indicates abnormal tire pressure in that tire, which requires calibration. Tire pressure standards: According to the international GBT2978-2008 standard requirements: Standard tires: 2.4-2.5bar; Reinforced tires: 2.8-2.9bar; Maximum pressure: should not exceed 3.5bar. Introduction to tire pressure: Tire pressure, strictly speaking, refers to the air pressure inside the tire. In automotive maintenance, the engine is the heart of the car, and its damage will lead to the end of the car's life. Similarly, tire pressure is the blood pressure of the car, and the level of tire pressure plays a crucial role in the performance and power of the vehicle.

12

1

Share

Should the front wheels press on the yellow line during hill-start parking?

The standard is to align the front of the car with the center line. Pressing on the line is not allowed. The front bumper being positioned on the second yellow line is considered passing. Introduction to hill-start parking: Hill-start parking is an assessment point in the driver's license subject two test. It evaluates the driver's ability to operate the vehicle on an uphill slope, correctly park the vehicle at a fixed location near the edge, accurately use the gear, accelerator, and clutch, and then start smoothly. If the vehicle's bumper is not aligned with the pole line during the parking, exceeding 50cm forward or backward, the test will be failed. Precautions: Before ascending the slope, adjust the direction to the correct position in the shortest time possible.

5

Share

What is the function of an overhead crane buffer?

The function of an overhead crane buffer is to control direction, lifting, forward and backward, left and right movements, as well as limit positioning. Other functions of buffers: In the field of computers, a buffer refers to a buffer register, which is divided into input buffers and output buffers. In other fields, there are elevator buffers, automotive spring buffers, etc., whose purpose is to reduce speed and improve safety and comfort. Principle of buffers: In CPU design, the DC load capacity of a general output line can drive one TTL load. In connections, a single CPU address line or data line may be connected to multiple memory chips, but memory chips are MOS circuits, mainly capacitive loads, with DC loads much smaller than TTL loads. Therefore, in small systems, the CPU can be directly connected to the memory, while in large systems, buffers need to be added.

20

5

Share

How to Solve Xenon Headlight Scattering?

It is recommended to replace with new lamp housings or try installing focusing lenses. The main causes of xenon headlight scattering are as follows: 1. Installation techniques or bulb physical parameters may cause the headlight optical center to shift. Since the modified light source center deviates from the originally designed optical center position, scattering inevitably occurs. Similarly, when the optical center shifts left or right, improper focusing will also occur. 2. Changes in light wavelength cause lens parameters to mismatch with the light source wavelength. The second reason for scattering in modified HID xenon headlights is the significant difference between the main spectrum of HID and the original halogen lights, leading to poor focusing. However, within the visible light range, the refractive index changes little with light waves, so the main cause of chromatic dispersion in modified HID xenon headlights is the displacement of the light source position.

2

Share

What Does Engine Timing Include?

Automobile engine timing three-piece set refers to the timing belt, tensioner pulley, and idler pulley. Introduction to the timing kit: The timing kit is a complete component package for automobile engine maintenance, including the tensioner, tensioner pulley, idler pulley, and timing belt required for the timing transmission system, as well as hardware components such as bolts, nuts, and gaskets that should be replaced regularly to ensure the timing transmission system and engine are in optimal condition after maintenance. Timing belt precautions: The timing belt is a consumable part. Once the timing belt breaks, the camshaft will not operate according to the timing, which can easily cause the valves and pistons to collide, resulting in severe damage. Therefore, the timing belt must be replaced according to the mileage or time specified by the manufacturer.

18

5

Share

What is the ground clearance of the Geely Xingyue L?

What Causes Steering Wheel Vibration in a New Car?

What does pressure loss on the left rear side mean?

Should the front wheels press on the yellow line during hill-start parking?

What is the function of an overhead crane buffer?

How to Solve Xenon Headlight Scattering?

What Does Engine Timing Include?

Does Full Car Polishing Have a Significant Impact on Car Paint?

Does adding windshield washer fluid to coolant have any impact?

What Causes Fluctuations in Average Fuel Consumption?

How Often Should Engine Belts Be Replaced?