What is the Function of LED Daytime Running Lights?

1 Answers
AshleyAnn
07/29/25 3:03pm
LED daytime running lights serve to enhance vehicle visibility during daytime driving in poor visibility conditions, thereby preventing accidents in advance and ensuring driving safety. Below is relevant information about LED daytime running lights: 1. Concept: LED daytime running lights are daytime driving signal lights installed at the front of the vehicle body, abbreviated as LED DRLs. They are called LED daytime running lights because they use LED light sources and are turned on during the day for daytime driving. 2. Application Background: To improve driving safety, the European Union mandated that starting from 2011, all new vehicles within the EU must be equipped with LED daytime running lights (Daytime Running Light, abbreviated as DRL).
Was this review help?
20
1
Share
More Forum Discussions

Where is the rearview mirror heating switch located on a BMW Mini?

The BMW Mini's rearview mirror heating button is a push-button type switch located on the control panel, featuring a square frame with three upward-curving arrows inside. Pressing this button activates the rearview mirror heating function. Principle of rearview mirror heating: Both side mirrors contain embedded heating elements (heating films). During rainy or snowy weather, when the driver activates the rearview mirror heating function, these heating elements rapidly warm up to a set temperature (typically between 35-60°C) within minutes, effectively defogging and defrosting the mirrors. The rearview mirror heating button icon should be distinguished from the front windshield defroster button: A fan-shaped symbol with three upward-curving arrows indicates the front windshield defroster, while a square frame with three upward-curving arrows represents the rearview mirror heating function.
5
3
Share

Why Can't the Trunk of the New Jetta Open?

Reasons why the trunk of the New Jetta cannot open: issues with the linkage rod or lock cylinder; not unlocked; mechanical component failure, etc. Here are the specific reasons: Linkage rod or lock cylinder issue: If you frequently use the key to open the trunk, the linkage rod may be disconnected. Go to a repair shop to have it fixed. If you always use the remote control to open the trunk, the lock cylinder might be dirty or rusty. Spray some rust remover into the lock cylinder a few times to open it. Not unlocked: The trunk is difficult to open because it hasn't been unlocked with the remote key. Before opening, it's best to press the unlock button on the key or check if the key battery is dead. If the battery is dead, replace it with a new one. Mechanical component failure: The trunk's wiring may be broken, or other trunk-related issues may prevent it from opening. It is recommended to go to a 4S shop for repair or replacement.
8
5
Share

Audi is the Light Factory, Then What is BMW?

Audi has earned the reputation as the "Light Factory" among car enthusiasts due to its outstanding lighting technology and design. In fact, Mercedes-Benz and BMW do not have such nicknames. Introduction to BMW: The history of BMW dates back to 1916. The company initially started as an aircraft engine manufacturer, headquartered in Munich, Bavaria. BMW's Logo: The blue and white BMW logo symbolizes a rotating propeller. However, the current BMW CEO has clarified that while people often associate the blue and white logo with a propeller, it actually represents Bavaria. BMW is headquartered in Munich, Bavaria, Germany, and the Bavarian state flag features blue and white colors. The name BMW stands for Bavarian Motor Works, representing Bavaria and Germany's most sophisticated engine technology.
1
1
Share

What causes the lean mixture in cylinder 1 of a Mercedes-Benz C200 at idle?

Mercedes-Benz C200 at idle when the mixture cylinder - too lean causes are as follows: Intake system air leakage: Can lead to a lean mixture, it is recommended to check whether the oil dipstick is inserted tightly, check whether the oil cap sealing gasket is aged, and check whether the exhaust valve is damaged; Incorrect air-fuel ratio: Resulting in a lean mixture, it is recommended to check whether the throttle is dirty, as dirt can also cause a lean mixture, check whether the fuel injector atomization is good, if it is equipped with a direct injection engine, it is recommended to clean the fuel injector, because the direct injection engine fuel injector is not easy to disassemble so it is difficult to observe, it is recommended to check whether the engine computer has any fault codes related to the oxygen sensor.
4
3
Share

What grade of gasoline is best for the BMW X5?

BMW X5 should use 95-octane gasoline, as this grade is recommended in the vehicle's official user manual. In addition to checking the appropriate gasoline grade in the user manual, you can also find it on the fuel tank cap, which will be clearly marked. Typically, the gasoline grade can also be determined based on the engine's compression ratio. Vehicles with an engine compression ratio between 8.6-9.9 should use 92-octane gasoline, while those with a compression ratio between 10.0-11.5 should use 95-octane gasoline. If the compression ratio is even higher, 98-octane gasoline is recommended. However, with the application of new technologies, the compression ratio alone cannot determine the gasoline grade, as high-compression engines can also be tuned to use lower-octane gasoline. Other factors, such as ignition timing, turbocharging technology, and Atkinson cycle technology, also play a role. Generally, the higher the gasoline grade, the higher the octane rating and the better the anti-knock performance. 92-octane gasoline contains 92% isooctane and 8% n-heptane, while 95-octane gasoline contains 95% isooctane and 5% n-heptane. If you occasionally use the wrong gasoline grade in your BMW X5, simply switch back to the correct grade after the current tank is used up. However, long-term use of the wrong gasoline grade can have the following effects: Using a higher-octane gasoline in a vehicle designed for lower octane will not cause damage, but the increased octane rating can alter the fuel's ignition point, leading to delayed combustion in the engine. This reduces the engine's power output and thermal efficiency, resulting in poorer performance. Using lower-octane gasoline in a vehicle designed for higher octane can cause engine knocking. Because the octane rating is too low, the gasoline may ignite prematurely during the compression stroke before the spark plug fires. This premature ignition creates resistance during the upward stroke, making the engine run very unevenly. Mild knocking may only increase noise without significant engine damage, but severe knocking indicates serious engine issues. The vibrations not only affect driving stability but can also cause abnormal wear on pistons and cylinders, potentially leading to severe engine damage.
7
4
Share

Where is the catalytic converter located on the Haval H3?

The catalytic converter of the Haval H3 is located in the first drum section of the car's exhaust manifold, resembling the shape of a canteen. The catalytic converter is the most important external purification device installed in the automobile exhaust system. It converts harmful gases such as CO, HC, and NOx emitted from the car's exhaust into harmless carbon dioxide, water, and nitrogen through oxidation and reduction reactions. Composition of the catalytic converter: The catalytic converter generally consists of four parts: the shell, damping layer, carrier, and catalyst coating. Shell: Made of stainless steel to prevent oxide scale from falling off, which could clog the carrier. Damping layer: Composed of padding or wire mesh pads, it serves to seal, insulate, and secure the carrier. To protect the carrier from damage due to vibration, thermal deformation, and other factors, the padding is made of expanded mica and aluminum silicate fibers, bonded together with adhesive. Carrier: Made of honeycomb-shaped ceramic materials, although many are also made of metal (including stainless steel) materials. Catalyst: Composed of precious metals such as platinum, rhodium, and palladium, sprayed onto the carrier to form the purifying agent. Lifespan of the catalytic converter: The lifespan of a catalytic converter is generally between 80,000 to 100,000 kilometers. The actual lifespan depends on the car's usage conditions, and it is also somewhat related to the quality of the fuel used and the driving environment.
6
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.