What is the fuel tank capacity of the 2020 Honda Avancier?

1 Answers
MariaDella
07/29/25 10:00pm
2020 Honda Avancier has a fuel tank capacity of 57 liters, and the recommended gasoline specification is 92# or above unleaded gasoline. The Avancier is a mid-size SUV under GAC Honda. Both the 2017 and 2019 models have a fuel tank capacity of 57 liters, with the same gasoline specification of 92# or above unleaded gasoline. If the owner wants to know the remaining fuel level, they can observe the fuel gauge on the right side of the dashboard, which is marked with E and F. When the pointer is close to E, it means the fuel is running low, and when it is close to F, it indicates sufficient fuel. The maintenance of the fuel tank is as follows: Drain the accumulated water and sediment in the fuel tank, and check for any oil leakage at the fuel pipe joints and switches. For the fuel tank cap equipped with air and vapor valves, also check whether the vent holes are clear. The filter screen at the fuel filler inlet should be kept intact to prevent impurities from entering the fuel tank during refueling and clogging the fuel lines. The sealing gasket of the fuel filler cap should also be intact to prevent fuel from overflowing during driving.
Was this review help?
17
1
Share
More Forum Discussions

Are There Any Disadvantages to Replacing the Windshield?

Replacing the windshield has disadvantages, such as increased wind noise while driving. Methods for maintaining the car windshield include: 1. Use specialized or suitable wiper blades and replace them promptly; 2. Keep the windshield clean; 3. Use automotive-specific glass cleaner. Precautions for windshield replacement are: 1. To prevent air or water leaks, avoid washing the car for three days, and remove the tape securing the windshield after three days; 2. Drive smoothly, avoiding sudden braking and rapid acceleration; 3. Try to avoid driving on excessively bumpy roads to prevent windshield displacement; 4. Keep the maximum speed below 80 km/h and avoid highway driving; 5. After replacing the rear windshield, do not open windows while driving for the first three days to prevent displacement due to wind pressure; 6. Do not insert parking permits or other cards into the gap between the windshield and the dashboard.
2
0
Share

What are the causes of difficult cold starts in engines?

The causes of difficult cold starts in engines are: 1. Air leaks in the intake system; 2. Fuel pressure is too low; 3. Clogged air filter; 4. Faulty coolant temperature sensor; 5. Faulty mass airflow sensor; 6. Malfunctioning idle control valve or auxiliary air valve; 7. Cold start injector not working; 8. Fuel injector leakage; 9. Incorrect ignition timing; 10. Broken wiring from the starter switch to the ECU; 11. Cylinder compression pressure is too low. Methods to address starting difficulties include: 1. Check the battery condition; 2. Use suitable engine oil; 3. Replace spark plugs promptly. Methods for warming up the engine: 1. Drive after 30 seconds to 1 minute of idling; 2. Maintain low-speed driving; 3. Once the engine reaches normal operating temperature, drive as usual.
4
2
Share

How to Drive in a Straight Line?

The method to drive in a straight line is: 1. Hold the steering wheel steadily and straight while driving, avoiding large turns; 2. Find suitable reference points on the road and focus your gaze ahead. Precautions for novice drivers include: 1. Adjust the seat position and rearview mirrors before driving, and fasten the seatbelt; 2. Turn the ignition key and wait for the computer self-check to complete before starting; 3. Ensure the handbrake is released before driving; 4. Keep your heel on the floor when pressing the pedals, slowly release the clutch and gently press the accelerator when starting; 5. Always use turn signals and reduce speed when turning or changing lanes; 6. When driving on clear roads, look straight ahead at a distance of 100 meters, not just at the immediate front of the car; 7. Use hazard lights when parking by the roadside; 8. Engage the handbrake when parked; 9. Stay focused while driving; 10. Avoid occupying two lanes for extended periods.
4
2
Share

What is the difference between fully synthetic and semi-synthetic engine oil?

The differences between fully synthetic and semi-synthetic engine oils are: 1. Different base oils: Fully synthetic oil is a mixture of Group III, IV, and V base oils; semi-synthetic oil uses Group III base oil. 2. Different replacement intervals: Fully synthetic oil should be replaced once a year or every 10,000 kilometers during use; semi-synthetic oil should be replaced every six months or every 7,500 kilometers during use. Engine oil, also known as engine lubricant, serves the following functions: 1. Cooling and temperature reduction; 2. Sealing and leak prevention; 3. Cleaning and purification; 4. Shock absorption and buffering; 5. Lubrication to reduce wear; 6. Rust and corrosion prevention; 7. Component protection.
17
0
Share

What transmission does the Changan Eado use?

The Changan Eado uses a 7-speed dual-clutch transmission. The Changan Eado is a compact 4-door 5-seater sedan with body dimensions of 4730mm in length, 1820mm in width, and 1505mm in height, with a wheelbase of 2700mm and a fuel tank capacity of 53 liters. It is equipped with a 1.4T turbocharged engine, delivering a maximum power of 116 kW at 5500 rpm and a peak torque of 260 Nm between 1500 to 4000 rpm. The drivetrain is front-wheel drive, featuring MacPherson strut front suspension and a torsion beam rear suspension.
12
3
Share

What Causes the Plastic Friction Sound When Turning the Steering Wheel?

The reasons for the plastic friction sound when turning the steering wheel are: 1. Friction between plastic components; 2. Issues with the steering wheel airbag clock spring; 3. Aging of the steering tie rod ball joint; 4. Loose or damaged stabilizer bar; 5. Problems with the shock absorber thrust bearing; 6. Improper tension or aging of the power steering belt. The solutions for the plastic friction sound when turning the steering wheel are: 1. Apply some grease to the steering wheel airbag clock spring or replace it; 2. Replace the steering tie rod ball joint; 3. Add shims to the stabilizer bar or replace it; 4. Apply grease to the shock absorber thrust bearing or replace the part; 5. Adjust the belt tension or replace the belt.
17
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.