What is the function of an engine condenser?

1 Answers
KaiMarie
07/29/25 3:50pm
The function of the condenser is to dissipate heat and cool down the high-temperature, high-pressure refrigerant vapor discharged from the compressor, causing it to condense into a high-pressure liquid refrigerant. The gaseous refrigerant is liquefied or condensed in the condenser. When the refrigerant enters the condenser, it is almost 100% vapor, but when it leaves the condenser, it is not 100% liquid, as only a certain amount of heat energy is discharged from the condenser within a given time. Condenser Introduction: The condenser is a component of the air conditioning system that quickly transfers heat from the tubes to the surrounding air. It is mostly placed in front of the car's radiator and is a device that converts gas or vapor into liquid. After being throttled by the expansion valve, it becomes a low-pressure liquid and is sent into the evaporator, where it absorbs heat and evaporates into low-pressure vapor, completing the refrigeration process. Function of the Condenser: To dissipate heat and cool down the high-temperature, high-pressure gaseous refrigerant discharged from the compressor, causing it to condense into a medium-temperature, high-pressure liquid refrigerant.
Was this review help?
5
5
Share
More Forum Discussions

What kind of transmission does the Lavida automatic use?

The Lavida 1.6 automatic model is equipped with an Aisin 6-speed automatic transmission with manual shift mode. Introduction to the transmission: The transmission is a gearbox that changes the transmission ratio and direction of motion. It is located between the clutch and the central drive. Functions of the transmission: The main functions are to change the driving force and speed of the vehicle (shifting) while keeping the engine speed and torque unchanged; to allow the vehicle to reverse (direction change); and to enable the engine to stop without stalling (neutral gear). According to the transmission type, gear transmissions can be divided into three types: two-shaft, three-shaft, and combined. The two-shaft type has two main shafts (excluding the reverse shaft) and only goes through one pair of gear reduction. The three-shaft type has three main shafts (input shaft, intermediate shaft, and output shaft) and goes through two pairs of gear reduction. The combined type consists of two transmissions connected in series or parallel to obtain more gears with fewer gears.
2
2
Share

What are the techniques for steering the wheel when learning to drive?

The techniques for steering the wheel are as follows: Holding the steering wheel: Grip the steering wheel firmly with both hands to ensure body support points and hand grip points. Controlling the wheel with these three points allows for stable handling. The position of your hands on the steering wheel is also crucial; hold it in a 'nine-fifteen' position for maximum stability. Turning left: When making a left turn while driving, use your left hand to steer the wheel to the left, with your right hand assisting in pushing it leftward. After the turn, use your right hand to steer the wheel back to the right to align the vehicle straight ahead. Turning right: When making a right turn, use your right hand to steer the wheel to the right, with your left hand assisting in pushing it rightward. After the turn, use your left hand to steer the wheel back to align the vehicle straight ahead. Avoid incremental steering: Do not turn the wheel little by little, commonly known as 'feeding the wheel,' as this makes it harder to control direction in emergency situations.
16
1
Share

What type of fuel should the Enclave GX use?

The Enclave GX is recommended to use 95 or higher octane fuel for optimal performance. Enclave gasoline compression ratio: "The higher the compression ratio, the higher the required gasoline octane rating. A compression ratio of 7.5-8.0 should use 90-93 octane gasoline; a compression ratio of 8.0-8.5 should use 90-93 octane gasoline; a compression ratio of 8.5-9.0 should use 93-95 octane gasoline; a compression ratio of 9.5-10.0 should use 95-97 octane gasoline." (The Enclave has a compression ratio of 9.5), while the manual specifies 92 or above, but recommends 93 and 97. Gasoline grade categories: Gasoline has a high octane number (anti-knock combustion performance) and is divided into grades such as 90, 93, 95, and 97 based on the octane value. Gasoline is refined from various gasoline components obtained through petroleum refining, including straight-run gasoline components, catalytic cracking gasoline components, and catalytic reforming gasoline components, blended with high-octane components. It is primarily used as fuel for spark-ignition internal combustion engines in automobiles.
5
5
Share

Can a scooter fan be washed?

Scooter fans can be washed. Here is an introduction to the daily maintenance of scooters: Engine oil change: The frequency of engine oil change is every 800-1500km. When changing, use a unified engine cleaner to wash once (35 yuan/500CC, one bottle can be used three times). When changing, drain 30% of the oil, then add the unified engine cleaner (160 ml), start the engine and run it for 5 minutes, drain it all, blow high-pressure air from the oil filling port to blow out the residual oil in the gearbox, and then add new oil. Air filter: The cleaning frequency of the air filter is every 2000km. Because the position of the air filter on a scooter is lower than that of a cross-type motorcycle, and the air intake direction is generally horizontal (cross-type motorcycles are generally upward), the filter gets dirtier than that of cross-type motorcycles during driving. Spark plug: Spark plugs should be replaced every 20,000 kilometers. In the market, you can find: CR6E, CR7E, CR8E, CR9E. The number in the middle represents the heat value. If it is a high-compression ratio engine, it is recommended to use a high heat value spark plug. This can improve power and save fuel.
6
5
Share

Can Brushed Wheels Be Partially Repaired?

Brushed wheels can be partially repaired if the damaged area is small. Repair Methods for Brushed Wheels: Brushed wheel repairs are generally divided into partial repair and re-brushing. If the damaged area is small, partial repair can be performed. Although partial repair cannot restore the fine grain patterns of the wheel, the brightness and quality of the wheel remain unaffected after the repair. Additionally, partial repair is much cheaper than re-brushing the entire wheel. If the damaged area is large, the entire wheel must undergo re-brushing, which involves removing a layer of the damaged metal surface using a CNC brushing machine. After re-brushing, the wheel will regain its original metal grain patterns. However, each re-brushing process affects the wheel's quality, so multiple re-brushing repairs are not recommended. Definition of Wheel Brushing: Wheel brushing is a special surface treatment process that creates linear patterns on the wheel's surface through grinding, enhancing its decorative appeal. Car owners often choose brushed wheels because they appear to have a two-tone effect and a shiny, dynamic look.
5
5
Share

Where is the flasher relay located on the Baojun 730?

The flasher relay of the Baojun 730 is located in the control cabinet or control box. You can identify the actual component by referring to the following characteristics of relays. Introduction to relays: As an electrical control device, a relay is connected in a circuit to form two control systems: the control system (also known as the input circuit) and the controlled system (also known as the output circuit). You can trace the circuit to locate it. Generally, a relay has several main contacts plus two coil contacts, resembling a contactor. The main contacts are connected to the controlled system, while the coil contacts are connected to the control system. However, the contacts of a relay are usually visible, so you should be able to identify it based on this feature. Working principle of relays: When a certain voltage or current is applied to both ends of the electromagnetic relay coil, the magnetic flux generated by the coil passes through the magnetic circuit composed of the iron core, yoke, armature, and working air gap. Under the action of the magnetic field, the armature is attracted to the pole face of the iron core, thereby pushing the normally closed contacts to open and the normally open contacts to close. When the voltage or current at both ends of the coil falls below a certain value, and the mechanical reaction force exceeds the electromagnetic attraction force, the armature returns to its initial state, causing the normally open contacts to open and the normally closed contacts to close.
13
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.