What is the ground clearance of the Baojun 510?

1 Answers
OscarMarie
07/30/25 6:55am
Baojun 510 has a ground clearance of 200mm. 1. Structure: The front suspension of the Baojun 510 adopts the common MacPherson strut design. Whether in terms of structure, layout, or materials used, the front suspension of the Baojun 510 does not differ significantly from vehicles in the same price range. The front subframe also follows the traditional "wishbone" design. Although "C"-shaped and "box"-shaped subframes offer superior structural advantages, they also come with relatively higher costs. 2. Design details: The Baojun 510 features a deflector plate below the front wheel arches, primarily aimed at reducing tire turbulence to lower noise levels. The underside of the chassis is covered with two large plastic panels, which mainly serve to minimize turbulence under the chassis, contributing to noise reduction and improving vehicle stability. Additionally, these panels provide a certain degree of protection for the chassis.
Was this review help?
13
4
Share
More Forum Discussions

What are the differences between Tiggo 7 and Tiggo 7 PLUS?

Tiggo 7 and Tiggo 7 PLUS mainly differ in terms of exterior, interior, and powertrain. The differences are as follows: Exterior differences: The rear section of the Tiggo 7 PLUS features the same integrated LED taillights as the Tiggo 7. Additionally, the Tiggo 7 PLUS adopts a double-layered spoiler design on the roof, which is stylish, youthful, and more vibrant and dynamic. The new model's exclusive centrally positioned brake light at the top of the taillight, set against the layered spoiler, creates a unique highlight when illuminated. Configuration differences: The Tiggo 7 PLUS is equipped with the Kunpeng powertrain system, which includes a 1.6TGDI engine and a 7-speed wet dual-clutch transmission. It delivers a maximum output power of 145 kW and a peak torque of 290 Nm, with an NEDC fuel consumption of only 6.9 liters per 100 kilometers. In comparison, the 1.5T engine in the Tiggo 7 is slightly less impressive.
12
5
Share

What is the matching channel number for Audi's electronic water pump?

Audi's electronic water pump does not require a matching channel number. The specific reasons are as follows: The electronic water pump uses piezoelectric materials as the power device, achieving complete electronic control from control to drive. It fully controls liquid transmission through an electronic integrated system, thereby realizing the adjustability and precision of liquid transmission. It is a new type of water pump that can serve as a water circulation system to cool the vehicle's water supply system. The working principle of Audi's electronic water pump is as follows: The motor's circular motion drives the diaphragm inside the pump to perform reciprocating motion through a mechanical device, thereby compressing and stretching the air in the pump chamber (fixed volume). Under the action of a one-way valve, positive pressure is formed at the water outlet (the actual output pressure depends on the assistance received at the pump's outlet and the pump's characteristics). A vacuum is created at the water inlet, generating a pressure difference with the external atmospheric pressure. Under the effect of this pressure difference, water is forced into the inlet and then discharged from the outlet. With the kinetic energy transmitted by the motor, water is continuously sucked in and discharged, forming a relatively stable flow.
15
1
Share

Where is the windshield washer fluid reservoir of Lavida located?

Lavida's windshield washer fluid reservoir is located in the front engine compartment, near the engine. Precautions for the reservoir: The reservoir is marked with a warning not to open the cap when the engine is at high temperature. Do not fill the car reservoir with ordinary water (tap water, mineral water). It is necessary to add automotive engine coolant (which does not freeze at 0 degrees and does not boil at 100 degrees). Coolant does not produce scale and ensures the cleanliness of the engine's water passages. The maintenance method for the car reservoir is as follows: Park the vehicle and turn off the engine. After the coolant temperature has dropped, open the expansion tank and add the radiator cleaner. Start the engine and let it idle for 5-10 minutes after the cooling fan starts working. Turn off the engine and remove the front bumper of the vehicle. When disassembling, make sure all fixing screws have been loosened, and then slowly disassemble from both ends to the middle, being careful not to break the fixing clips. Ensure that the coolant temperature has completely cooled down, then drain the radiator cleaner along with the coolant, and finally replace it with new engine coolant.
13
5
Share

Does using air conditioning consume more fuel in N gear or P gear?

If you are not leaving the car, using N gear is completely fine, but make sure to engage the handbrake properly to prevent the car from rolling. Power consumption of the air conditioning: Different cars have varying power requirements. For every 1 ton of refrigeration capacity, the car air conditioning consumes about 2 horsepower. To save space, car air conditioning condensers are usually designed to be smaller, and the operating environment temperature is relatively high. Therefore, to achieve the same cooling capacity, car air conditioning inevitably consumes more power compared to household air conditioning. Maintenance of car air conditioning: When using the air conditioning for the first time in summer, it is advisable to inspect the air conditioning system first. For example, check the refrigerant and whether the air filter is too dirty through the liquid storage tank, and see if there are any foreign objects in the radiator. Cleaning of car air conditioning: The air filter should be replaced regularly to prevent moldy odors from the air conditioning. Additionally, the condenser should be cleaned periodically, and the radiator should be removed for thorough cleaning.
20
2
Share

What Should Beginners Pay Attention to When Driving a Wuling Hongguang?

Beginners driving a Wuling Hongguang should pay attention to flat ground starting, brake-assisted starting, acceleration and gear shifting during startup, and parking methods. Flat ground starting method to note: Those unfamiliar with manual transmission vehicles may stall when starting on flat ground, especially beginners. First, start the vehicle in neutral, press the clutch, and shift into first gear. Then, lift the clutch pedal. When the clutch reaches the engagement point and you feel the car beginning to move, maintain the clutch at the semi-engaged state and gently press the accelerator to coordinate. This method makes stalling less likely during startup. Brake-assisted starting method to note: Brake-assisted starting means starting the engine while pressing the foot brake or using the handbrake. Release the brake once the car shows signs of moving forward to complete the starting operation. Acceleration and gear shifting during startup to note: Whether starting on flat ground or with brake assistance, once the car begins to move forward, gently press the accelerator and lightly release the clutch as the speed increases. In other words, you can press the accelerator while releasing the clutch. If unsure, you can delay releasing the clutch by one or two seconds.
13
2
Share

Where is the charging port located on the Tianlu car?

It is a round hole, originally where the cigarette lighter was inserted. Remove the cigarette lighter and insert the pointed part of the car charger into it. If the indicator light is on, it means it can be used. Main functions of the USB port: Utilizing the standard power supply in the car, the USB port can be used to charge electrical devices or serve as a fixed power supply interface. The USB port is a type of vehicle transmission cable, featuring advantages such as fast transmission speed, ease of use, support for hot-swapping, flexible connection, and independent power supply. It is generally a universal interface for devices like USB drives and MP3 players. The USB port in the car can be used for: playing music from a USB drive, charging mobile phones and MP3 players, serving as a USB car cigarette lighter interface, connecting to electronic dog devices and dash cams, and charging laptops and tablets. Precautions for using the USB port: Charging should only be done when the car's engine is running to avoid damage to electrical devices due to unstable power supply. Do not connect too many devices to prevent overloading and damaging the car battery and alternator. Avoid using the USB port during thunderstorms to prevent lightning strikes. Do not use the USB port in damp environments, as rust or water stains may cause the USB drive to fail to connect properly.
11
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.