What is the fuel consumption per 100 kilometers for the Hongqi HS5?

2 Answers
JosephineLee
08/27/25 6:00am
The fuel consumption per 100 kilometers for the Hongqi HS5 is 10.5 liters. Relevant information is as follows: 1. Suspension: The front suspension of the Hongqi HS5 uses a MacPherson independent suspension, while the rear suspension uses a multi-link independent suspension. The multi-link independent suspension can improve the tire's ground contact performance, thereby enhancing the tire's grip. With improved grip, the vehicle's handling also improves. The MacPherson suspension is a relatively common type of independent suspension and is also the most widely used independent suspension. The structure of the MacPherson suspension is simple, consisting of only one L-shaped control arm. 2. Drive: The Hongqi HS5 has both front-wheel-drive and four-wheel-drive versions. The four-wheel-drive version is equipped with an on-demand four-wheel-drive system and uses a multi-plate clutch central differential. Vehicles equipped with an on-demand four-wheel-drive system are not in four-wheel drive all the time; they mostly operate in two-wheel drive during normal conditions and only switch to four-wheel drive when encountering special road conditions.
Was this review help?
11
3
Share
VonJuliette
09/09/25 4:53am
I've been driving the Hongqi HS5 for almost two years now, with an average fuel consumption fluctuating between 9 to 10L/100km. In city traffic jams, it can go up to 12L, while on the highway at a steady speed of around 80 km/h, it drops to about 7L. I usually drive quite aggressively, but maintaining smooth acceleration and avoiding speeding can save some fuel. Actual fuel consumption depends on road conditions and personal driving habits. I recommend using a mobile app to record each refueling for more accurate tracking. Using air conditioning in summer increases fuel consumption, and cold starts in winter also raise it slightly. Regularly maintaining tire pressure at the standard value of 2.5 bar is crucial. Don't underestimate these details—they can add up to significant fuel savings over time.
Was this review help?
3
1
Share
Expand All
More Forum Discussions

Where is the U-turn marking located at an intersection?

U-turn markings at intersections are indicated within the lane lines. Below are relevant details: Regulations: Article 49 of the "Regulations for the Implementation of the Road Traffic Safety Law of the People's Republic of China" states that motor vehicles are not allowed to make U-turns at locations with no U-turn or no left-turn signs and markings, as well as at railway crossings, pedestrian crossings, bridges, sharp curves, steep slopes, tunnels, or sections prone to danger. Motor vehicles can make U-turns at locations without prohibitive U-turn or left-turn signs and markings, but must not hinder the passage of other normally traveling vehicles and pedestrians. Intersection markings: Intersection markings are primarily painted on the road surface, enduring exposure to sun, rain, snow, ice, and the impact and wear from vehicles, thus requiring strict performance standards.
13
3
Share

Does the 4S store handle the second-year renewal insurance?

The "Compulsory Traffic Accident Liability Insurance for Motor Vehicles" has corresponding regulations: The insurance policy of the compulsory insurance for the previous year of the insured motor vehicle should be provided. When signing the compulsory insurance contract, the policyholder shall not require the insurer to attach any conditions other than the insurance clauses and premium rates. During the validity period of the insurance contract, if the insured motor vehicle increases the risk due to modification, installation, change of use, etc., the insured shall promptly notify the insurer. You can continue to purchase car insurance at the 4S store, or you can buy car insurance yourself from an insurance company. Buying it yourself from an insurance company can enjoy more discounts. It is best to find the largest local insurance company for guaranteed service.
6
5
Share

What are the application guidelines for Volkswagen Lavida car lights?

Here is an introduction to the application guidelines for Volkswagen Lavida car lights: Position lights: Turn the light control switch on the left side of the steering wheel forward one notch to turn on the position lights. Low beam: Turn the light control switch inward twice to turn on the low beam. High beam: Push the light control switch forward once to turn on the high beam. Turn signals: Lift the light control switch forward and upward once for the right turn signal; lift the light control switch forward and downward once for the left turn signal. Fog lights and hazard warning lights: There are two light control switches between the instrument panel and the co-driver's panel. Turn them on to activate the fog lights and hazard warning lights (double flash).
3
1
Share

What are the methods for testing a car battery?

Currently, most car batteries on the market are tested using a battery tester to measure the battery's voltage. Typically, the no-load voltage of a battery is around 13 volts, and the full-load voltage should not be less than 12 volts. Additionally, observe whether there is obvious swelling or bulging on both sides of the battery. If white or green powdery substances appear around the battery terminals, it indicates a performance issue with the battery. To determine if the electrolyte has deteriorated or lost water, charge the battery for 3 to 6 hours, then touch the side of each battery cell's casing by hand. If the battery feels hot to the touch, it means that cell has failed. Another method is to open the cover on top of the battery, where you can clearly see six round holes beneath it. Carefully inspect the color of the electrolyte in each hole. If the electrolyte has turned black, it indicates that the lead powder from the plates has fallen off, meaning that cell has failed.
19
4
Share

What is the fit of h7/g6?

H7/g6 belongs to clearance fit. Clearance fit: Refers to a fit that has clearance (including when the minimum clearance equals zero). In this case, the tolerance zone of the hole is above the tolerance zone of the shaft, meaning the actual size of the hole is greater than or equal to the actual size of the shaft. The function of the clearance is to store lubricating oil, compensate for various errors, etc., and its size affects the degree of relative motion between the hole and the shaft. Clearance fit is mainly used for movable connections between holes and shafts, such as the connection between a sliding bearing and a shaft. Maximum clearance: The difference between the maximum limit size of the hole and the minimum limit size of the shaft, or the upper deviation of the hole minus the lower deviation of the shaft. Minimum clearance: The difference between the minimum limit size of the hole and the maximum limit size of the shaft, or the lower deviation of the hole minus the upper deviation of the shaft.
2
2
Share

What Causes a Scooter to Frequently Stall When Decelerating?

The reasons why a scooter frequently stalls when decelerating are as follows: Fuel system issues: Generally, it's a problem with the fuel system. There may be blockages or deposits, which can be resolved by cleaning. Short circuit: A point in the ignition circuit, possibly the kill switch or the ignition coil, may be damaged or burned out by current, causing the temperature to rise after working for a while, leading to a short circuit and poor spark plug ignition. Lean air-fuel mixture: It might be due to a lean air-fuel mixture in the carburetor. Adjusting the mixture slightly richer can help. Note that turning the adjustment screw outward enriches the mixture, while turning it inward leans it. Typically, it's adjusted by screwing it all the way in and then backing it out one and a half to two and a half turns. Avoid adjusting too much at once; a quarter to half a turn is appropriate. Test after each adjustment and fine-tune gradually.
18
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.