What is the function of car front fog lights?

1 Answers
MorganLynn
07/29/25 11:37am
Here is an introduction to the functions of car front fog lights: 1. In foggy or rainy conditions where visibility is significantly affected by weather, they allow other vehicles to see your car. 2. Installed at the front of the car, slightly lower than the headlights, they are used to illuminate the road during rainy or foggy weather. 3. They can improve the visibility for the driver and other traffic participants, enabling oncoming vehicles and pedestrians to spot each other from a greater distance. Here are the operation methods for turning on the front and rear fog lights: 1. Lever-operated type: The fog lights are activated by rotating the switch on the lever. When the button marked with the fog light symbol is turned to the ON position, the front fog lights turn on. Then, turning the button downward to the rear fog light position activates both the front and rear fog lights simultaneously. 2. Button-operated type: For models where the front and rear fog lights are turned on via buttons, there are fog light buttons near the dashboard or center console. Pressing the front and rear fog light buttons respectively will illuminate the front and rear fog lights.
Was this review help?
1
4
Share
More Forum Discussions

Will the Airbag Deploy If There's No One in the Passenger Seat?

If there is no one sitting in the passenger seat and the vehicle experiences a severe collision, the airbag may not necessarily deploy. The airbag will only deploy if the conditions for its activation are met. Below are the conditions for airbag deployment: 1. Appropriate speed and collision angle: The airbag requires an appropriate speed and collision angle to deploy. The collision must occur within approximately 60 degrees to the left and right of the vehicle's front center against a fixed object. 2. Speed exceeding 30 km/h: The airbag may deploy only if the speed exceeds 30 km/h. The speed referred to here is not the conventional understanding of vehicle speed but rather the speed at which the vehicle collides with a rigid fixed barrier in laboratory tests. In an actual collision, the vehicle's speed must be higher than the test speed for the airbag to deploy.
15
4
Share

Is the Invoice for a Financed Vehicle Given to the Owner?

Generally, the invoice for a financed vehicle is held by the bank. Once the loan is fully repaid, the owner can go through the release of mortgage process, after which the invoice and other documents will be returned to the owner. Below are the details: Vehicle Invoice: After the payment is made to the 4S store as required, the 4S store will issue the motor vehicle invoice to the customer. The invoice consists of six copies, with the first, third, and fourth copies given to the customer. Procedure Introduction: After completing the above procedures for installment car purchase, the vehicle needs to be mortgaged. The vehicle registration certificate (green book), vehicle invoice, insurance policy, driving license, ID card, and household registration booklet must be submitted to the bank. After the mortgage is processed, the bank will return the driving license, ID card, household registration booklet, and compulsory insurance policy. Once the loan is fully repaid, the owner can go through the release of mortgage process, and the invoice and other documents will be returned.
10
3
Share

Is an ID card required for driver's license renewal?

When applying for a driver's license renewal upon its expiration, you must submit your ID card or temporary ID card; a household registration booklet is not acceptable. Below is relevant information about driver's license renewal: Materials: For driver's license renewal, you need to bring the original ID card, the original driver's license, the "Motor Vehicle Driver's Physical Condition Certificate," and confirmation that all traffic violations and accidents have been processed. Notes: Motor vehicle drivers should apply for renewal at the vehicle management office where the driver's license was issued within 90 days before the expiration of the current license. If the driver's license has been expired for more than one year without renewal, it will be revoked. If the driver's license has been expired for more than one year but less than two years, passing the subject one exam can restore the license to normal use; if it has been revoked for more than two years, you will need to reapply for a new license.
4
4
Share

Will the engine stall if the car is in neutral without pressing the clutch?

Shifting to neutral without pressing the clutch will not cause the engine to stall. This is because when the car is in neutral coasting, the connection between the engine and the drive wheels is lost, and the transmission is completely disengaged from the drive wheels. In this state, not pressing the clutch will not stall the engine. Below are detailed explanations of neutral gear and the clutch: Neutral Gear: Neutral gear typically refers to the state where the vehicle's gearshift lever is not engaged in any forward or reverse gear, and the transmission is completely separated from the drive wheels. In manual transmissions, neutral is in the middle position, while in automatic transmissions, it is indicated by the 'N' symbol. Clutch: The clutch in a vehicle is located inside the flywheel housing between the engine and the transmission. The clutch assembly is secured to the rear plane of the flywheel with screws, and the output of the clutch is the input shaft of the transmission.
7
0
Share

Where is the crankcase ventilation valve located?

The crankcase ventilation check valve is installed on the valve cover. It automatically controls the circulation volume of crankcase blow-by gas based on changes in intake vacuum under different engine operating conditions. If the crankcase ventilation check valve is damaged, it will cause increased pressure inside the crankcase, accelerated engine oil consumption, and also affect exhaust emissions. Function of crankcase ventilation valve: During the power stroke of the piston, some high-temperature, high-pressure exhaust gases in the cylinder (which increase with vehicle age) will leak down into the crankcase through the piston ring gaps. This gradual accumulation will cause pressure to rise inside the crankcase. Therefore, a ventilation system needs to be designed to gradually release this pressure while maintaining reasonable crankcase pressure levels. Composition of crankcase forced ventilation system: When referring to the crankcase forced ventilation system, people usually think of the oil-gas separation system and crankcase pressure control system. However, a complete crankcase forced ventilation system should include five parts: ventilation chamber, oil-gas separation system, crankcase pressure control system, oil return chamber, and breather pipe. Among these, the ventilation chamber and oil return chamber are generally arranged in the engine block, running through the cylinder head, engine block, and crankcase. The oil-gas separation system and crankcase pressure control system are particularly important in the entire system.
15
3
Share

Do You Need to Press the Brake When Shifting in a Manual-Automatic Transmission?

No Generally, shifting gears in a car does not require pressing the brake. However, the only exception is when shifting from the P (Park) gear to other gears in an automatic transmission, where pressing the brake is necessary. Scenarios where braking is required for automatic transmission shifting: In an automatic transmission, pressing the brake is mandatory only when shifting from the P gear to other gears. Switching between other gears does not strictly require pressing the brake. After starting the engine in the P gear, shifting to any other gear (D, N, R) requires pressing the brake. If the brake is not pressed, the gear lever cannot be moved because of a safety lock mechanism installed here. Manual transmission shifting operation: Shifting gears in a manual transmission does not require pressing the brake. While shifting, coordinate the clutch and accelerator properly: press the clutch pedal all the way down, release the accelerator pedal immediately, and then quickly shift to the desired gear. After shifting, release your hand from the gear lever promptly; keeping it on the lever for too long can easily damage the gear lever.
12
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.