What is the fuel tank capacity of the GLC260L in liters?

2 Answers
JacksonFitz
08/31/25 7:02am
The fuel tank capacity of the GLC260L is 66 liters. This data is officially published, and owners who have purchased the GLC260L can also check it on the vehicle's configuration sheet. The dimensions are 4764mm (length) * 1898mm (width) * 1642mm (height). The GLC260L requires 95-octane fuel. The following four models: Mercedes-Benz GLC 2022 Facelift II GLC260L 4MATIC Luxury, Mercedes-Benz GLC 2022 Facelift III GLC260L 4MATIC Dynamic, Mercedes-Benz GLC 2022 Facelift II GLC260L 4MATIC Dynamic, and Mercedes-Benz GLC 2022 Facelift GLC260L 4MATIC Luxury, all have a fuel consumption of 8.55L per 100km. A full tank can cover a distance of 771km. During daily driving, it is essential to monitor the remaining fuel level in the tank. This is usually done by observing the fuel gauge inside the car. If there are no other issues, the fuel level will be accurately reflected on the gauge. The fuel gauge typically has 5 to 6 segments. It is advisable to refuel when there are only 2 segments left to avoid running out of fuel midway. During actual refueling, the amount of fuel may exceed the marked capacity. This is because the fuel tank capacity specified by the manufacturer is measured from the bottom of the tank to the safety limit. There is additional space from the safety limit to the tank opening, which is designed to allow for fuel expansion due to temperature increases without causing overflow. If fuel is filled up to the tank opening during refueling, the actual amount of fuel added may exceed the marked capacity. Vehicle fuel consumption is directly influenced by five main factors: driving habits, the vehicle itself, road conditions, natural wind, and environmental temperature. Specific factors that increase fuel consumption include: Driving habits: Aggressive driving, such as sudden acceleration, frequent overtaking, and not easing off the throttle before stopping at a red light, can increase fuel consumption. The vehicle itself: Vehicles with larger engine displacements generally consume more fuel than those with smaller displacements because larger displacements typically produce more power, requiring more fuel to burn. Heavier vehicles also consume more fuel due to the need for greater driving torque. Road conditions: Driving on unpaved roads, muddy roads, soft surfaces, or mountainous terrain increases resistance and fuel consumption. Natural wind: Driving against the wind or on windy days increases vehicle resistance and fuel consumption. Low environmental temperatures: Cold engine temperatures make it harder for fuel to atomize during cold starts, requiring more fuel for combustion. Additionally, the engine's computer may control higher idle speeds to warm up the engine, further increasing fuel consumption.
Was this review help?
15
5
Share
LeIsabela
09/13/25 3:24am
I've been driving a GLC260L for a while now, and its fuel tank holds around 66 liters. That's actually pretty spacious for a midsize SUV like this one—I can easily cover long road trips without constantly pulling over for gas. For example, on highway drives, a full tank gives me roughly 650-700 kilometers of range, which is perfect when I'm exploring new spots with friends. I also pay attention to fuel efficiency tips, like keeping tires properly inflated to extend mileage. If you're considering this model, know that the design balances capacity with everyday practicality, so it doesn't feel bulky in urban areas where refueling is quick. Regular upkeep, like checking for leaks, keeps things humming along nicely.
Was this review help?
12
0
Share
Expand All
More Forum Discussions

What displacement is equivalent to a 1.3t engine?

A 1.3t engine is essentially a 1.3L naturally aspirated engine equipped with a turbocharger to enhance its power output and torque. Therefore, the actual displacement remains 1.3L, but in terms of power, a 1.3t engine is comparable to a 1.8L naturally aspirated engine. Different manufacturers have varying engine tuning approaches, but generally, a turbocharged engine of the same displacement delivers about 40% more power than a naturally aspirated one. In Western countries, the displacement of a turbocharged engine is often calculated by multiplying its actual displacement by 1.4. However, in China, only the direct numerical value is considered—both 1.3t and 1.3L engines are taxed based on the 1.3L displacement for vehicle purchase. Turbocharging not only provides stronger power than natural aspiration but also improves fuel efficiency, which is why many automakers have introduced small-displacement turbocharged engines. Generally, a larger displacement results in higher power output, but it also leads to higher fuel consumption. This is why off-road vehicles and sports cars typically have larger displacements. Smaller-displacement cars, on the other hand, offer more modest performance but better fuel economy. However, even with a small displacement, proper turbocharger tuning can enable these engines to outperform larger naturally aspirated engines in terms of power output.
8
4
Share

How to Adjust a Sagging Car Door by Yourself?

Here are the methods to adjust a sagging car door by yourself: 1. The entire door is offset downward: When this problem occurs, you need to loosen the hinge screws on the body side and raise the installation position of the hinges, which will lift the entire door upward. 2. The rear end of the door drops: When this problem occurs, loosen the hinge screws on the body side, then move the hinges backward, and finally move the lower hinge backward. Adjusting the hinges requires certain skills and experience, so it is not recommended for car owners to perform the repair themselves. It is best to go to a professional repair shop for inspection and repair.
5
1
Share

What needs to be repaired when a diesel engine overheats?

If the cylinder head gasket is damaged, directly replace the cylinder head gasket and resurface the cylinder head; replace the engine oil and thermostat. Below is an introduction to the related content: 1. Engine overheating: Thermal expansion and contraction cause the cylinder block space to shrink, leading to cylinder block wear, piston ring breakage. If the piston seizes and causes cylinder seizure, it will result in piston connecting rod deformation and throttle damage. 2. Cylinder head gasket damage: Causes damage to the cylinder head gasket (the gasket between the engine block and cylinder head), resulting in mixing of coolant and oil passages, thereby damaging the radiator and catalytic converter, and potentially causing cylinder head deformation. It may also damage the thermostat valve and temperature sensor.
15
1
Share

How to Repair a Small Scratch on the Car Paint?

This type of scratch can be completely removed through polishing. Here are the relevant details: 1. Smooth and glossy paint surface: Polishing utilizes the physical method of cutting, combined with abrasive compounds as the medium, to remove unevenness on the paint surface, thereby achieving a smooth and glossy finish. 2. Polishing: Polishing is a process that removes surface irregularities from the paint. To achieve a more even surface, a portion of the paint is removed, allowing the paint to reflect light at greater angles, making it appear shinier and brighter. Avoid frequent waxing, especially polishing. The number of times a car is polished should not exceed five, and waxing should also be done in moderation.
15
4
Share

What is the equivalent displacement of a 1.2T engine?

1.2T is equivalent to the horsepower output of a 1.6 to 1.8-liter naturally aspirated engine. A 1.2T engine is essentially a 1.2-liter naturally aspirated engine equipped with a turbocharger to enhance its power and torque output. The 'T' primarily increases the power while the displacement remains unchanged at 1.2 liters. A 1.2T engine typically produces around 200 Nm of torque, which can reach the level of a 2.0-liter engine. Similarly, a 1.0T engine still has a displacement of only 1.0 liters and does not increase the actual engine displacement due to turbocharging. Under the same displacement, a 1.0T engine delivers more robust power output compared to a 1.0-liter naturally aspirated engine and can also achieve better fuel efficiency to some extent. Taking Volkswagen's 1.2T as an example, the 1.2TSI engine not only features direct fuel injection technology but also benefits from its four-cylinder structure. While three-cylinder engines are more common in this displacement range, Volkswagen's four-cylinder design avoids issues like idle vibration and excessive noise associated with three-cylinder engines.
6
3
Share

Is a diesel engine oil pressure of 6 bars normal?

Diesel engine oil pressure of six bars is considered high. Below is an introduction to diesel generator-related content: 1. Diesel Engine: A diesel engine is an engine that burns diesel fuel to release energy. Compared to gasoline engines, the biggest advantages of diesel engines are their high torque and good fuel efficiency. Diesel engines and gasoline engines share many similarities in their working processes. 2. Working Process: During operation, the engine goes through four strokes: intake, compression, power, and exhaust. However, diesel engines use diesel fuel, which has higher viscosity compared to gasoline and is less prone to evaporation. Diesel also has a lower auto-ignition temperature than gasoline. 3. Compression Ignition: The formation of the combustible mixture and the ignition method in diesel engines are fundamentally different from those in gasoline engines. Notably, the mixture in diesel engine cylinders is ignited by compression rather than by a spark. During operation, only air enters the cylinders of a diesel engine.
20
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.