What is the fuel consumption of the Wrangler 2.0t?

1 Answers
DeclanMarie
07/29/25 10:43pm
The official fuel consumption of the Wrangler 2.0t is 9L/100KM, while the actual measured average fuel consumption is 12L/100KM, with a range of 10.6-13.44L. Relevant details are as follows: 1. The Wrangler 2.0t has a maximum horsepower of 266 and a maximum torque of 400 Nm, with an 8AT transmission across all models. The Wrangler 3.6 has a maximum horsepower of 284 and a maximum torque of 347 Nm, paired with a 5AT transmission. 2. The 2.0T engine has slightly less horsepower compared to the 3.6L engine, but the difference is not significant. Moreover, the 2.0T engine provides nearly 60 Nm more torque, making it more suitable for off-road vehicles that prioritize low-end torque.
Was this review help?
18
5
Share
More Forum Discussions

Will Replacing Low-Configuration Wheels with High-Configuration Ones Affect Annual Inspection?

Replacing low-configuration wheels with high-configuration ones generally will not pass the annual inspection. In practice, it depends on the strictness of the local vehicle management offices, so it is recommended to consult the local vehicle management office in advance. Typically, the wheels of low-configuration models are smaller than those of high-configuration models. Therefore, replacing low-configuration wheels with high-configuration ones is considered a vehicle modification. If the modified wheels are the same size as the original ones, they can pass the annual inspection. However, if the sizes are different, you will need to register the modification with the vehicle management office. Vehicle annual inspection refers to a mandatory test for all vehicles that have obtained official license plates and registration certificates, equivalent to an annual 'health check' for the vehicle based on the safety technical requirements for motor vehicle operation.
19
2
Share

What is the reason for the squeaking sound when the Baojun 730 drives on bumpy roads?

The reason for the squeaking sound when the Baojun 730 drives on bumpy roads is due to damaged buffer rubber in the chassis or loose ball joints in the chassis bracket. It is recommended to go to a maintenance station for inspection and repair. Taking the 2021 Baojun 730 1.5T manual fashion 7-seater as an example, this car is equipped with a 1.5T turbocharged engine and a 6-speed manual transmission, with a maximum power of 108kw, a maximum torque of 250nm, a maximum horsepower of 147ps, and a top speed of 170km/h. In terms of suspension, the front suspension type of this car is MacPherson independent suspension, the rear suspension type is torsion beam non-independent suspension, the body structure is unibody, and the power steering type is electric power.
2
4
Share

What transmission does the BMW 525 use?

BMW 525 uses an 8-speed automatic manual transmission. The transmission of an automatic manual vehicle is divided into two modes: automatic and manual. The 8-speed automatic manual transmission has 8 gears, and when the car is switched to manual mode, the 8th gear is the highest gear. The BMW 525 is a mid-to-large-sized car under the Brilliance BMW brand, with dimensions of 5106 mm in length, 1868 mm in width, and 1500 mm in height, and a wheelbase of 3105 mm. The BMW 525 is equipped with a 2.0T turbocharged engine, model B48B20C, with a maximum horsepower of 184 hp, a maximum power of 135 kW, and a maximum torque of 290 Nm. The maximum power speed ranges from 5000 to 6500 rpm, and the maximum torque speed ranges from 1350 to 4250 rpm.
20
5
Share

What is the plastic panel in front of the car called?

The plastic panel in front of the car is called a deflector. This plastic panel is usually fixed with screws or clips, and as long as it is not broken, there is no problem. Just tighten the screws. The function of the deflector is to reduce the lift generated when the car is driving at high speed. In addition to improving the car's exterior design, car designers tilt the entire body forward and downward to create downward pressure on the front wheels, and flatten the rear of the car to reduce the negative air pressure acting from the roof to the rear, preventing the rear wheels from lifting. They also install a downward-sloping connecting panel below the front bumper, which is integrated with the front skirt of the car body. A suitable air intake is designed in the middle to increase airflow and reduce the air pressure under the car.
19
3
Share

How to Use Quick-Drying Putty?

Pre-treatment: First, wet the sandpaper with water, then use the sandpaper to sand down dents and scratches, and finally wash away oil stains and dirt, allowing it to dry. Filling: You can use a small hard card or a small spatula to apply the putty, ensuring it is slightly higher than the surrounding area. After about an hour, use 400~1000 grit sandpaper with water to sand it smooth, completing the fine sanding. Then, use 2000 grit sandpaper dipped in water to sand the repaired area. The topcoat is now complete. Ensure the work area is well-ventilated. If the putty is applied too thickly, the interior will not dry. Therefore, control the coating thickness to within 1mm.
1
2
Share

Where is the OBD port on a Mercedes-Benz?

The OBD port on a Mercedes-Benz is located below the left side of the steering wheel. You can see it by opening the cover. The OBD port is a 16-pin female connector with a trapezoidal shape. Some models may have a protective cover over the OBD port. Common OBD port colors are black, white, or blue. Taking the Mercedes-Benz GLC 2021 260L 4MATIC Dynamic model as an example, its body dimensions are 4764mm in length, 1898mm in width, and 1642mm in height, with a wheelbase of 2973mm. The vehicle features multi-link independent suspension both front and rear, and is equipped with a 2.0T inline four-cylinder turbocharged engine, delivering a maximum power of 145kW and a maximum torque of 320Nm, paired with a 9-speed automatic transmission.
4
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.