What is the fuel tank capacity of the SX4 S-Cross?

1 Answers
DiGabriella
07/29/25 10:28pm
The fuel tank capacity of the Suzuki SX4 S-Cross 2012 1.6L Manual Utility model is 50L. It is equipped with a 1.6L naturally aspirated engine and a 5-speed manual transmission (MT). The drivetrain is front-engine, front-wheel drive. The front suspension is MacPherson strut independent suspension, and the rear suspension is torsion beam non-independent suspension. In the same class, the Venucia D60 2021 1.6L Entry Manual Comfort model has a fuel tank capacity of 50L, while the Chery Arrizo GX 2021 Champion Edition 1.5L CVT Premium model has a fuel tank capacity of 48L. During actual refueling, the amount of fuel may exceed the nominal capacity. This is because the fuel tank capacity marked by automakers is measured from the bottom of the tank to the safe fill level, and there is additional space from the safe fill level to the tank opening. This space ensures that the fuel can expand when temperatures rise without overflowing. If fuel is filled up to the tank opening during refueling, the actual amount may exceed the nominal capacity. To check the remaining fuel level, drivers can observe the fuel gauge on the right side of the instrument panel, marked with E (Empty) and F (Full). When the needle is near E, it indicates low fuel, while near F means sufficient fuel.
Was this review help?
15
1
Share
More Forum Discussions

How to Replace a Car Taillight Lens?

Here is the tutorial for replacing a car taillight lens: 1. First, unlock the driver's door and open it. Locate the trunk release button on the lower left side of the door panel and press it to open the trunk lid. 2. After opening the trunk, remove the interior lining on the side of the taillight. Use a small flat-head screwdriver to gently pry open the clips securing the lining, then pull the lining aside. Be careful when prying the clips to avoid damaging the plastic fasteners. 3. There are three nuts securing the taillight assembly. Use a small ratchet with an 8mm socket to remove each nut one by one. Keep the nuts safely for reinstallation later. 4. The taillight wiring harness is relatively simple. Simply pull the wiring connector off by hand. If it's difficult to remove, gently pry it out with a small flat-head screwdriver. 5. After removing the taillight lens, you can take out the taillight assembly. Hold both sides of the taillight with both hands and gently pull outward while slightly wiggling it to separate the taillight from the car body. Be careful not to use excessive force. Once the taillight is removed, install the new taillight lens by following the reverse steps.
18
0
Share

How many liters of oil does a BMW X1 need for maintenance?

BMW X1 maintenance generally requires adding 4.5L of oil. Below is an introduction to the relevant knowledge about oil. 1. Function of oil: Oil is extremely important for engine operation as it is responsible for two major functions: lubrication and heat dissipation, which can be further divided into four specific roles: cooling the engine temperature, lubricating engine parts, cleaning engine impurities, and sealing the engine to maintain the combustion chamber's seal. 2. Oil classification: Mineral oil and synthetic oil. For family cars like the BMW X1, synthetic oil is generally chosen. 3. Oil change interval: Change every 5,000 kilometers.
3
1
Share

How to Install Warning Lights in a Manual Transmission Parking Lot?

Warning lights come standard with every vehicle and do not require installation. The warning alarm light, also known as the hazard lights or flashers, serves to alert, warn, and signal in the event of an accident or other emergency situations. Below are the methods to activate the warning lights: 1. The warning light is a red button, usually positioned in a prominent location on the center console, featuring a white double-triangle border on the surface, and the button is relatively large. 2. Press once to activate, and press again to deactivate when stopping. The hazard lights can be activated in the following situations: 1. When driving in foggy conditions, turn on the fog lights to alert passing vehicles. 2. In the event of a vehicle malfunction or traffic accident on the road, the hazard lights should be activated to warn other vehicles to stay safe. 3. When towing a malfunctioning vehicle, both the towing vehicle and the towed vehicle should turn on the hazard warning flashers to indicate that the vehicle is in an abnormal state. 4. When temporarily parked on the driving road, activate the hazard lights to alert other vehicles to be cautious. 5. When forming a convoy as permitted by the traffic police department, all vehicles within the convoy should activate their hazard lights.
6
0
Share

How to adjust the seats in Borgward BX5?

Borgward BX5 seat adjustment methods: 1. Open the car door: Locate the left button on the side of the front seats, which is used to set seat position memory. 2. Push the lower switch forward or backward: This adjusts the seat's forward and backward movement. 3. Push the lower switch up or down: This adjusts the seat's height. 4. Right switch: Adjusts the seat backrest angle. Below is an introduction to the Borgward BX5's function buttons: 1. The row of buttons directly below the central control screen are air conditioning buttons for adjusting the AC. 2. One-touch start button: Located above the right side of the gear lever. 3. Rearview mirror angle button: Found on the driver's side door, alongside the window control buttons.
15
5
Share

How many kilometers does the second maintenance of a new car require?

New cars generally require their second maintenance at around 10,000 kilometers. Here is some knowledge about car maintenance: 1. Meaning: The second-level maintenance of a car refers to the maintenance operations centered on inspection and adjustment for motor vehicles that have traveled a certain mileage. 2. Maintenance scope: Inspect and adjust the working conditions of the engine and electrical equipment, dismantle and clean the oil pan and oil filter, inspect and adjust the steering and braking mechanisms, dismantle and clean the front and rear hub bearings. Add lubricating oil, dismantle and inspect the tires, and perform tire rotation. 3. Maintenance purpose: Maintain the various components, mechanisms, and assemblies of the vehicle to ensure they have good working performance and normal operation.
1
5
Share

What is the function of ASC in cars?

ASC in cars refers to the Active Stability Control system function. The details are as follows: 1. ASC stands for Active Stability Control, and this button can activate the vehicle control system. ASC on means the system is enabled, while ASC off means it is disabled. 2. System function: The Active Stability Control system can accurately control vehicle movement based on the driver's intentions, road conditions, and the car's driving status, helping to prevent dangerous situations and thereby more effectively improving the car's handling stability and driving safety.
18
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.