What is the fuel consumption per 100 kilometers for a 1.6L engine?

1 Answers
Eric
07/29/25 9:46pm
For a 1.6L displacement family sedan, a fuel consumption of around 8L per 100 kilometers is considered normal, while a consumption of approximately 7L per 100 kilometers is considered fuel-efficient. For a 1.8L displacement family sedan, a fuel consumption of around 9L per 100 kilometers is considered normal, while a consumption of approximately 8L per 100 kilometers is considered fuel-efficient. Below is an introduction to fuel consumption per 100 kilometers: 1. Theoretical calculation of fuel consumption per 100 kilometers: Generally, the fuel consumption per 100 kilometers provided by manufacturers is a theoretical value. It refers to the value measured by the dynamometer installed on the vehicle chassis under objective environmental conditions, converted into speed parameters, and then calculated at a specified speed to derive the theoretical experimental fuel consumption per 100 kilometers for the model. 2. Practical calculation of fuel consumption per 100 kilometers: In practice, the method to calculate fuel consumption per 100 kilometers is as follows: X/100=50/600, where X is the actual fuel consumption per 100 kilometers being calculated, 50 on the right side of the equation refers to 50L of fuel consumption, and 600 refers to the vehicle traveling 600 kilometers. Simply put, the vehicle consumes 50L of fuel over 600 kilometers. Solving the equation: X is approximately 8.33, so the actual fuel consumption per 100 kilometers for this vehicle is about 8.33L.
Was this review help?
1
2
Share
More Forum Discussions

How Many Liters of Antifreeze Does a Family Sedan Need

Family sedans generally require 4 to 6 liters of antifreeze, with the fluid level needing to be between the MAX and MIN lines. Methods for selecting antifreeze: The basic indicators of antifreeze are its freezing point and boiling point. In the market, antifreeze comes in several specifications with freezing points of -15°C, -25°C, -30°C, -40°C, etc. It is generally advisable to choose one that is at least 10°C lower than the lowest temperature in your region. Methods to determine if antifreeze is low: Observe the antifreeze warning light on the dashboard. If it lights up, it is likely due to low antifreeze levels, though it could also be caused by excessively high cylinder temperatures. Check the antifreeze reservoir. If the fluid level is below the minimum mark (MIN), do not continue driving and add antifreeze promptly. Check the water level scale markings on the antifreeze bottle. The antifreeze level should normally be between the maximum and minimum water level marks. Whether the antifreeze is low depends on the scale; if it is below the minimum water level, it indicates a shortage of antifreeze.
1
4
Share

What does the hazardous material vehicle type FL mean?

Hazardous material vehicle type FL generally refers to the items that tanker vehicles (typically hazardous material transport vehicles) are designed to carry. Documents from the State Council explicitly state that hazardous material transport vehicles must not change the type of cargo they transport. If the vehicle's designated cargo in the MIIT (Ministry of Industry and Information Technology) announcement is gasoline, it can only transport gasoline; if it's ethanol, it can only transport ethanol. Functions of tanker transport vehicles: Tanker specialized transport vehicles. For transporting hazardous chemicals in liquid form, such as flammable, explosive, or toxic substances, specialized tanker trucks are generally used. Common tank shapes include elliptical, square-round, and circular. Advantages of tanker transport vehicles: These vehicles are usually made of carbon steel with liners or stainless steel plates, equipped with multiple full-plastic anti-wave baffles inside. They undergo high-pressure airtightness tests, featuring high tank strength, stable center of gravity, and safe, smooth transport. They are also equipped with driving recorders and positioning systems. The vehicle body is sturdy and tightly sealed, with clear, standardized, and easily identifiable markings on the steel exterior.
17
5
Share

Which Should Be Released First: Handbrake or P Gear?

You should release the handbrake first before shifting out of P gear. For automatic transmission startup: Insert the key and ignite, first engage the handbrake, then shift gears. Additionally, vehicles with electronic handbrakes require the ECU to detect the brake pedal being pressed before releasing the handbrake. Otherwise, pressing the handbrake button will have no effect. For automatic transmission parking: First shift out of gear, then engage the handbrake, remove the key, exit the vehicle, and lock the door. Below is the startup sequence for automatic transmission: 1. Automatic transmission vehicles only have two pedals: the accelerator and the brake. The left pedal is the brake, and the right is the accelerator—this order must be clearly remembered. Before starting the car, first press the left brake pedal. 2. Insert the key and start the vehicle. 3. Check if the car's dashboard is functioning normally, look for any warning lights, and confirm that the fuel gauge shows sufficient fuel. 4. Press the brake with your right foot and release the handbrake with your right hand. 5. Shift the gear from P to D (note: keep your right foot on the brake at this time). 6. Release the brake, move your right foot to the accelerator pedal, and gently press to move forward.
5
0
Share

What Are the Effects of Not Applying Film to a New Car?

Not applying film to a new car will not have any significant impact on the vehicle, and it is perfectly fine to skip it if you prefer. Many car owners prioritize applying film as their first task after purchasing a new car. However, it is unnecessary to apply film on the front windshield, as this may impair nighttime driving visibility. In fact, the front windshield already has built-in UV protection, eliminating the need for additional film. Here are some key considerations when applying film: 1. Some meticulous car owners opt to apply a transparent protective film, commonly known as a "paint protection film" or "clear bra," to safeguard the car's paint. When applying such films, it is crucial to choose reputable brands and have them installed by professionals. Poor installation may result in bubbles or eventual peeling. 2. When applying film to the side windows of the driver and front passenger seats, it is advisable to leave two small openings to ensure clear visibility of the side mirrors. Additionally, avoid rolling the windows up or down immediately after applying film to the door windows, as this may cause the film to peel. Many car owners also opt for full-body color-changing films, which require registration with the local vehicle management office and updating the vehicle's registration photo. When selecting such films, always choose high-quality products to avoid damaging the car's paint.
6
1
Share

What happens if you refuel a car without turning off the engine?

When a car is not turned off, the operation of its instruments and equipment generates a significant amount of heat. This causes the gasoline inside the vehicle to evaporate more quickly, increasing the concentration of the fuel-air mixture near the fuel tank. Since this mixture is denser than air, it does not disperse easily. When the concentration of fuel vapor reaches a certain level, any spark produced by the running engine could potentially ignite and cause an explosion. Additionally, while the vehicle is running, the exhaust pipe continues to emit waste gases. Not only is the exhaust pipe extremely hot, but it may also emit sparks, which can pose a risk of igniting the gasoline. Below are some precautions to take when refueling: 1. At gas stations, smoking, making phone calls, refueling with the engine running, and slapping synthetic fiber clothing (which can generate static electricity) are all prohibited. 2. Smoking involves an open flame, so even if you remain in the car, you should extinguish any cigarettes. Phone calls can interfere with the electronic equipment at gas stations or generate electronic friction that may ignite fuel vapors. Besides open flames, gas stations are also wary of static electricity, which is most likely to be generated by synthetic fiber clothing. Therefore, avoid slapping your clothes while refueling.
17
2
Share

Will I be fined and penalized for driving at 131 km/h in a 120 km/h speed limit zone?

Driving at 131 km/h in a 120 km/h speed limit zone on highways generally does not result in penalty points or fines. Below is relevant information about driving at 131 km/h in a 120 km/h speed limit zone: 1. Reasons for no penalty points or fines: In most regions, as long as the speeding does not exceed 10% of the speed limit, there will be no penalty points or fines. Driving at 130 km/h means the speeding is less than 10%. In other words, in most areas, as long as you do not exceed 132 km/h, you will not be fined or penalized, but you will still receive a warning from the traffic police. 2. Handling of warning penalties: For "warning penalties," most regions currently do not allow online processing. You must bring your original ID card, driver's license, and vehicle registration certificate to the service window of the traffic police brigade or vehicle management office at the place of violation or where the vehicle is registered. If left unaddressed for a long time, it may affect the vehicle's annual inspection. Additionally, accumulating too many warnings may eventually lead to penalty points and fines.
13
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.