What is the function of the RES button on the steering wheel?

What is the Function of a Knock Sensor?

The functions of a knock sensor are as follows: 1. A knock sensor is a piezoelectric sensor that converts vibrations into voltage. 2. The knock sensor is usually installed on the car's generator to detect whether the engine may experience knocking, allowing the electronic control system to adjust the ignition timing to prevent knocking. Additional information: 1. The knock sensor is installed in the middle of the engine block. For a four-cylinder engine, it is installed between cylinders 2 and 3, or one between cylinders 1 and 2 and another between cylinders 3 and 4. Its purpose is to measure engine vibration and adjust the ignition timing when knocking occurs. 2. When the engine produces knocking, the knock sensor converts the mechanical vibration of the engine into a signal voltage and sends it to the ECU. The ECU then calculates and corrects the ignition timing based on its pre-stored ignition and other data to adjust the ignition timing and prevent knocking.

7

5

Share

Where is the ETC installed?

The ETC is generally installed in the upper middle part of the front windshield for passenger cars, while for large vehicles such as trucks and buses, it is installed in the lower middle part. The appropriate installation position should be no lower than 1.2 meters and no higher than 2.5 meters, with an installation angle between 30 to 90 degrees. For vehicles with factory-installed or aftermarket explosion-proof film, which may affect the signal transmission of the microwave communication link, the ETC should be installed in the microwave skylight zone. ETC stands for Electronic-Toll-Collection, meaning electronic toll collection system. To apply for ETC, the vehicle owner needs to provide their valid ID card and the original and photocopy of the vehicle registration certificate. If the application is made by someone other than the owner, the agent's valid ID card is also required. The photocopy of the vehicle registration certificate should include the page with the most recent annual inspection seal. Additionally, a bank card for deducting highway tolls is needed, and the vehicle must be registered under the name of an individual aged between 18 and 60. For company vehicles, the required documents include: An introduction letter from the vehicle owner (with company seal); photocopy of the organization code certificate or business license (with company seal); original ID card of the agent; original vehicle registration certificate; and the vehicle that needs to have ETC installed. Here are some precautions for installing ETC: Do not obstruct the driver's view. It is best to install it behind the rearview mirror: Many car models have a steeply inclined windshield, which can reduce the driver's field of vision. If the ETC is installed without considering this, it may increase the driver's blind spots. Installing it behind the rearview mirror on the right side can help avoid obstructing the view. Do not interfere with charging: The ETC electronic tag consumes power, but generally does not require charging or battery replacement because it has a solar panel on the back that can charge itself. Therefore, during installation, avoid the blackened areas on the windshield and positions that may block the solar panel. Once installed, do not remove it arbitrarily: The button in the middle of the adhesive is an anti-tamper rod connected to a switch. After the electronic tag is installed on the windshield, the anti-tamper rod is pressed in. If the tag is removed arbitrarily, the rod will pop out and trigger the switch, locking the electronic tag and rendering it unusable. In this case, you will need to visit an ETC service point to unlock it. This mechanism is designed to prevent multiple vehicles from sharing a single device.

2

3

Share

What to Do When the Car Displays an Oil Change Reminder?

When the oil warning light comes on, the first thing you should do is open the engine compartment and check if the oil has been completely used up. If it has, you should go to the nearest auto parts store to purchase oil as soon as possible and temporarily add it in. If you continue driving without oil, the lack of lubrication will cause the engine components to rub against each other and sustain damage. Below are some oil refill precautions: 1. The oil viscosity must be suitable. Different grades of oil have different characteristics, including varying low-temperature starting performance and high-temperature anti-wear and adhesion properties. Oil viscosity is inversely proportional to temperature. When the engine is cold, the oil viscosity is higher. If the oil chosen is too thick, it will place additional strain on the starter motor and battery. 2. Carbon buildup. As old oil becomes thinner with use, carbon buildup increases. Overly thin oil can lead to oil blow-by, causing more carbon buildup and significant power loss. When new oil is added, the engine may not immediately adapt to the oil's viscosity, potentially causing higher RPMs and increased engine noise.

10

3

Share

Does idling with the air conditioning on damage the car?

Idling with the air conditioning on does not damage the car. The main concern when idling with the air conditioning on is the water temperature, especially in older cars with mechanical fans. Mechanical fans are driven by the engine crankshaft, and at idle speed, the engine crankshaft rotates slower, causing the cooling fan to spin slower as well. Prolonged idling can lead to insufficient engine cooling, resulting in overheating. Below are the effects of idling with the air conditioning on: 1. Increased fuel consumption: The engine already consumes fuel while idling, and running the air conditioning requires the engine to power the compressor, which further increases fuel consumption; 2. Reduced battery life: The air conditioning blower is powered by the battery. At idle speed, the battery's charging efficiency is relatively low, and prolonged operation of the blower may lead to battery discharge, shortening its lifespan over time.

6

4

Share

What is the general tire pressure for a minivan?

If the minivan is an MPV, the appropriate tire pressure is between 2.6-3.0. For a vehicle carrying 7 passengers, the recommended tire pressure is around 2.8. However, tire pressure can fluctuate above or below the standard due to various factors such as tire condition, vehicle load, and seasonal changes. Additionally, different models have varying weights, which means the standard tire pressure for minivans may also differ. Additional information: 1. The standard tire pressure for a minivan can usually be found on the vehicle's B-pillar, fuel tank cap, the drawer next to the driver's seat, or in the vehicle's user manual. This standard tire pressure is detailed and specifies values for different passenger counts or cargo weights. 2. Tire pressure varies based on tire condition: (1) New tires: The pressure can be adjusted approximately 0.2bar higher than the standard tire pressure. (2) Old tires: The pressure should be slightly lower than the standard, and if severely worn, it should be set to the lower limit of the standard. (3) Soft tires (comfort-oriented treads): The pressure can be adjusted approximately 0.2bar higher than the standard. (4) Hard tires (performance-oriented treads): The pressure should be set to the lower limit of the standard.

18

0

Share

How to Measure the Air Flow Meter?

Air flow meter detection methods are as follows: 1. Measure the output voltage data during engine operation to determine: Check the dynamic signal voltage at the signal terminal of the connector. At engine idle, the standard voltage is 0.8-1.4V; when accelerating to full load, the voltage signal can approach 4V. If the voltage is not within this range, it may indicate damage to the air flow sensor itself or contamination, which can be resolved by cleaning. 2. Measure the sensor's output voltage to determine: Use a multimeter to test, with a general voltage value of 5V. Blow air into the sensor with a hair dryer—if the voltage changes with the amount of airflow, it is normal; if it remains unchanged or changes minimally, the flow meter is faulty and needs replacement. 3. With the engine running, unplug the air flow meter connector and observe changes in engine performance to determine: If the fault condition changes slightly, the air flow meter is functioning; if the fault disappears, the flow meter signal is deviating but not damaged; if the fault persists, the air flow meter is already damaged or has poor wiring.

9

2

Share

What is the function of the RES button on the steering wheel?

What is the Function of a Knock Sensor?

Where is the ETC installed?

What to Do When the Car Displays an Oil Change Reminder?

Does idling with the air conditioning on damage the car?

What is the general tire pressure for a minivan?

How to Measure the Air Flow Meter?

Where is the charging port for new energy vehicles?

What is the difference between diesel engine oil and gasoline engine oil?

Why Can't Spare Tires Be Used Long-Term?

Is the first maintenance of GAC Honda available nationwide?