What is the fuel tank capacity of the Wuling Zhiguang?

When will the 2020 Tiggo 8 be launched?

Tiggo 8 is a mid-size SUV under Chery Automobile. The current model on the market is the 2020 version, which was launched in June 2020. Although there is no news about the new model's facelift yet, according to the general facelift rules, the 2021 Tiggo 8 will be launched in June 2021. Below is the relevant introduction of Tiggo 8: 1. Exterior design: Since the current Tiggo 8's exterior design has not changed much compared to the 2019 model, the 2021 Tiggo 8's appearance will undergo a relatively obvious upgrade. The front face adopts Chery's latest design language, making the whole vehicle more fashionable and dynamic, better meeting the aesthetic requirements of Chinese consumers for SUV models. 2. Powertrain: The 2021 Chery Tiggo 8 continues to be equipped with two turbocharged engines, the 1.5T and 1.6T. The 1.5T model has a maximum horsepower of 156 and a peak torque of 230 Nm.

14

0

Share

What are the differences between the Red Badge Civic and the regular version?

Here are the differences between the Red Badge Civic and the regular version: 1. Performance difference: The performance of the Red Badge Civic is significantly stronger than that of the regular Civic. 2. Appearance difference: The emblem of the Red Badge Civic is also different from the regular Civic. The Red Badge Civic features a honeycomb-style front grille, four license plates mounted front and rear, a dual-exit exhaust at the rear, and a 'red' badge. 3. Engine difference: The Red Badge Civic is equipped with a 2.0T L4 engine, delivering a maximum horsepower of 310 hp and a maximum torque of 400 Nm. It is paired with a 6-speed manual transmission and features a front-wheel-drive system, achieving 0-100 km/h acceleration in just 5.7 seconds. The regular Civic comes with a 1.0-liter turbocharged engine producing 125 hp and 173 Nm of maximum torque, with a maximum power at 5500 rpm, and a 1.5-liter turbocharged engine offering 177 hp and 226 Nm of maximum torque.

4

3

Share

How to Reset the Tire Pressure on a Subaru Outback?

To reset the tire pressure on a Subaru Outback, follow these steps: 1. Press the vehicle's one-touch start button to power on the vehicle; 2. Press the mode button on the right side of the multifunction steering wheel; 3. The central instrument panel will display the vehicle's tire pressure information; 4. Press the cancel button on the left side of the multifunction steering wheel to remove the tire pressure display; 5. Observe the vehicle's instrument panel to confirm that the tire pressure light has been reset. Taking the 2020 Subaru Outback as an example, its body structure is a 5-door, 5-seat SUV crossover, with body dimensions of: length 4835mm, width 1840mm, height 1673mm, wheelbase 2745mm, minimum ground clearance 213mm, fuel tank capacity 60L, luggage compartment capacity 512 to 1801L, and a curb weight of 1624kg.

4

1

Share

What brand of engine does Geely use?

Geely's engines are independently developed by Geely Auto, so they are domestically produced engines. Geely's models use self-developed engines. For example, the Emgrand uses the JLY-4g15 engine model, with a maximum power of 80kW, maximum horsepower of 109, and maximum torque of 140N·m. Here are some daily maintenance methods for Geely's engines: Use lubricating oil of the appropriate quality grade. For gasoline engines, choose SD--SF grade gasoline engine oil based on the additional devices in the intake and exhaust systems and usage conditions. For diesel engines, select CB--CD grade diesel engine oil according to mechanical load, with the selection standard not lower than the manufacturer's requirements. Regularly change the oil and oil filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, performance deteriorates, causing various problems for the engine. To avoid malfunctions, change the oil regularly based on usage conditions and maintain an appropriate oil level. When oil passes through the fine holes of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter is clogged and oil cannot pass through, the filter may burst, or the safety valve may open, allowing oil to bypass through the bypass valve, bringing contaminants back to the lubrication areas and accelerating engine wear and internal contamination. Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal particles from component wear to form sludge. Small amounts remain suspended in the oil, while larger amounts precipitate, clogging filters and oil passages, making engine lubrication difficult and causing wear. Regularly use a radiator cleaner to clean the radiator. Removing rust and scale not only ensures the engine operates normally but also extends the overall lifespan of the radiator and engine.

16

3

Share

Why does the Q5 sunroof make noise on sunny days?

Solution: Adjust the sunroof by moving it up, down, forward, and backward. Apply 3M double-sided tape in various places. When opening the sunroof and manually tapping it, noticeable shaking was observed at the rear. Loosen the six sunroof fixing screws, forcefully push the rear of the sunroof upward to its limit, then slightly tighten the rear screws. Visually, the rear should be slightly higher than the fixed position. Next, adjust the front of the sunroof downward slightly, ensuring it is visually just below the roofline. The goal is to make the rear of the sunroof tilt upward as much as possible. After a few days of driving, the noise should disappear. Below is an introduction to the Q5: 1. Powertrain: Equipped with a 2.0TFSI inline-four engine paired with a 7-speed Stronic dual-clutch transmission, it delivers ample power, smooth gear shifts, and quick acceleration. Users praise its strong sense of push-back. 2. Interior: The domestic Q5 features a rationally designed and clean interior layout, with rich and practical configurations and a strong technological feel. The cabin craftsmanship is refined, and the materials used are of high quality.

19

4

Share

Should Shock Absorbers Be Replaced Individually or in Pairs?

Shock absorbers should be replaced in pairs. They are used to dampen the oscillations from the spring's rebound after absorbing shocks and to mitigate impacts from the road surface. The reasons for replacing shock absorbers in pairs are: 1. Shock absorbers from different batches may have varying hardness levels; 2. There can be significant performance differences between old and new shock absorbers; 3. In emergency situations requiring sudden steering, if the shock absorbers have different elasticity, it may increase the risk of vehicle rollover. The functions of shock absorbers include: 1. Buffering the movement of the vehicle's center of gravity and conserving energy; 2. Reducing wind resistance and lessening the impact of changes in the vehicle's center of gravity on the tires. The steps for replacing shock absorbers are: 1. Remove the shock absorber along with the spring, then use a spring clamp to secure the spring; 2. After replacing the shock absorber, release the spring clamp and reinstall both components together.

18

1

Share

What is the fuel tank capacity of the Wuling Zhiguang?

When will the 2020 Tiggo 8 be launched?

What are the differences between the Red Badge Civic and the regular version?

How to Reset the Tire Pressure on a Subaru Outback?

What brand of engine does Geely use?

Why does the Q5 sunroof make noise on sunny days?

Should Shock Absorbers Be Replaced Individually or in Pairs?

What is the fuel consumption of the Toyota 2700?

How to Measure Tire Size in Inches

How to Turn on the Heating in Tiggo 8?

Why does the car dashboard show abnormal tire pressure?