What is the fuel tank capacity of the Teana in liters?

2 Answers
SanVictoria
07/28/25 9:03pm
The currently available Teana has 6 models, all with a fuel tank capacity of 61.3 liters. The vehicle is equipped with two types of engines: a 2.0-liter naturally aspirated engine and a 2.0-liter turbocharged engine. All models come with either a CVT continuously variable transmission (simulating 8 gears) or a CVT continuously variable transmission. All models feature front-engine, front-wheel-drive configuration. Among vehicles in the same class, the 2021 Teana has a fuel tank capacity of 61.3 liters, the 2021 Camry has a 60-liter fuel tank, and the 2022 Passat has a 68.5-liter fuel tank. During actual refueling, the amount of fuel might exceed the calibrated capacity. This is because the fuel tank capacity specified by the manufacturer is measured from the bottom of the tank to the safety limit. There is additional space from the safety limit to the tank opening, which is designed to allow for fuel expansion when temperatures rise, preventing overflow. If fuel is filled up to the tank opening during refueling, the actual amount of fuel added may exceed the calibrated tank capacity. To check the remaining fuel level, owners can observe the fuel gauge on the right side of the instrument panel, marked with E and F. When the pointer is near E, it indicates low fuel, and when it is close to F, it means the fuel level is sufficient.
Was this review help?
8
0
Share
Everett
08/12/25 1:44am
The Altima's fuel tank capacity is typically around 70 liters, which is a quite reasonable design. I remember when I used to drive an Altima, it was particularly worry-free on long trips—a full tank could cover over 800 kilometers, assuming a fuel consumption of 8 liters per 100 kilometers. The size of the fuel tank directly affects refueling frequency; a larger capacity means fewer trips to the gas station, especially suitable for those who frequently drive on highways. Additionally, Nissan has put effort into the material and shape of the fuel tank to reduce the risk of leaks and enhance safety. As someone who drives often, I believe fuel tank capacity and engine efficiency should be considered together when choosing a car, since fuel efficiency isn't just about the tank.
Was this review help?
12
4
Share
Expand All
More Forum Discussions

What causes the electric starter of a motorcycle to idle?

The reason is an electric starter slipping issue. The specific causes and solutions are as follows: Electric starter slipping: Since the electric starting device and the engine transmission adopt a very meshing method, during each electric starting condition, the electric starter overrunning clutch assembly moves and engages with the crankshaft starting gear, but fails to subsequently transmit power to the crankshaft. Sometimes, due to certain reasons, the electric starter overrunning clutch cannot properly engage with the crankshaft starting gear, causing the electric starter overrunning clutch assembly to idle and failing to effectively transmit power to the crankshaft starting gear, resulting in the electric starter slipping phenomenon. Solution: Check the battery to ensure its technical condition is good.
18
5
Share

Where Can I Get a Replacement Key for an Electric Door?

You can contact the manufacturer or the dealer to get a replacement car key. Electric doors feature a non-stop clutch mechanism and other characteristics: Non-stop Clutch Mechanism: In case of a power outage or other malfunctions that prevent the door from operating normally, simply use the clutch key to turn the electric door switch to the disengaged state, allowing manual control. The LED display can show customizable advertisements, which customers can modify themselves. Equipped with a microcomputer control system and advanced electric door navigation technology, the door can follow a predetermined path without any tracks. Other Features: It can automatically retrieve the predetermined route and correct errors to ensure the door follows the set path. It eliminates friction noise from the electric door and can withstand strong winds.
9
2
Share

What Causes the Fuel Gauge to Be Inaccurate After Replacing the Fuel Pump?

The fuel gauge inaccuracy is only related to the float (fuel sensor) and has nothing to do with the fuel pump. The fuel gauge detects the fuel level through the float: If the detection signal is distorted, the fuel gauge will show inaccurate readings. The tachometer is related to the generator, as its sampling part comes from the generator's neutral line, while the speedometer is closely connected to the speed sensor (on the transmission) and the instrument voltage regulator module. To address these fuel gauge issues, it is recommended to choose higher-quality gasoline when refueling, as cleaner gasoline reduces impurities in the fuel pump, thereby lowering the probability of fuel gauge malfunctions. In cases where the fuel level display is controlled by the computer: Computer signal failures may also cause inaccurate displays, but this is very rare.
4
4
Share

What are the types of handbrakes?

There are three types of handbrakes. The function of the handbrake: The parking brake, commonly known as the handbrake, provides resistance to the car when parked to prevent it from rolling. The parking brake, whether it's the handbrake or the parking gear in an automatic transmission, locks the drive shaft or the rear wheels. Types of handbrakes: Handbrakes are categorized into traditional handbrakes, foot brakes, and electronic handbrakes. The traditional handbrake is the parking brake commonly seen in most vehicle models, usually located where the driver's right hand naturally rests, behind the gear lever for easy access. The foot brake, as the name suggests, is operated by foot. The operation of this parking brake is similar to the handbrake—pressing the pedal engages the brake, and pressing it again releases the brake as the pedal automatically pops up. The electronic handbrake is activated or deactivated via a button. Additionally, electronic handbrakes often come with features like AUTO and HOLD, making them a very useful invention for those who prioritize comfort.
13
0
Share

Will the File Number Change When Renewing the License?

The file number on the driver's license will not change if it is renewed locally, but it will change if renewed in a different location. Documents required for renewal: Bring two copies of ID card, two 1-inch recent color photos without hats, original ID card, original driver's license, and a medical examination certificate from a county-level or above hospital (free medical examination is also available at the vehicle management office). Renewal and inspection must meet the following conditions: Holders of large passenger vehicle, tractor, city bus, medium passenger vehicle, or large truck driver's licenses have no points in the current scoring cycle, or holders of other types of driver's licenses have less than 12 points in the current scoring cycle; Holders of large passenger vehicle, tractor, city bus, medium passenger vehicle, or large truck driver's licenses who have points in a scoring cycle, and holders of other types of driver's licenses who have been involved in a traffic accident resulting in death and bear equal or greater responsibility without having their driver's license revoked, and have participated in the inspection education; The applicant has no pending road traffic safety violations or traffic accidents; The applicant's physical condition meets the driving permit requirements; The driver's license is not seized, detained, suspended, revoked, canceled, or withdrawn by law.
14
5
Share

What are the reasons for uneven groove depths in the friction lining of a hoist?

The uneven groove depths in the friction lining of a hoist may be caused by insufficient tension between the wire rope and the pulley groove leading to sliding friction (common phenomenon), inflexible or obstructed rotation of the pulley bearing causing the wire rope to move while the pulley moves intermittently, or loose pulley bearings. Technical requirements for friction lining in friction hoists: The allowable coefficient of friction should not be lower than the required value for the hoisting system using this friction lining, but it should not be less than 0.20 at minimum. The friction lining should have good thermal stability. Classification of friction lining: According to the wire rope groove, friction lining can be divided into single-groove and double-groove types. Based on the coefficient of friction, it can be classified into ordinary lining and high-friction lining.
8
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.