What is the fuel tank capacity of the BJ40 in liters?

1 Answers
StephanieAnn
07/29/25 8:04pm
BJ40 has a fuel tank capacity of 75 liters, as officially announced. For the BJ40 2022 2.0T automatic four-wheel-drive official edition and the automatic four-wheel-drive Ring Tower Champion edition, the recommended fuel grade is 92 octane, with a fuel consumption of 9.9L per 100 kilometers. A full tank can cover a distance of approximately 757km. The BJ40 2022 2.3T automatic four-wheel-drive Excellence edition requires 95 octane fuel, with a fuel consumption of 11.5L per 100 kilometers, allowing a range of about 652km on a full tank. During daily driving, it is essential to monitor the remaining fuel level in the tank. This is typically done by observing the fuel gauge inside the vehicle. Under normal circumstances, the fuel gauge accurately reflects the fuel level. The fuel gauge usually has 5 to 6 segments, and it is advisable to refuel when only 2 segments remain to avoid running out of fuel mid-journey. In actual refueling, the amount of fuel added may exceed the marked capacity. This is because the fuel tank capacity specified by the manufacturer is measured from the bottom of the tank to the safety limit, leaving some space from the safety limit to the tank opening. This space ensures that the fuel can expand when temperatures rise without overflowing. If fuel is filled up to the tank opening during refueling, the actual amount of fuel added may exceed the marked capacity.
Was this review help?
9
4
Share
More Forum Discussions

What does 'Inspection valid until July 2021' mean?

For exempted vehicles, no endorsement will be made on the supplementary page of the vehicle license. This is the annual inspection mark. Relevant information is as follows: 1. Inspection content: National regulations stipulate that motor vehicles must regularly pass exhaust emission tests, vehicle appearance, lights, brakes, chassis inspections, etc., and obtain an inspection compliance mark without any traffic violation records. All annual inspection dates are based on the registration date on the vehicle license. Motor vehicles must undergo safety technical inspections according to the following periods from the date of registration, commonly referred to as 'annual inspection' or 'annual review'. 2. Inspection frequency: Small and micro non-operating passenger vehicles within 6 years are inspected every 2 years, those over 6 years are inspected annually, and those over 15 years are inspected every 6 months.
17
2
Share

What level does the Nexen SH9i tire belong to?

Nexen SH9i tires offer excellent support performance, braking performance, and drainage performance, providing comprehensive assurance for safe driving. Below is relevant information about the tires: 1. Tire functions: Mainly include dry grip, hydroplaning resistance, comfort provision, noise reduction, impact resistance, wet grip, load-bearing capacity, handling ability, average wear, and mileage. 2. Tire cross-section structure: Generally divided into four parts: tread, shoulder, sidewall, and bead. Each part has its own function. The tread mainly contacts the ground, the shoulder and sidewall provide support, and the bead seals with the rim. 3. Internal composition of tires: The tire interior consists of multiple layers of different materials, including tread pattern, overlay, steel belt, stress absorption rubber strip, carcass ply layer, and inner liner.
8
1
Share

What Causes the Abnormal Noise When Coilover Suspension Goes Over Uneven Roads?

This is a normal phenomenon caused by overly stiff springs. Other abnormal causes are as follows: 1. Interference between components: Due to impacts or the installation of additional equipment, two components may affect each other. Solution: Only reshaping, repairing, or replacing the relevant components can eliminate the interference. 2. Loose bolts or nuts: Long-term driving on poor road conditions can naturally loosen bolts; improper disassembly or installation can damage bolts; insufficient tightening torque or incorrect bolt specifications. Solution: Tighten or replace the bolts and nuts. 3. Driveshaft universal joint failure: Caused by a broken dust cover or oil leakage that was not repaired in time. Solution: Replace the driveshaft universal joint with a new one. When the car is stationary, the ground clearance at the four corners of the body has a significant impact on the load of the wheels at those positions.
2
2
Share

What is the trunk capacity of the Song Plus DM-i?

The maximum trunk storage space is 574L. Below are the specific details of the BYD Song Plus DM-i: 1. Exterior: The front fascia features a large-sized grille paired with silver chrome trim. As for the side profile, it adopts flowing line designs, giving the overall shape a dynamic and fashionable appearance. 2. Powertrain: The BYD Song Plus DM-i is equipped with a dedicated 1.5L Xiaoyun plug-in hybrid engine, delivering a maximum power of 110 horsepower and a maximum torque of 135 Nm. It comes with blade battery technology, offering pure electric range options of either 51km or 110km.
10
5
Share

Where is the Outlander's Cabin Air Filter Located?

Outlander's cabin air filter is located inside the glove compartment on the passenger side. The functions of the cabin air filter are: 1. It ensures the filter fits tightly against the housing, preventing unfiltered air from entering the cabin; 2. It separates solid impurities such as dust, pollen, and grinding particles from the air; 3. It adsorbs moisture, soot, ozone, odors, carbon oxides, SO2, and CO2 from the air; 4. It maintains clean air in the passenger compartment, preventing bacterial growth and creating a healthy environment; 5. It effectively separates solid impurities such as dust, core powder, and grinding particles from the air; 6. It effectively blocks pollen, ensuring that drivers and passengers do not suffer allergic reactions that could affect driving safety.
1
4
Share

What Type of Battery Does a Car Key Use?

Car keys typically use the following types of batteries: 1. CR2016 coin cell battery; 2. CR2025 coin cell battery; 3. Alkaline 12V battery. The steps to replace a car key battery are: 1. Remove the mechanical key; 2. Insert a flat-head screwdriver into the OPEN slot at the bottom and gently pry up and down; 3. Once a gap appears, use the screwdriver to carefully pry open the key along the gap; 4. Remove the old battery and replace it with a new one; 5. Reassemble the key. The working principle of a car key is: it emits a weak radio wave from the owner, which is received by the car's antenna. The electronic control unit then identifies the signal code, and the system's actuator performs the locking or unlocking action.
12
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.