What is the function of an automotive air conditioning dryer?

How to Deal with Water Accumulation Inside the Car?

Here are the situations and solutions for water accumulation inside the car: 1. Water accumulation in the doors: Due to deformation of the window glass sealing strips, water may enter the doors. It is necessary to promptly check whether the sealing strips are damaged. 2. Water accumulation in the trunk: Poor sealing of the trunk sealing strips and rear tail light seals can lead to water accumulation inside the car. If water is found entering the trunk, the sealing strips should be replaced immediately, and the sealing of the lights should be checked. 3. Water accumulation under the driver's feet: The car chassis is equipped with drainage holes. If the rubber rings of the drainage holes are damaged or fallen off, water from the road may splash into the car. It is necessary to promptly check whether the area under the floor mat is damp. If water accumulation is found, the sponge under the floor mat should be removed and dried to prevent rainwater from soaking the car chassis.

3

1

Share

What is the Appropriate Horsepower When Buying a Car?

Generally, family cars have a horsepower range of 100-150 PS, mainly featuring 1.6L and 1.4T engines. Naturally aspirated engines tend to have much lower torque, usually around 150 NM, which is relatively sufficient for household use. Below is some relevant information about engine power: 1. Power follows the laws of physics: The power output of an engine follows the laws of physics, showing a trend of increasing from low to high and then decreasing. 2. Good acceleration: Given similar power levels, how early the engine's maximum power/torque arrives and how long it can be maintained often determines whether a car's acceleration performance is good enough. It's important to note that higher horsepower is not always better.

16

2

Share

Will changing car color with film result in a fine?

Changing a car's color with film without completing the alteration registration will result in a fine. Here are the relevant regulations: 1. The "Road Traffic Safety Law" stipulates: No unit or individual may assemble motor vehicles or alter the registered structure, construction, or characteristics of a motor vehicle without authorization, including changing the model number, engine number, chassis number, or vehicle identification number. 2. Driving an illegally modified motor vehicle on the road: The traffic management department will detain the vehicle, confiscate illegal modifications, order restoration to the original condition, and impose fines. For illegally modified motor vehicles, the traffic management department will not issue a safety inspection certificate. 3. Exceeding the speed limit: The traffic management department will impose fines and may revoke the driver's license. If it constitutes a violation of public security management, the public security authority will impose penalties such as fines or detention in accordance with the "Public Security Administration Punishment Law."

16

3

Share

What Causes a Car Not to Start?

There are several common reasons why a car may fail to start: 1. Low battery voltage: This can cause the vehicle to show no response when starting, and the starter motor may not work. To determine if this is the issue, turn on the ignition and observe whether the dashboard lights dim significantly during the starting attempt. If the battery is confirmed to be dead, jump-starting the vehicle or replacing the battery can resolve the issue. 2. Faulty fuel pump: If the fuel pump is damaged, fuel from the tank cannot be supplied for combustion. To check this, turn on the ignition and listen for the sound of the fuel pump operating inside the car. If no sound is heard, the fuel pump may need replacement. If the fuel pump is not completely damaged, tapping the bottom of the fuel tank with a hard object like an iron rod might temporarily allow the car to start. Besides a faulty fuel pump, the issue could also stem from a damaged fuel pump control unit or relay. 3. Damaged crankshaft or camshaft position sensor: If these sensors fail, the engine cannot detect the top dead center of the first cylinder, preventing the car from starting. A diagnostic tool is required to read the engine's fault codes and identify the exact issue. 4. Lack of cylinder compression: This can also prevent the car from starting. In such cases, further engine disassembly is necessary to diagnose the root cause.

2

1

Share

What happens if you continue driving after running out of engine oil?

Continuing to drive a car without engine oil will firstly result in poor lubrication performance, and secondly may lead to severe engine seizure due to lack of lubrication. The less oil remains, the more serious the consequences will be. When the engine is restarted, dry or semi-dry friction will occur between the cylinder and piston, accelerating component wear and significantly increasing starting resistance, making it difficult to start. Here are more relevant details about engine oil's main functions: 1. Lubrication: The primary function of engine oil is to properly lubricate engine components such as pistons and bearings. 2. Sealing: During the power stroke, it prevents high-temperature, high-pressure gases in the combustion chamber from leaking into the crankcase through the gap between piston and cylinder. 3. Heat dissipation: When the engine operates at high speeds, friction between components generates substantial heat, which is absorbed by oil flowing through component gaps and then dissipated through the oil pan or oil cooler. 4. Rust prevention: Engine oil protects metal components from corrosion. 5. Cleaning: It filters out impurities and metal wear particles generated during engine operation through the oil filter, maintaining the lubrication system's cleanliness.

19

2

Share

Do I need to file for record when changing halogen lights to LED lights?

Converting the original halogen lights to LED bulbs does not require filing with the vehicle management office. Below are the differences between halogen lights and LED lights: 1. Halogen lights: Halogen lights are essentially incandescent bulbs filled with inert gas to extend the filament's lifespan. The light emission of halogen lights involves three physical processes: electrical energy - thermal energy - light energy, resulting in relatively high energy consumption. Halogen lights emit yellow light. The advantages of halogen lights include strong penetration and relatively low cost, making them easy to replace; however, their disadvantages include low brightness and a relatively short lifespan. 2. LED lights: LED lights can directly emit red, yellow, blue, green, cyan, orange, purple, white, and other colors of light. LED lights, also known as light-emitting diodes, can convert electrical energy directly into light energy, achieving an energy conversion efficiency of up to 90%. White light is typically used in vehicles. The advantages of LED lights include very high brightness, versatile design shapes, energy efficiency, environmental friendliness, long lifespan, small size, etc.; however, their disadvantages are weaker penetration compared to halogen lights and complex technology leading to higher costs.

2

4

Share

What is the function of an automotive air conditioning dryer?

How to Deal with Water Accumulation Inside the Car?

What is the Appropriate Horsepower When Buying a Car?

Will changing car color with film result in a fine?

What Causes a Car Not to Start?

What happens if you continue driving after running out of engine oil?

Do I need to file for record when changing halogen lights to LED lights?

What Causes a Clicking Sound When Accelerating Hard?

What is the dumbest way to make a right-angled turn?

How to Deal with Abnormal Noise from the Rear Axle of a Car?

How deep is the sidewall damage allowed for Continental tires?