What is the fuel tank capacity of the BMW X7 in liters?

1 Answers
DelElliott
07/30/25 6:02am
2022 BMW X7 offers a total of 6 models, all with a fuel tank capacity of 83 liters. The vehicles are equipped with either a 3.0-liter or a 4.4-liter turbocharged engine, and all models feature an 8-speed automatic transmission (AT). All models adopt a front-engine, four-wheel-drive layout. Among vehicles in the same class, the 2022 Range Rover Sport 3.0 L6 SE has a fuel tank capacity of 104.3 liters, while the 2022 BMW X5 M has a fuel tank capacity of 83 liters. During actual refueling, the amount of fuel may exceed the calibrated capacity. This is because the fuel tank capacity specified by the automaker is measured from the bottom of the tank to the safety limit level. There is additional space from the safety limit level to the tank opening, which is designed to accommodate fuel expansion due to temperature increases without causing overflow. If fuel is filled up to the tank opening during refueling, the actual fuel quantity may exceed the calibrated tank capacity. To check the remaining fuel level, owners can observe the fuel gauge on the right side of the instrument panel, marked with E (Empty) and F (Full). When the needle is close to E, it indicates low fuel, while proximity to F signifies sufficient fuel.
Was this review help?
14
3
Share
More Forum Discussions

What are the steps for disassembling and assembling a Jetta engine?

Remove the fuel pump fuse, start the engine to release fuel pressure, and disconnect the negative battery cable. Disassemble the intake pipe assembly, remove the upper intake manifold assembly, and take off the lower intake manifold assembly to prevent debris from entering the passages. Remove the heated oxygen sensor, detach the exhaust pipe and gasket from the mounting bracket, and clean the exhaust manifold sealing surface to check for holes, damage, or cracks. Remove the protective plate to expose the generator belt, take off the belt, remove the engine crankshaft output pulley, and detach the triangular fixed bracket on the engine side. Loosen the cylinder head cover bolts in a diagonal sequence, remove the cylinder head cover, take off the valve cover gasket (ensuring its integrity), and then remove the cylinder head.
7
5
Share

What are the steps to remove the dashboard of a Volkswagen Polo?

Pry off the black trim frame around the head unit, being careful not to use excessive force to avoid breaking the frame. Remove the fixing screws around the head unit, taking care not to drop the screws into the gaps of the center console. Disconnect the wiring harness at the back. Connect the wiring harness of the head unit to the new head unit. These are specialized connectors, so there's no need to worry about incorrect connections. After installing the new head unit, power it on for testing. Once the test is successful, tighten the screws to secure it, and finally reattach the black trim frame.
15
5
Share

How to Remove and Replace a Seat Belt Buckle?

First, adjust the seat and remove the four fixing bolts on the front and back of the seat. Locate the wiring of the car seat and disconnect the sensor wire of the seat belt buckle. Remove the seat cushion, take off the seat airbag, then remove the bolt fixing the seat belt, and finally take out the seat belt buckle slot. Remove the sensor inside the seat cushion, install the new seat belt buckle slot onto the seat, connect the wiring, and tighten the bolts. Install the weight sensor and the new retractor onto the seat, and tighten them with a wrench.
20
3
Share

What is the method to reset the maintenance light on a Mercedes-Benz W221?

Turn the ignition switch to the first position. Simultaneously press and hold the 'OK' button (S110s6) on the multifunction steering wheel and the 'Answer/End' button on the right side for about 5 seconds. Select 'ASSYSTPlus workshop' and confirm by pressing the 'OK' button (S110s6). Use the 'Forward/Backward' button (S110s1) to select 'Service Performed' and confirm by pressing the 'OK' button (S110s6). Choose 'Complete (Full) Service' or 'Individual'.
6
1
Share

How to Repair Gear Slippage in a Tiller?

Gears only partially engage in width, the locking steel ball does not snap into the locking groove of the shift rail, or the shift lever end is severely worn. When the axial force on the gear exceeds the locking force generated by the locking spring, the sliding gear is pushed away, resulting in automatic gear disengagement. If the shift fork is deformed or severely worn, and the centerline of the sliding gear intersects at an angle with the shaft centerline, the sliding gear may move axially and disengage. Severe wear of the steel ball or positioning groove can also make it difficult to position the sliding gear during transmission, leading to gear disengagement. Bearing wear increases the clearance, causing a skewed thrust during gear engagement, which results in gear disengagement.
2
2
Share

How to Install the Intake Camshaft on BMW N46 Engine?

Before installing the camshaft, first install all bearing caps and check if the camshaft holes are misaligned. When installing the camshaft, the cam of cylinder 1 must face upwards without pressing the valves. First, tighten the bearing caps of the 2nd and 5th positions alternately in a diagonal pattern with a torque of 20 Nm, then install the bearing caps of the 1st and 3rd positions, and finally install the bearing cap of the 4th position. Install the camshaft half-moon key and timing gear, tighten the bolts to prevent camshaft sliding and reduce risks, with a torque of 80 Nm.
2
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.