What is the function of the Teana water pump vent?

1 Answers
McMarley
07/30/25 7:03am
The function of the Teana water pump vent is to exhaust high-temperature air and intake low-temperature air. Automotive engines widely use centrifugal water pumps, whose basic structure consists of components such as the water pump housing, connecting plate or pulley, water pump shaft and bearings or integrated shaft bearings, water pump impeller, and water seal device. It is a major component of the vehicle. The Teana has a length, width, and height of 4901mm, 1850mm, and 1450mm respectively, with a wheelbase of 2825mm. The front suspension of the Teana is a MacPherson strut independent suspension, and the rear suspension is a multi-link independent suspension with trapezoidal control arms. It is equipped with a 2.0L naturally aspirated engine, delivering a maximum power of 115kW and a maximum torque of 197Nm, paired with a continuously variable transmission.
Was this review help?
9
3
Share
More Forum Discussions

Should the Maxus G10 use 92 or 95 octane gasoline?

The Maxus G10 should use 92 octane gasoline, as this fuel grade is recommended in the vehicle's official user manual. In addition to checking the appropriate gasoline grade in the user manual, the Maxus G10 also indicates it on the fuel tank cap. The required gasoline grade can usually be determined by the engine's compression ratio. Vehicles with an engine compression ratio between 8.6-9.9 should use 92 octane gasoline, while those with a compression ratio between 10.0-11.5 should use 95 octane gasoline. If the compression ratio is even higher, 98 octane gasoline is recommended. However, with the application of new technologies, the compression ratio alone cannot determine the required gasoline grade, as high compression ratio engines can also be tuned to use lower octane gasoline. Other factors, such as ignition timing, turbocharging technology, and Atkinson cycle technology, also play a role. Generally, the higher the gasoline grade, the higher the octane number and the better the anti-knock performance. 92 octane gasoline contains 92% isooctane and 8% n-heptane, while 95 octane gasoline contains 95% isooctane and 5% n-heptane. If the Maxus G10 occasionally uses the wrong gasoline grade, simply switch back to the correct grade after the tank is empty. However, long-term use of the wrong gasoline grade can have the following effects: For vehicles recommended to use lower octane gasoline, using a higher octane grade will not cause damage, but the increased octane number may alter the fuel's ignition point, leading to delayed combustion in the engine. This reduces the engine's power output and thermal efficiency, resulting in poorer performance. For vehicles recommended to use higher octane gasoline, using a lower octane grade can cause engine knocking. The significantly lower octane number reduces the fuel's ignition point, causing premature ignition during the compression stroke. If combustion occurs before the spark plug ignites, resistance will arise during the upward stroke. This resistance makes the engine run very unstably. Mild knocking may only increase noise without obvious engine damage, but severe knocking indicates serious engine conditions. The vibrations not only affect driving stability but also cause abnormal wear on the piston and cylinder, potentially leading to cylinder scoring in severe cases.
13
1
Share

What is the displacement of the 4D26 engine?

The displacement of the Quanchai 4D26 engine is 2.59L. Below are the specific details about Quanchai engines: 1. Series and Power: Quanchai engines currently mainly include the 4A, 4B, and 4F series of National IV engines, as well as the 4D22E, 4D18E, 4D25, 4D26, 4D18F, and 422F series of National III diesel engines. The power of diesel engine products ranges from 15 to 380 horsepower. 2. Features: Quanchai engines are entirely fueled by diesel. They use a special type of internal combustion engine where the fuel burns inside. There are many types of internal combustion engines, with common gasoline and diesel engines being typical examples.
9
4
Share

How Often Should Polishing and Waxing Be Done?

Polishing and waxing should be done every 3 to 6 months. Both polishing and waxing can maintain the car's appearance and repair minor scratches. Very fine scratches, such as hairline scratches, can be removed by waxing. For relatively more severe scratches, polishing is needed to remove them. Relevant information is as follows: 1. Function: Waxing can serve as a polishing agent. When minor scratches appear on the car, sand wax can be used to polish and remove the scratches. Sand wax contains special abrasive particles that can easily and safely remove the oxidation film, fine scratches, spots, and stubborn stains on the car's surface, restoring the original charming luster and long-lasting beauty to the old, faded, and dull paint layer. 2. Repair: Polishing is a consumable repair method. Minor scratches can be repaired by polishing. By rotating the polishing disc, the oxidation layer, scratches, and stains on the car's paint surface can be polished, restoring the paint surface to a smooth and shiny state. A small amount of polishing is fine, and the car paint can withstand it.
11
5
Share

What does TEMP mean in car air conditioning?

Car air conditioning TEMP represents temperature. Here is the relevant introduction: 1. Brief introduction: temp is the abbreviation of temperature, meaning temperature, and is the button for adjusting the heating and cooling temperature of the air conditioner. 2. Air conditioning: Air conditioner (Air-Conditioner), that is, an air conditioning device, refers to equipment that artificially adjusts and controls parameters such as temperature, humidity, cleanliness, and air flow in the environment of buildings/structures. Most of them use refrigerant to evaporate or condense under the action of a compressor, thereby causing the surrounding air to evaporate or condense to achieve the purpose of changing temperature and humidity.
1
5
Share

Is the BMW 530li an imported model?

All BMW 5 Series models with the Li designation are produced by BMW Brilliance and are not imported vehicles. Differences between the imported BMW 530i and the domestic version: 1. Powertrain: The imported 5 Series has no difference from the BMW Brilliance 5 Series. The 530 model is equipped with a 2.0T high-power version engine, delivering 252Ps and 350Nm of torque, which is achieved at 1450 rpm, meaning it reaches this output with just a slight press of the accelerator. This engine features direct fuel injection and requires 95-octane gasoline, currently meeting the China VI emission standards. The transmission is the familiar 8AT, with rear-wheel drive, front double-wishbone suspension, and rear multi-link suspension, all independent. The official 0-100km/h acceleration time for this imported BMW 530i is just 6.2 seconds, which is very fast among 2.0T models, especially considering the car weighs nearly 1.7 tons. 2. Configuration: The central control area is well-organized, with a 10.2-inch multimedia screen at the top, featuring built-in GPS navigation, emergency call service, Bluetooth phone connectivity, 360° panoramic imaging, multimedia entertainment system, voice recognition control system, and in-car internet. The vehicle comes standard with a Harman Kardon audio system with 12 speakers. The three-spoke genuine leather steering wheel integrates cruise control, volume adjustment, phone functions, and is equipped with paddle shifters behind it. The instrument panel is fully digital with multiple theme options, measuring 12.3 inches, and can be optionally equipped with a HUD (Head-Up Display) function.
17
0
Share

What is the fuel tank capacity of the CFMoto Papio?

The fuel tank capacity of the CFMoto Papio is only 7 liters. The CFMoto Papio is equipped with a 124cc single-cylinder air-cooled engine, enhanced with fuel injection technology to meet current emission standards. It delivers a maximum torque of 8.3 Nm and achieves a maximum power of 7 KW. In terms of transmission, the 6-speed chain-driven transmission stands out for its reliability and smoothness, which goes without saying. Moreover, through continuous optimization by CFMoto, the potential of the engine and transmission system has been further unleashed. In comparison to other models in the same class, the CFMoto 650 TR-G has a fuel tank capacity of 22 liters. Ways to reduce motorcycle fuel consumption: Start gently and twist the throttle lightly. Shift gears in a timely manner on a geared motorcycle. Gear shifting should neither be too early nor too late. Generally, you can listen to the engine sound and refer to the tachometer, ensuring the engine RPM matches the vehicle speed. Excessive throttle or low engine RPM can lead to higher fuel consumption. Always monitor tire pressure, as proper tire pressure can help reduce fuel consumption! Both over-inflation and under-inflation of tires can increase fuel consumption. Minimize braking, but emergency braking is necessary when required.
3
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.