What is the fuel tank capacity of the Honda Lingpai 1.8 in liters?

2 Answers
McAmy
07/24/25 5:44am
The fuel tank capacity of the Honda Lingpai 1.8 is 47L. Methods to check fuel tank capacity: The simplest way to check the fuel tank capacity of a car is to look at the fuel gauge, which is used to monitor the remaining fuel in the car's tank. It is usually displayed with a pointer, and most fuel gauges have five to six segments, each corresponding to a specific amount of fuel. Fuel tank capacities of other models: Generally, small cars have fuel tank capacities ranging from 35 to 45 liters, while mid-sized cars have capacities around 55 to 75 liters. For example, the Toyota RAV4 has a fuel tank capacity of 60L, the Toyota Yaris L has a capacity of 42L, and the Toyota Reiz has a capacity of up to 70L.
Was this review help?
5
1
Share
StDeclan
08/11/25 1:24am
I've been driving the Honda Lingpai 1.8 for quite a while now, and its 47-liter fuel tank makes daily use extremely convenient. For city commuting, a full tank can last over 400 kilometers, and it can even reach 500 kilometers with good road conditions or on highways. The average fuel consumption is around 8 liters per 100 kilometers, which is quite economical. The fuel tank is designed at the rear bottom of the car, so it doesn’t affect the rear seating space, and the spare tire area stays clean. During regular maintenance, I pay attention to the fuel pump inspection to prevent clogging from impurities. Before long trips, I make sure the fuel level is above half to avoid engine damage from low fuel. I recommend new owners develop the habit of using high-quality gasoline to enhance range and vehicle longevity. Overall, this fuel tank size is well-balanced and perfect for practical drivers like me.
Was this review help?
1
1
Share
Expand All
More Forum Discussions

Is replacing the rear axle considered a major repair?

Replacing the rear axle is considered a major repair. The rear axle refers to the rear drive shaft component of a vehicle's power transmission system. It consists of two half-axles that enable differential movement and also serves as a device to support the wheels and connect the rear wheels. Depending on the suspension type, rear axles can be classified as rigid or independent. The functions of the rear axle are: 1. To transmit the power from the engine, which comes through the clutch, transmission, and driveshaft, to the wheels via the differential, reducing speed while increasing torque; 2. To bear the load of the rear axle; 3. To transfer the reaction forces and moments from the road surface to the frame through the leaf springs.
13
3
Share

What is the method for adjusting car headlight height?

Adjusting car headlight height involves the following steps: 1. Locate the headlight height adjustment button in your vehicle; 2. Rotate upwards to lower the beam angle, rotate downwards to raise the beam angle; 3. Adjust the knob to your desired setting. Guidelines for high beam usage: 1. Use high beams when driving on unlit roads; 2. Use high beams when there are no oncoming vehicles; 3. Use high beams during nighttime driving when the approaching vehicle is beyond 150 meters. Hazards of high beam usage: 1. Causes temporary blindness to oncoming drivers during nighttime encounters; 2. Reduces perception of speed and distance; 3. Impairs judgment of road width.
17
2
Share

How many kilometers can the BYD Qin electric car run?

The pure electric mode of the BYD Qin can achieve a range of approximately 70 kilometers. Below is an introduction to the BYD Qin: 1. The BYD Qin is a plug-in hybrid model that adopts the 'dual-engine dual-mode' core power system. In pure electric mode, the BYD Qin achieves a range of 70 kilometers, with a fuel consumption of 1.6 liters per 100 kilometers. Its acceleration from 0 to 100 km/h in just 5.9 seconds demonstrates its excellent performance. 2. In tests where the battery was fully charged to 100% and then depleted to 5%, three BYD Qin vehicles achieved ranges of 66 kilometers, 92.3 kilometers, and 91.7 kilometers respectively, far exceeding the officially claimed range of 70 kilometers.
2
3
Share

How to Pry Open a Maintenance-Free Car Battery?

To pry open a maintenance-free car battery, follow these steps: Use a flat-head screwdriver to press against the battery's protective plate and pull firmly. Maintenance-free batteries feature a fully sealed structure designed in the 1990s and modern production techniques, characterized by: 1. Vibration resistance; 2. High-temperature resistance; 3. Compact size. Methods to repair maintenance-free batteries include: 1. Full charge-discharge repair: Fully charge the battery, then completely discharge it to restore functionality; 2. Water replenishment repair: Open the battery's top cover and inject a specific amount of distilled water into each cell; 3. Pulse repair: Use a specialized pulse repair device to eliminate sulfation through charge-discharge cycles.
7
4
Share

How to Turn Off the Cruise Control Indicator?

The method to turn off the cruise control indicator is: 1. Gently press the brake pedal, and the cruise control indicator light on the dashboard will change from green to white; 2. Remove your foot from the brake pedal, and the vehicle will enter a coasting state with gears engaged, gradually decreasing speed; 3. When the driver presses the brake pedal, the cruise control will automatically deactivate. The cruise control system, abbreviated as CCS, is also known as the cruise control driving device, speed control system, or autonomous driving system. Its function is to maintain the vehicle speed as set by the driver without the need to press the accelerator pedal, allowing the vehicle to travel at a constant speed. With this system, drivers no longer need to control the accelerator pedal during long highway drives, reducing fatigue and unnecessary speed fluctuations, which helps save fuel.
8
4
Share

How to Turn Off Daytime Running Lights?

The method to turn off daytime running lights is: 1. Insert the car key and turn it to the position where only the radio can be heard. Pull the switch on the left side of the combination switch toward the driver's direction while also pulling it downward, and hold it without releasing; 2. Turn on the car key, and after about 3 seconds, you will hear a beep, indicating that the operation was successful. The functions of daytime running lights are: 1. To enhance the visibility of the vehicle; 2. To reduce vehicle accidents and lower the probability of fatal crashes. Precautions for installing daytime running lights include: 1. When choosing the installation location, try to avoid high-temperature areas and places prone to water accumulation; 2. During wiring installation, ensure that the direction of the wiring harness interface and the daytime running light interface is not incorrectly connected.
15
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.