What is the fuel tank capacity of the Fengxing Lingzhi?

2 Answers
DeCora
07/29/25 8:33am
Currently, there are 8 models of the Dongfeng Fengxing Jingyi X5, among which the 1.5T version has a fuel tank capacity of 55 liters, while other versions have a fuel tank capacity of 45 liters. This data is released by the automobile manufacturer, and owners who have purchased the Dongfeng Fengxing Jingyi X5 can also check it on the vehicle's configuration sheet. The fuel grade for the Dongfeng Fengxing Jingyi X5 is 92, with a fuel consumption of 6.7 to 7.4L per 100 kilometers. A full tank of fuel can cover a distance of 672 to 743 kilometers. During daily driving, it is necessary to always pay attention to the remaining fuel in the tank. Generally, this is observed through the fuel gauge inside the vehicle. If there are no other issues, the fuel level will be accurately reflected on the gauge. The fuel gauge on the dashboard usually has 5 to 6 segments. When there are only 2 segments left, it is advisable to refuel to avoid running out of fuel midway. During the actual refueling process, the amount of fuel may exceed the marked capacity. This is because the fuel tank capacity marked by the automobile manufacturer is the volume from the bottom of the tank to the safe limit, and there is still some space from the safe limit to the tank opening. This space is reserved to ensure that the fuel inside the tank can expand when the temperature rises without overflowing the safe space of the tank. If the fuel is filled up to the tank opening during refueling, the actual refueling amount may exceed the marked fuel tank capacity.
Was this review help?
8
5
Share
RyderLee
08/11/25 6:04pm
When driving my Lingzhi on long trips, I paid special attention to the fuel tank. The car's tank holds about 52 liters when full, which matches the official 52L capacity. On highways, it can run about 600 kilometers, while in city traffic with congestion, it lasts around 400 kilometers before needing a refill. Here’s a key fueling tip: plan to refuel when the gauge shows a quarter left—never wait until the warning light comes on, as it can damage the fuel pump. Once at a gas station, I saw an experienced driver who insisted on waiting until the tank was nearly empty to refuel, only to end up spending over 2,000 yuan on a major fuel pump repair due to overheating. Also, avoid filling the tank completely in summer, as heat expansion can cause fuel to overflow through the vent, which is both dangerous and wasteful.
Was this review help?
16
4
Share
Expand All
More Forum Discussions

How to Remove the Door Panel of a Mercedes-Benz S350?

When removing the door panel of a Mercedes-Benz S350, it is best to go to a repair shop or a 4S store and ask a professional to operate it to prevent yourself from disrupting the wiring inside the door panel, which may affect the normal use of the car. The door panel removal process is quite troublesome. The specific method is as follows: 1. Pry off the small cover on the door handle and remove the screw inside. 2. Pry off the cover of the window lifter and unplug the wiring connector inside. 3. Remove the screw at the position of the window lifter. 4. After removing the window lifter screw, use a screwdriver to pry open the panel of the door handle from top to bottom. 5. Remove all the plastic clips inside the door handle panel, then lift the entire panel upwards, and the door panel of the Mercedes-Benz S350 can be removed.
11
1
Share

What is the correct method for shifting gears in a manual transmission car?

Manual transmission car shifting the correct method is: 1, start with first gear, after driving a few meters then shift to second gear; 2, when the speed reaches above 20 mph, below 35 mph shift to third gear; 3, speed reaches above 35 mph, below 45 mph shift to fourth gear; 4, speed reaches above 45 mph shift to fifth gear. Extended content: When shifting gears, the clutch and throttle must be well coordinated. Press the clutch pedal all the way down, then release the throttle pedal, and quickly shift to the corresponding gear. After shifting, immediately release your hand and do not keep it on the gear lever for a long time, as this can easily damage the gear lever. Shift gears completely and accurately. Sometimes driving may involve casual shifting, lifting the clutch before the gear is fully engaged, which can cause significant damage to the transmission.
4
1
Share

Where is the sunroof drain pipe of the Bora located?

The Bora's sunroof has four drainage outlets, one at each of the front, rear, top, and bottom. The two rear drainage outlets are the easiest to find, located under the chassis near the rear wheels, one at the top and one at the bottom. The front drainage outlets are inside the A-pillars on both sides, where water usually drips directly into the gaps of the car and flows out. The purpose of the sunroof drain pipe is to prevent water accumulation on the roof and to facilitate drainage. The maintenance precautions for the car sunroof are as follows: 1. If the car sunroof is not properly maintained, it can easily lead to clogged drainage outlets. Once the sunroof drainage outlets are blocked, the car will leak during rainy days. 2. If the vehicle is parked for a long time, it is best to thoroughly clean the sunroof once with talcum powder to prevent the rubber seals from undergoing chemical reactions in the air and aging naturally. 3. Pay attention to the sunroof's rubber seals to see if they show signs of aging or poor sealing. If there are issues with the seals, they can only be replaced.
8
0
Share

How to Adjust the Front and Rear Position of the Front Passenger Seat in the Sylphy?

Here are the steps to adjust the front and rear position of the front passenger seat in the Sylphy: 1. There is a horizontal lever under the seat. Lift it up to move the seat forward or backward, and release it once the desired position is reached. 2. The Nissan Sylphy's seat adjustment is manual, allowing for adjustments to the seat's front and rear position, tilt angle, and height. It is not as convenient as an electric seat. Here is an introduction to the Sylphy model: 1. The Sylphy and Teana adopt a new family design language, transforming from their previous moderate and stable image into a stylish and attractive appearance. 2. The rear of the Sylphy features rich lines and sharp angles, with larger tail lights on both sides and a black decorative panel added to the lower bumper, making it more dynamic. 3. For the interior, the Sylphy adopts a new design with a layout rich in lines and layers. 4. The new-generation Sylphy is still equipped with the HR16 engine, with a maximum output power of 102kW and a maximum torque of 169N•m, paired with a CVT transmission.
20
5
Share

What are the symptoms of a bad car cylinder head gasket?

The following are the fault manifestations after the cylinder head gasket is blown: 1. If the engine cylinder communicates with the cooling water jacket or lubricating oil passage, yellow-black oil foam will float on the upper surface of the coolant in the radiator, or there will be obvious water in the oil pan. When these two types of gas channeling are severe, the exhaust will contain water or engine oil. 2. High-pressure gas in the gas-oil passage enters the lubricating oil passage connected between the engine block and the cylinder head. The oil temperature in the oil pan remains high during engine operation, the oil viscosity becomes thin, the pressure decreases, and the oil deteriorates quickly. The oil sent to the upper part of the cylinder head to lubricate the valve train obviously contains bubbles. 3. Gas channeling between two adjacent cylinders: Without opening the decompression, when turning the crankshaft, it can be felt that the pressure in both cylinders is insufficient. When starting the engine, there is a phenomenon of black smoke emission, the engine speed drops significantly, and the power output is insufficient.
18
2
Share

Difference Between AT and Tiptronic Transmission?

Tiptronic transmission is the most common type of transmission, which allows both manual and automatic gear shifting, with the ability to switch between the two modes freely. AT (Automatic Transmission) is a type of automatic transmission that can automatically shift gears up and down. Below are the specific differences between Tiptronic and AT transmissions: 1. Manual Transmission, also known as MT, is commonly referred to as a stepped transmission. This is because the transmission has fixed gear ratios, such as a first gear ratio of 3.455, second gear of 2.056, up to fifth gear of 0.85. These numbers multiplied by the final drive ratio give the total gear ratio. A manual transmission consists of an output shaft, input shaft, and countershaft. Although Tiptronic can enhance driving pleasure, it does not offer full manual control, and the manual mode is often underutilized. Additionally, using the manual mode can be less fuel-efficient. 2. AT transmission is a type of automatic transmission, commonly found in American cars. The reason AT transmissions can shift gears freely is that they use vehicle speed and load as parameters for control. The biggest advantage of AT transmissions is their ability to directly shift gears based on vehicle speed, with quick shifting and minimal noticeable jerkiness during gear changes. However, AT transmissions have a complex internal structure, leading to higher maintenance and repair costs in the long run.
13
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.