What is the fuel consumption of the Volvo S60L?

1 Answers
DiJaxon
07/30/25 6:35am
Volvo S60L's fuel consumption is 8 to 9 liters. The following is information about the Volvo S60L: 1. Basic introduction: The Volvo S60L is a mid-size sedan produced by the factory located in Chengdu, Sichuan, China. The Volvo S60L is based on the prototype of the Volvo S60, with the only difference being that the S60L has an 80mm longer wheelbase compared to the S60. On November 24, 2017, Volvo officially announced the launch of the 2018 S60L Advance Edition. 2. Configuration: The 2018 S60L Advance Edition is equipped with a City Safety system and IAQS in-car air quality system, which can filter 95% of PM2.5 and automatically clean the in-car air before passengers enter the vehicle. In addition, the T5 and T6E models use a combination of cameras and radar for detection, capable of identifying vehicles, pedestrians, cyclists, and large animals.
Was this review help?
14
2
Share
More Forum Discussions

What is the difference between motorcycle license E and F?

Here are the differences between motorcycle license E and F: 1. Eligible vehicle types differ: License E allows driving two-wheeled motorcycles with an engine displacement exceeding 50ml or a maximum design speed exceeding 50km/h. License F permits driving lightweight motorcycles with an engine displacement below 50ml or a maximum design speed not exceeding 50km/h. 2. Driving scope varies: License E holders can operate regular two-wheeled motorcycles and lightweight motorcycles covered by License F, while License F only authorizes driving lightweight motorcycles without other eligible vehicle types. 3. License plate colors differ: License E plates are yellow, whereas License F plates are blue. 4. Examination requirements vary: The test vehicle for License E must be a regular two-wheeled motorcycle with at least four speed gears, while the test vehicle requirements for License F are determined by the provincial traffic management department of public security authorities.
16
1
Share

What is the function of a car's carbon canister solenoid valve?

The function of a car's carbon canister solenoid valve is to adsorb and filter gasoline vapors inside the fuel tank. It controls the entry of fuel vapors into the engine for combustion through the solenoid valve, thereby reducing fuel consumption and preventing excessive fuel tank pressure. A faulty carbon canister solenoid valve not only increases fuel consumption but also affects the normal operation of the car's engine. Methods to check the condition of the carbon canister solenoid valve: 1. If gas sprays out when opening the fuel tank cap, it indicates a damaged solenoid valve; 2. If gasoline vapors or dripping oil appear at the carbon canister's atmospheric vent, it indicates a damaged solenoid valve; 3. Symptoms like poor acceleration, jerking, unstable idle speed (fluctuating high and low), indicate a damaged solenoid valve; 4. If the engine fails to start after stalling or there are abnormal noises while driving, it indicates a damaged solenoid valve.
7
5
Share

What Does a Car Sleeper Look Like?

A sleeper is a berth that allows passengers to lie flat and sleep, essentially serving as a small bed installed within long-distance transportation vehicles. Here are some relevant details: 1. Longitudinal Arrangement: Sleeper berths in passenger vehicles should be arranged longitudinally (aligned with the direction of vehicle movement). The width of each berth should not be less than 450mm, the longitudinal spacing between berths should not be less than 1400mm, and the lateral spacing between adjacent berths should not be less than 350mm. For double-decker sleeper arrangements, the height of the upper berth should not be less than 780mm, and the clearance between berths should not be less than 750mm. 2. During Long-Distance Travel: Avoid carrying excessive cash on your person. It's advisable to bring a portable power bank to prevent being unable to charge your phone if it runs out of battery. During long-distance bus journeys, drink water in moderation.
8
0
Share

Why does the Maybach 62s require an A1 driver's license?

The Maybach 62s has a length of over 6 meters. According to relevant standards, vehicles with a length equal to or exceeding 6 meters, or with a seating capacity of 20 or more passengers, are classified as large buses or large sedans. Only drivers holding an A1 license are qualified to operate such vehicles, hence the Maybach 62s falls under the A1 license category. Additional Information: Maybach, with its noble lineage, has set new standards in the top-tier luxury sedan market. The new Maybach sedan embodies the concepts of technological leadership, elegance, aesthetics, and perfection. The perfect fusion of design, color, and materials results in the exquisite design of this top-class luxury sedan, further enhancing its grandeur and creating a distinctive style. The new Maybach sedan offers spacious interiors and elegant styling, showcasing a unique charm formed by the perfect harmony between classic and modern elements.
17
1
Share

How often should the spark plugs of the New Emgrand be replaced?

The spark plugs of the New Emgrand should be replaced every 20,000 kilometers. Spark plugs are a crucial component of gasoline engines, determining whether the engine can ignite properly. When the ignition coil, following the engine's firing order, delivers a pulsed voltage to the spark plug via the high-voltage wire, the spark plug uses this voltage to create an electric spark by ionizing the air between its two electrodes, thereby igniting the combustible air-fuel mixture in the engine cylinder. The New Emgrand is a compact model under Geely, with body dimensions of 4632mm in length, 1789mm in width, and 1470mm in height, and a wheelbase of 2650mm. In terms of power, the vehicle is equipped with a 1.5-liter inline 4-cylinder naturally aspirated engine, delivering a maximum power of 80KW and a maximum torque of 140NM, paired with either a 5-speed manual transmission or a CVT continuously variable transmission.
12
0
Share

What are the solutions to reduce noise in the Fit?

The solutions to reduce noise in the Fit are: 1. Install sound-absorbing foam material under the engine hood; 2. Apply sound-absorbing cotton material to the trunk, the bottom of the trunk, and the wheel arches on both sides of the trunk; 3. Install professional damping plates in areas prone to noise; 4. Install sealing strips inside the doors; 5. Replace the tires with quieter ones. Taking the 2020 Fit as an example, its body dimensions are 4096mm in length, 1695mm in width, and 1525mm in height, with a wheelbase of 2350mm and a fuel tank capacity of 40 liters. This model is equipped with a 1.5L naturally aspirated engine, delivering a maximum horsepower of 131 PS, a maximum power of 96 kW, and a maximum torque of 155 Nm, paired with a 5-speed manual transmission.
19
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.