What is the general capacity of a car battery?

What is the function of the engine exhaust gas valve?

The function of the engine exhaust gas valve is to enable exhaust gas recirculation: 1. The engine control computer opens the solenoid valve at the appropriate time based on the engine's speed, load throttle opening, temperature, intake flow, and exhaust temperature; 2. Air from the intake pipe enters the EGR valve vacuum diaphragm chamber through the solenoid valve, and the diaphragm rod opens the EGR valve, allowing a small portion of the exhaust gas to enter the intake system through the EGR valve, where it mixes with the air-fuel mixture and enters the cylinder for combustion; 3. Excessive exhaust gas participating in recirculation will affect the ignition and performance of the air-fuel mixture, thereby affecting the engine's power, especially during idle, low speed, small load, and cold engine conditions, where the recirculated exhaust gas can significantly impact engine performance.

16

5

Share

What does it mean when the vehicle stability control system light is on?

Vehicle Stability Control, also known as ESP, is a type of active safety system in vehicles. It is an extension of the Anti-lock Braking System (ABS) and Traction Control System (TCS) functions. When the ESP light on the vehicle's dashboard illuminates, it alerts the owner that there may be a malfunction in the stability control system, requiring prompt inspection and repair. The causes of ESP failure are as follows: 1. ABS pump failure or issues with the ABS pump power and grounding circuits; 2. Loose sensor connectors or failure of a specific sensor; 3. Related fuse blown or burnt out; 4. Obstruction in system signal transmission; 5. False fault, where the system gives a false alarm—try pressing the off button to restart the system.

19

4

Share

What to Do When the Transmission Shows Overheating?

The following are the methods to deal with the engine malfunction indicator light: 1. Use fuel additives to clean the entire fuel system. 2. After cleaning the engine, use gasoline with a higher octane rating. 3. Use high-quality fuel additives to improve the cleanliness level of the fuel. 4. Replace the three-way catalytic converter. The reasons for the engine malfunction indicator light being on are as follows: 1. Sensor damage, poor contact, or signal interruption. 2. Poor engine maintenance. 3. Poor quality of fuel and engine oil. 4. Incomplete combustion of the air-fuel mixture. 5. Faulty spark plugs or ignition coils. 6. Fuel pump failure, clogged fuel lines, or blocked air filter.

18

0

Share

How to Open the Trunk of Toyota Prado?

To open the trunk of the Toyota Prado, simply pull the trunk handle located next to the license plate. Here are some details about the Toyota Prado: 1. The Toyota Prado 2700, also known as the Land Cruiser Prado, features a perfect streamlined body design. The significant gap between the wheel arches and tires highlights its climbing capability, making it suitable for various complex terrains. 2. While delivering robust power and off-road performance, the Toyota Prado 2700 also emphasizes active safety design and configurations. The system includes a Torsen central differential, which distributes torque between the front and rear axles in a 40:60 ratio. In case of slippage, the torque distribution ratio can adjust up to a maximum of 29:71.

15

3

Share

How to Read Tire Specification Parameters

Tire specifications can be found on the sidewall (tread pattern). The tire size specifications are expressed in millimeters as the section width and the percentage of the aspect ratio. This is followed by: tire type code, rim diameter (in inches), load index (allowable load mass code), and allowable vehicle speed code. The influence of tire specifications on other parameters is as follows: 1. The width of the tire is an important factor affecting the vehicle's fuel consumption and economic performance. The wider the tire, the larger the contact area with the ground, which correspondingly increases fuel consumption. 2. Aspect ratio: The lower the aspect ratio of a car tire, the greater the pressure it can withstand, and the higher its responsiveness, making it very quick to handle. However, it places higher demands on the elasticity and softness of the shock absorbers.

2

0

Share

How to Reset the Toyota Sienna Tire Pressure Light?

Toyota Sienna tire pressure light reset requires finding the vehicle information button on the vehicle display screen, entering the page, then selecting tire settings, and clicking the SET button to confirm. This will complete the tire pressure monitoring initialization, successfully resetting the tire pressure light. Common tire pressure reset methods: First, turn on the ignition switch, press and hold the tire pressure monitoring reset button until you hear a "beep" sound, then release it. The tire pressure monitoring system will store the current normal tire pressure data, automatically clear the original data, and finally, the dashboard warning light will turn off, completing the tire pressure reset. Tire Pressure Reset: Tire pressure reset is the operation of resetting the tire pressure monitoring system after resolving a tire pressure fault. Vehicles are usually equipped with a tire pressure monitoring system that alerts for tire leaks and abnormal tire pressure. The tire pressure monitoring indicator light will illuminate to ensure driving safety.

13

4

Share

What is the general capacity of a car battery?

What is the function of the engine exhaust gas valve?

What does it mean when the vehicle stability control system light is on?

What to Do When the Transmission Shows Overheating?

How to Open the Trunk of Toyota Prado?

How to Read Tire Specification Parameters

How to Reset the Toyota Sienna Tire Pressure Light?

How to Fix Sunroof Leakage in Tiguan?

Is a tire pressure of 2.6 too high in summer?

What to Do When the Built-in Tire Pressure Monitoring Sensor Runs Out of Power?

Is a car directly totaled if water reaches the dashboard?